summaryrefslogtreecommitdiff
path: root/keyboards/handwired/onekey/rules.mk
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/handwired/onekey/rules.mk')
-rw-r--r--keyboards/handwired/onekey/rules.mk79
1 files changed, 20 insertions, 59 deletions
diff --git a/keyboards/handwired/onekey/rules.mk b/keyboards/handwired/onekey/rules.mk
index cfa693a73b..245f9025d7 100644
--- a/keyboards/handwired/onekey/rules.mk
+++ b/keyboards/handwired/onekey/rules.mk
@@ -1,61 +1,22 @@
-
-
-# MCU name
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
# Build Options
-# comment out to disable the options.
+# change yes to no to disable
#
-BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-CONSOLE_ENABLE = yes # Console for debug(+400)
-COMMAND_ENABLE = yes # Commands for debug and configuration
-#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
-#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA \ No newline at end of file
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
+SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+NKRO_ENABLE = yes # USB Nkey Rollover
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
+RGBLIGHT_ENABLE = no # Enable keyboard RGB underglow
+MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+AUDIO_ENABLE = no # Audio output on port C6
+FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
+HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
+
+DEFAULT_FOLDER = handwired/onekey/promicro