summaryrefslogtreecommitdiff
path: root/keyboards/gh60/keymaps/robotmaxtron
diff options
context:
space:
mode:
Diffstat (limited to 'keyboards/gh60/keymaps/robotmaxtron')
-rw-r--r--keyboards/gh60/keymaps/robotmaxtron/Makefile112
1 files changed, 0 insertions, 112 deletions
diff --git a/keyboards/gh60/keymaps/robotmaxtron/Makefile b/keyboards/gh60/keymaps/robotmaxtron/Makefile
deleted file mode 100644
index 2b80ea00e3..0000000000
--- a/keyboards/gh60/keymaps/robotmaxtron/Makefile
+++ /dev/null
@@ -1,112 +0,0 @@
-#----------------------------------------------------------------------------
-# On command line:
-#
-# make all = Make software.
-#
-# make clean = Clean out built project files.
-#
-# make coff = Convert ELF to AVR COFF.
-#
-# make extcoff = Convert ELF to AVR Extended COFF.
-#
-# make program = Download the hex file to the device.
-# Please customize your programmer settings(PROGRAM_CMD)
-#
-# make teensy = Download the hex file to the device, using teensy_loader_cli.
-# (must have teensy_loader_cli installed).
-#
-# make dfu = Download the hex file to the device, using dfu-programmer (must
-# have dfu-programmer installed).
-#
-# make flip = Download the hex file to the device, using Atmel FLIP (must
-# have Atmel FLIP installed).
-#
-# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
-# (must have dfu-programmer installed).
-#
-# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
-# (must have Atmel FLIP installed).
-#
-# make debug = Start either simulavr or avarice as specified for debugging,
-# with avr-gdb or avr-insight as the front end for debugging.
-#
-# make filename.s = Just compile filename.c into the assembler code only.
-#
-# make filename.i = Create a preprocessed source file for use in submitting
-# bug reports to the GCC project.
-#
-# To rebuild project do "make clean" then "make all".
-#----------------------------------------------------------------------------
-
-# MCU name
-#MCU = at90usb1287
-MCU = atmega32u4
-
-# Processor frequency.
-# This will define a symbol, F_CPU, in all source code files equal to the
-# processor frequency in Hz. You can then use this symbol in your source code to
-# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
-# automatically to create a 32-bit value in your source code.
-#
-# This will be an integer division of F_USB below, as it is sourced by
-# F_USB after it has run through any CPU prescalers. Note that this value
-# does not *change* the processor frequency - it should merely be updated to
-# reflect the processor speed set externally so that the code can use accurate
-# software delays.
-F_CPU = 16000000
-
-
-#
-# LUFA specific
-#
-# Target architecture (see library "Board Types" documentation).
-ARCH = AVR8
-
-# Input clock frequency.
-# This will define a symbol, F_USB, in all source code files equal to the
-# input clock frequency (before any prescaling is performed) in Hz. This value may
-# differ from F_CPU if prescaling is used on the latter, and is required as the
-# raw input clock is fed directly to the PLL sections of the AVR for high speed
-# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
-# at the end, this will be done automatically to create a 32-bit value in your
-# source code.
-#
-# If no clock division is performed on the input clock inside the AVR (via the
-# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
-F_USB = $(F_CPU)
-
-# Interrupt driven control endpoint task(+60)
-OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
-
-
-# Boot Section Size in *bytes*
-# Teensy halfKay 512
-# Teensy++ halfKay 1024
-# Atmel DFU loader 4096
-# LUFA bootloader 4096
-# USBaspLoader 2048
-OPT_DEFS += -DBOOTLOADER_SIZE=4096
-
-
-# Build Options
-# comment out to disable the options.
-#
-BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
-MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
-EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
-# CONSOLE_ENABLE = yes # Console for debug(+400)
-# COMMAND_ENABLE = yes # Commands for debug and configuration
-KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key
-# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
-# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
-NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
-# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
-# MIDI_ENABLE = YES # MIDI controls
-# UNICODE_ENABLE = YES # Unicode
-# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID
-RGBLIGHT_ENABLE = yes # Enable RGB Underglow
-
-ifndef QUANTUM_DIR
- include ../../../../Makefile
-endif
-