diff options
Diffstat (limited to 'keyboards/kc60')
24 files changed, 879 insertions, 0 deletions
diff --git a/keyboards/kc60/Makefile b/keyboards/kc60/Makefile new file mode 100644 index 0000000000..9717b519c8 --- /dev/null +++ b/keyboards/kc60/Makefile @@ -0,0 +1,76 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/kc60/config.h b/keyboards/kc60/config.h new file mode 100644 index 0000000000..c4a9b9ff82 --- /dev/null +++ b/keyboards/kc60/config.h @@ -0,0 +1,164 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER You +#define PRODUCT kc60v2 +#define DESCRIPTION A custom keyboard + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 14 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ + +// Possible pins for columns include: F1 F0 E6 D7 D6 D4 C7 C6 B7 B5 B4 B3 B1 B0 +// Pins for rows include: D0 D1 F6 F7 D5 +// KC60 Version 2 +#define MATRIX_ROW_PINS { D0, D1, F6, F7, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B7, D4, B1, B0, B5, B4, D7, D6, B3 } +#define UNUSED_PINS + +#define BACKLIGHT_PIN B6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/kc60/kc60.c b/keyboards/kc60/kc60.c new file mode 100644 index 0000000000..746ac634a3 --- /dev/null +++ b/keyboards/kc60/kc60.c @@ -0,0 +1 @@ +#include "kc60.h" diff --git a/keyboards/kc60/kc60.h b/keyboards/kc60/kc60.h new file mode 100644 index 0000000000..34eab4b2a0 --- /dev/null +++ b/keyboards/kc60/kc60.h @@ -0,0 +1,23 @@ +#ifndef KC60_H +#define KC60_H + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguements +// The second converts the arguments into a multi-dimensional array +#define KEYMAP( \ + K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D, \ + K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D, \ + K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D, \ + K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D, \ + K40, K41, K42, K45, K4A, K4B, K4C, K4D \ + ) { \ + { K00, K01, K02, K03, K04, K05, K06, K07, K08, K09, K0A, K0B, K0C, K0D }, \ + { K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K1A, K1B, K1C, K1D }, \ + { K20, K21, K22, K23, K24, K25, K26, K27, K28, K29, K2A, K2B, K2C, K2D }, \ + { K30, K31, K32, K33, K34, K35, K36, K37, K38, K39, K3A, K3B, K3C, K3D }, \ + { K40, K41, K42, KC_NO, KC_NO, K45, KC_NO, KC_NO, KC_NO, KC_NO,K4A, K4B, K4C, K4D } \ +} + +#endif diff --git a/keyboards/kc60/keymaps/default/keymap.c b/keyboards/kc60/keymaps/default/keymap.c new file mode 100644 index 0000000000..6f8352c695 --- /dev/null +++ b/keyboards/kc60/keymaps/default/keymap.c @@ -0,0 +1,24 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "kc60.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [0] = KEYMAP( /* Basic QWERTY */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_RSFT, \ + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT, KC_RCTL, RESET \ + ), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + return MACRO_NONE; +}; diff --git a/keyboards/kc60/keymaps/sgoodwin/keymap.c b/keyboards/kc60/keymaps/sgoodwin/keymap.c new file mode 100644 index 0000000000..99e95c2326 --- /dev/null +++ b/keyboards/kc60/keymaps/sgoodwin/keymap.c @@ -0,0 +1,42 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "kc60.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* + * Toggles between colemak and qwerty by tapping the bottom right key. + * Holding capslock key gives a layer like the KBParadise v60. + */ + [0] = KEYMAP( /* Basic Colemak */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_F, KC_P, KC_G, KC_J, KC_L, KC_U, KC_Y, KC_SCLN, KC_LBRC, KC_RBRC, KC_BSLS, \ + MO(2), KC_A, KC_R, KC_S, KC_T, KC_D, KC_H, KC_N, KC_E, KC_I, KC_O, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_K, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_RSFT, \ + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT, KC_RCTL, DF(1) \ + ), + [1] = KEYMAP( /* Basic QWERTY */ + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + MO(2), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_RSFT, \ + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI, KC_RALT, KC_RCTL, DF(0) \ + ), + [2] = KEYMAP( /* KBP v60-like arrows, media keys, etc */ + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_UP, BL_INC, BL_DEC, BL_STEP, \ + KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_LEFT, KC_DOWN, KC_RIGHT, KC_NO, KC_TRNS, \ + KC_TRNS, KC_NO, KC_MPRV, KC_MPLY, KC_MNXT, KC_VOLD, KC_VOLU, KC_MUTE, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_NO, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_SPC, DEBUG, RESET, KC_TRNS, KC_NO \ + ), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + return MACRO_NONE; +}; diff --git a/keyboards/kc60/keymaps/stanleylai/Makefile b/keyboards/kc60/keymaps/stanleylai/Makefile new file mode 100644 index 0000000000..b8b2beda48 --- /dev/null +++ b/keyboards/kc60/keymaps/stanleylai/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +RGBLIGHT_ENABLE ?= yes # Enable WS2812 underglow RGB strip +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= yes # USB Nkey Rollover + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/kc60/keymaps/stanleylai/base_layer.png b/keyboards/kc60/keymaps/stanleylai/base_layer.png Binary files differnew file mode 100644 index 0000000000..97235c6af4 --- /dev/null +++ b/keyboards/kc60/keymaps/stanleylai/base_layer.png diff --git a/keyboards/kc60/keymaps/stanleylai/config.h b/keyboards/kc60/keymaps/stanleylai/config.h new file mode 100644 index 0000000000..b5024a6d02 --- /dev/null +++ b/keyboards/kc60/keymaps/stanleylai/config.h @@ -0,0 +1,3 @@ +// Use configs from WS2812 enabled Keymap + +#include "../ws2812/config.h" diff --git a/keyboards/kc60/keymaps/stanleylai/keymap.c b/keyboards/kc60/keymaps/stanleylai/keymap.c new file mode 100644 index 0000000000..a7ea6040d5 --- /dev/null +++ b/keyboards/kc60/keymaps/stanleylai/keymap.c @@ -0,0 +1,151 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "kc60.h" + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 +#define _RGBL 2 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + +// See base_layer.png and rgb_layer.png for layout reference + +// Base Default Layer +// Mac Modifier Layout. Use BootMagic to toggle GUI and ALT positions. +[_BL] = KEYMAP( + F(0), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + LT(_FL, KC_CAPS), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, MO(_FL), KC_UP, \ + KC_LCTL, KC_LALT, KC_LGUI, KC_SPC, KC_RGUI,KC_LEFT, KC_DOWN, KC_RGHT), + +// Function layer +[_FL] = KEYMAP( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + KC_NO, KC_MPRV,KC_UP, KC_MNXT,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_PSCR,KC_SLCK, KC_PAUS, KC_INS, \ + KC_TRNS,KC_LEFT,KC_DOWN,KC_RGHT,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_TRNS,KC_NO, KC_MUTE,KC_VOLD,KC_VOLU,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_TRNS, LT(_RGBL, KC_PGUP),\ + KC_TRNS,KC_TRNS,KC_TRNS, KC_MPLY, KC_TRNS,KC_HOME, KC_PGDN, KC_END), + +// RGB Layer +[_RGBL] = KEYMAP( + #ifdef RGBLIGHT_ENABLE + RESET, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_TRNS,KC_NO, F(1), F(2), F(3), F(4), F(5), F(6), F(7), F(8), BL_STEP,BL_TOGG, KC_TRNS, KC_TRNS,\ + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS), + #else + RESET, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, \ + KC_TRNS,KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, BL_STEP,BL_TOGG, KC_TRNS, KC_TRNS,\ + KC_TRNS,KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS,KC_TRNS, KC_TRNS, KC_TRNS), + #endif +}; + + +enum function_id { + SHIFT_ESC, + #ifdef RGBLIGHT_ENABLE + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL, + #endif +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_FUNCTION(SHIFT_ESC), + #ifdef RGBLIGHT_ENABLE + [1] = ACTION_FUNCTION(RGBLED_TOGGLE), + [2] = ACTION_FUNCTION(RGBLED_STEP_MODE), + [3] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [4] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [5] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [6] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [7] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [8] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + #endif +}; + +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + static uint8_t shift_esc_shift_mask; + switch (id) { + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + + #ifdef RGBLIGHT_ENABLE + + case RGBLED_TOGGLE: + //led operations + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + #endif + } +} diff --git a/keyboards/kc60/keymaps/stanleylai/readme.md b/keyboards/kc60/keymaps/stanleylai/readme.md new file mode 100644 index 0000000000..1db72610d4 --- /dev/null +++ b/keyboards/kc60/keymaps/stanleylai/readme.md @@ -0,0 +1,26 @@ +Stanley Lai's Split Right Shift with Dedicated Arrow Keys +====================== + + + +## Quantum MK Firmware +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Keymap Notes +- Keymap setup with split Right Shift in mind. +- Right-side modifiers are setup as dedicated arrow keys + +### Base Layer Reference +- Fn Layer indicated on keycap front legends. +- Tapping Caps Lock key toggles Caps. Holding it down momentarily switches us to the Fn Layer. +- Holding down "Fn" and "Page Down" momentarily switches us to the RGB Layer. Tapping "Page Down" behaves as expected. + + +### RGB Layer Reference + + +## WS2812 Support +By default, it is now setup for 16 LEDs on the PF5 breakout pin. See [included image](../ws2812/ws2812_wiring.jpg) for wiring reference. + +### Build +To build this keymap, simply run `make KEYMAP=stanleylai`. diff --git a/keyboards/kc60/keymaps/stanleylai/rgb_layer.png b/keyboards/kc60/keymaps/stanleylai/rgb_layer.png Binary files differnew file mode 100644 index 0000000000..2bba028bb3 --- /dev/null +++ b/keyboards/kc60/keymaps/stanleylai/rgb_layer.png diff --git a/keyboards/kc60/keymaps/wigguno/Makefile b/keyboards/kc60/keymaps/wigguno/Makefile new file mode 100644 index 0000000000..0d7d918d88 --- /dev/null +++ b/keyboards/kc60/keymaps/wigguno/Makefile @@ -0,0 +1,24 @@ + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= no # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= no # Console for debug(+400) +COMMAND_ENABLE ?= no # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= yes # USB Nkey Rollover +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/kc60/keymaps/wigguno/keymap.c b/keyboards/kc60/keymaps/wigguno/keymap.c new file mode 100644 index 0000000000..50b1d0f981 --- /dev/null +++ b/keyboards/kc60/keymaps/wigguno/keymap.c @@ -0,0 +1,62 @@ +// This keymap was designed to close to the default kc60 layout, with some useful changes, such as adding media keys. +// It also moves the reset key off the base layer, as in the default kc60 layout for this firmware. +// I have swapped FN and RGUI as my rainbow keyset has them in the opposite order. + +#include "kc60.h" + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + + /* Basic QWERTY + * ,-----------------------------------------------------------. + * |Esc | 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp | + * |-----------------------------------------------------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \ | + * |-----------------------------------------------------------| + * |CAPS | A| S| D| F| G| H| J| K| L| ;| '|Return | + * |-----------------------------------------------------------| + * |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift | + * |-----------------------------------------------------------| + * |Ctrl|Gui |Alt | Space |Alt |FN |Gui |Ctrl | + * `-----------------------------------------------------------' + */ + [0] = KEYMAP( + KC_ESC, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_NO, KC_RSFT, \ + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, MO(1), KC_RGUI, KC_RCTL \ + ), + + /* + * ,-----------------------------------------------------------. + * | ` |F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12| Del | + * |-----------------------------------------------------------| + * | | | Up| | | | | | | | PS| | | | + * |-----------------------------------------------------------| + * | |Lft|Dwn|Rgt| |BL-|BL+| | | | | | | + * |-----------------------------------------------------------| + * | |Prv| PP|Nxt| | | | |Hom|End| | | + * |-----------------------------------------------------------| + * | Rst| | | BL | | | | | + * `-----------------------------------------------------------' + * PS = Print Screen + * PP = Play/Pause + */ + [1] = KEYMAP( /* Function Layer */ + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DELETE, \ + KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_PSCR, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, BL_DEC, BL_INC, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_MPRV, KC_MPLY, KC_MNXT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_HOME, KC_END, KC_TRNS, KC_TRNS, KC_TRNS, \ + RESET, KC_TRNS, KC_TRNS, BL_TOGG, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS \ + ), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + return MACRO_NONE; +}; diff --git a/keyboards/kc60/keymaps/wigguno/readme.md b/keyboards/kc60/keymaps/wigguno/readme.md new file mode 100644 index 0000000000..55a9f60c7c --- /dev/null +++ b/keyboards/kc60/keymaps/wigguno/readme.md @@ -0,0 +1,14 @@ +Wigguno's KC60 Layout +====================== + +## Quantum MK Firmware +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Changes from default QMK layout +The default QMK layout for KC60 does not have a function layer. It also has the bootloader-mode reset key bound. This keymap fixes both of these by adding a sensible function layer (including moving the reset key onto it, far away from the FN key). + +### Changes from the default KC60 layout +The default KC60 layout is good, but it was missing media keys. I've added previous, play/pause and next. I've also removed some of the keys from the function layer I didn't use. + +### Build +To enable NKRO you must be in the keymaps/wigguno directory when running make. diff --git a/keyboards/kc60/keymaps/ws2812/Makefile b/keyboards/kc60/keymaps/ws2812/Makefile new file mode 100644 index 0000000000..891c444162 --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/Makefile @@ -0,0 +1,25 @@ + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +KEYBOARD_LOCK_ENABLE ?= yes # Allow locking of keyboard via magic key +BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality +RGBLIGHT_ENABLE ?= yes # Enable WS2812 underglow RGB strip +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover + +ifndef QUANTUM_DIR + include ../../../../Makefile +endif diff --git a/keyboards/kc60/keymaps/ws2812/config.h b/keyboards/kc60/keymaps/ws2812/config.h new file mode 100644 index 0000000000..933bb0d2d1 --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/config.h @@ -0,0 +1,10 @@ +#include "../../config.h" + +/* WS2812B RGB Underglow LED */ +#define ws2812_PORTREG PORTF +#define ws2812_DDRREG DDRF +#define ws2812_pin PF5 // Based on wiring depicted in ws2812_wiring.jpg +#define RGBLED_NUM 16 // Number of LEDs. Change this to match your use case. +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 diff --git a/keyboards/kc60/keymaps/ws2812/keymap.c b/keyboards/kc60/keymaps/ws2812/keymap.c new file mode 100644 index 0000000000..bd5bef787b --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/keymap.c @@ -0,0 +1,161 @@ +// This is the canonical layout file for the Quantum project. If you want to add another keyboard, +// this is the style you want to emulate. + +#include "kc60.h" + +// Used for SHIFT_ESC +#define MODS_CTRL_MASK (MOD_BIT(KC_LSHIFT)|MOD_BIT(KC_RSHIFT)) + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. +#define _BL 0 +#define _FL 1 + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + /* Keymap _BL: (Base Layer) Default Layer + * ,-----------------------------------------------------------. + * |Esc~| 1| 2| 3| 4| 5| 6| 7| 8| 9| 0| -| =|Backsp | + * |-----------------------------------------------------------| + * |Tab | Q| W| E| R| T| Y| U| I| O| P| [| ]| \ | + * |-----------------------------------------------------------| + * |CAPS | A| S| D| F| G| H| J| K| L| ;| '|Return | + * |-----------------------------------------------------------| + * |Shift | Z| X| C| V| B| N| M| ,| .| /|Shift | + * |-----------------------------------------------------------| + * |Ctrl|Gui |Alt | Space |Alt |Gui |FN |Ctrl | + * `-----------------------------------------------------------' + */ +[_BL] = KEYMAP( + F(0), KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN,KC_QUOT, KC_NO, KC_ENT, \ + KC_LSFT, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM,KC_DOT, KC_SLSH, KC_NO, KC_RSFT, \ + KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT,KC_RGUI, MO(_FL), KC_RCTL), + + /* Keymap _FL: Function Layer + * ,-----------------------------------------------------------. + * |~ |F1 |F2 |F3 |F4 |F5 |F6 |F7 |F8 |F9 |F10|F11|F12| DEL | + * |-----------------------------------------------------------| + * | | |UP | | | | | | | | |BL-|BL+|BL | + * |-----------------------------------------------------------| + * | |LFT|DWN|RGT| | | | | | | | | + * |-----------------------------------------------------------| + * | |FN1|FN2|FN3|FN4|FN5|FN6|FN7|FN8| | | | + * |-----------------------------------------------------------| + * | | | | | | | |RSET| + * `-----------------------------------------------------------' + */ +[_FL] = KEYMAP( + #ifdef RGBLIGHT_ENABLE + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC, BL_INC, BL_TOGG, \ + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, F(1), F(2), F(3), F(4), F(5), F(6), F(7), F(8), KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET), + #else + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_DEL, \ + KC_TRNS, KC_TRNS, KC_UP, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, BL_DEC, BL_INC, BL_TOGG, \ + KC_TRNS, KC_LEFT, KC_DOWN, KC_RGHT, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \ + KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, RESET), + #endif +}; + +enum function_id { + SHIFT_ESC, + #ifdef RGBLIGHT_ENABLE + RGBLED_TOGGLE, + RGBLED_STEP_MODE, + RGBLED_INCREASE_HUE, + RGBLED_DECREASE_HUE, + RGBLED_INCREASE_SAT, + RGBLED_DECREASE_SAT, + RGBLED_INCREASE_VAL, + RGBLED_DECREASE_VAL + #endif +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_FUNCTION(SHIFT_ESC), + #ifdef RGBLIGHT_ENABLE + [1] = ACTION_FUNCTION(RGBLED_TOGGLE), + [2] = ACTION_FUNCTION(RGBLED_STEP_MODE), + [3] = ACTION_FUNCTION(RGBLED_INCREASE_HUE), + [4] = ACTION_FUNCTION(RGBLED_DECREASE_HUE), + [5] = ACTION_FUNCTION(RGBLED_INCREASE_SAT), + [6] = ACTION_FUNCTION(RGBLED_DECREASE_SAT), + [7] = ACTION_FUNCTION(RGBLED_INCREASE_VAL), + [8] = ACTION_FUNCTION(RGBLED_DECREASE_VAL), + #endif +}; + +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + static uint8_t shift_esc_shift_mask; + switch (id) { + case SHIFT_ESC: + shift_esc_shift_mask = get_mods()&MODS_CTRL_MASK; + if (record->event.pressed) { + if (shift_esc_shift_mask) { + add_key(KC_GRV); + send_keyboard_report(); + } else { + add_key(KC_ESC); + send_keyboard_report(); + } + } else { + if (shift_esc_shift_mask) { + del_key(KC_GRV); + send_keyboard_report(); + } else { + del_key(KC_ESC); + send_keyboard_report(); + } + } + break; + //led operations + #ifdef RGBLIGHT_ENABLE + case RGBLED_TOGGLE: + if (record->event.pressed) { + rgblight_toggle(); + } + break; + case RGBLED_INCREASE_HUE: + if (record->event.pressed) { + rgblight_increase_hue(); + } + break; + case RGBLED_DECREASE_HUE: + if (record->event.pressed) { + rgblight_decrease_hue(); + } + break; + case RGBLED_INCREASE_SAT: + if (record->event.pressed) { + rgblight_increase_sat(); + } + break; + case RGBLED_DECREASE_SAT: + if (record->event.pressed) { + rgblight_decrease_sat(); + } + break; + case RGBLED_INCREASE_VAL: + if (record->event.pressed) { + rgblight_increase_val(); + } + break; + case RGBLED_DECREASE_VAL: + if (record->event.pressed) { + rgblight_decrease_val(); + } + break; + case RGBLED_STEP_MODE: + if (record->event.pressed) { + rgblight_step(); + } + break; + #endif + } +} diff --git a/keyboards/kc60/keymaps/ws2812/readme.md b/keyboards/kc60/keymaps/ws2812/readme.md new file mode 100644 index 0000000000..5588fd2d97 --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/readme.md @@ -0,0 +1,21 @@ +KC60 with WS2812 RGB Underglow +====================== + + + +## Quantum MK Firmware +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## WS2812 Support +By default, it is now setup for 16 LEDs on the PF5 breakout pin. See [included image](ws2812_wiring.jpg) for wiring reference. + +### Build +To build this keymap with WS2812 enabled, simply run `make KEYMAP=ws2812`. + +### Reference Images + + + + +### Additional Credits +Keymap based on work by [TerryMatthews](https://github.com/TerryMathews) for GH60 Satan. diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_example.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_example.jpg Binary files differnew file mode 100644 index 0000000000..5c62cfded3 --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/ws2812_example.jpg diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_underside-lit.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_underside-lit.jpg Binary files differnew file mode 100644 index 0000000000..2eab21433a --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/ws2812_underside-lit.jpg diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_underside.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_underside.jpg Binary files differnew file mode 100644 index 0000000000..159d63904f --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/ws2812_underside.jpg diff --git a/keyboards/kc60/keymaps/ws2812/ws2812_wiring.jpg b/keyboards/kc60/keymaps/ws2812/ws2812_wiring.jpg Binary files differnew file mode 100644 index 0000000000..61b749b667 --- /dev/null +++ b/keyboards/kc60/keymaps/ws2812/ws2812_wiring.jpg diff --git a/keyboards/kc60/readme.md b/keyboards/kc60/readme.md new file mode 100644 index 0000000000..acc0df68dc --- /dev/null +++ b/keyboards/kc60/readme.md @@ -0,0 +1,27 @@ +KC60 (version 2.0) keyboard firmware +====================== + +## Quantum MK Firmware +For the full Quantum feature list, see [the parent readme.md](/readme.md). + +## Building +Download or clone the whole firmware and navigate to the keyboards/kc60 folder. Once your dev env is setup, you'll be able to type `make` to generate your .hex - you can then use the Teensy Loader to program your .hex file. + +Depending on which keymap you would like to use, you will have to compile slightly differently. + +### Default +To build with the default keymap, simply run `make`. + +### Other Keymaps +Several version of keymap are available in advance but you are recommended to define your favorite layout yourself. To define your own keymap create file named `<name>.c` in the keymaps folder, and see keymap document (you can find in top readme.md) and existent keymap files. + +To build the firmware binary hex file with a keymap just do `make` with `KEYMAP` option like: +``` +$ make KEYMAP=[default|jack|<name>] +``` +Keymaps follow the format **__\<name\>.c__** and are stored in the `keymaps` folder. + +## WS2812 Support + + +Build with WS2812 Support by running `make KEYMAP=ws2812`. |
