diff options
Diffstat (limited to 'keyboards/massdrop/alt/config.h')
| -rw-r--r-- | keyboards/massdrop/alt/config.h | 30 |
1 files changed, 19 insertions, 11 deletions
diff --git a/keyboards/massdrop/alt/config.h b/keyboards/massdrop/alt/config.h index d28094c492..1a0a7c9768 100644 --- a/keyboards/massdrop/alt/config.h +++ b/keyboards/massdrop/alt/config.h @@ -43,6 +43,9 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* Temporary solution for matrix delay */ #define IGNORE_ATOMIC_BLOCK +/* Avoid out-of-bounds errors when SmartEEPROM is not enabled */ +#define EEPROM_SIZE 1024 + /* MCU Port name definitions */ #define PA 0 #define PB 1 @@ -50,22 +53,18 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* This Shift Register expands available hardware output lines to control additional peripherals */ /* It uses four lines from the MCU to provide 16 output lines */ /* Shift Register Clock configuration (MCU to ShiftRegister.RCLK) */ -#define SR_EXP_RCLK_PORT PB -#define SR_EXP_RCLK_PIN 14 +#define SR_EXP_RCLK_PIN B14 /* Shift Register Output Enable configuration (MCU to ShiftRegister.OE_N) */ -#define SR_EXP_OE_N_PORT PB -#define SR_EXP_OE_N_PIN 15 +#define SR_EXP_OE_PIN B15 /* SERCOM port to use for Shift Register SPI */ /* DATAOUT and SCLK must be configured to use hardware pins of this port */ -#define SR_EXP_SERCOM SERCOM2 +#define SPI_SERCOM SERCOM2 /* Shift Register SPI Data Out configuration (MCU.SERCOMx.PAD[0] to ShiftRegister.SER) */ -#define SR_EXP_DATAOUT_PORT PA -#define SR_EXP_DATAOUT_PIN 12 -#define SR_EXP_DATAOUT_MUX 2 +#define SPI_DATAOUT_PIN A12 +#define SPI_DATAOUT_MUX 2 /* Shift Register SPI Serial Clock configuration (MCU.SERCOMx.PAD[1] to ShiftRegister.SRCLK) */ -#define SR_EXP_SCLK_PORT PA -#define SR_EXP_SCLK_PIN 13 -#define SR_EXP_SCLK_MUX 2 +#define SPI_SCLK_PIN A13 +#define SPI_SCLK_MUX 2 /* Debug LED (Small LED Located near MCU) */ #define DEBUG_LED_ENABLE 1 @@ -94,6 +93,15 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define DEBUG_BOOT_TRACING_PORT PB #define DEBUG_BOOT_TRACING_PIN 23 +/* USB2422 config */ +#define USB2422_ADDRESS 0x58 +#define USB2422_VENDOR_ID 0x04D8 +#define USB2422_PRODUCT_ID 0xEEC5 +#define USB2422_DEVICE_VER 0x0101 +#define USB2422_MANUFACTURER "Massdrop Inc." +#define USB2422_PRODUCT "Massdrop Hub" +#define USB2422_ACTIVE_PIN A18 + /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ #define DEBOUNCE 5 |