diff options
Diffstat (limited to 'keyboards/custommk/bonsai_c4_template/config.h')
| -rw-r--r-- | keyboards/custommk/bonsai_c4_template/config.h | 79 |
1 files changed, 0 insertions, 79 deletions
diff --git a/keyboards/custommk/bonsai_c4_template/config.h b/keyboards/custommk/bonsai_c4_template/config.h deleted file mode 100644 index 192e9b0755..0000000000 --- a/keyboards/custommk/bonsai_c4_template/config.h +++ /dev/null @@ -1,79 +0,0 @@ -/* Copyright 2022 customMK - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see <http://www.gnu.org/licenses/>. - */ - -#pragma once - -#include "config_common.h" - -// This file includes example #defines to enable commonly-used functionality -// (SPI, PWM backlight, etc.) on specific pins. Capabilities you want to include -// should be added to the config.h for your keyboard. Not all capabilities are -// shown; for example: -// I2C is not shown because the QMK defaults are sufficient for SCL on B6 and SDA on B7 -// Serial communications (for split keyboards) is not shown because QMK defaults work -// for either pins A15 or B6 - -// If you need to change pins for PWM, SPI, I2C, or Serial communications, be aware that -// doing this may require changing the driver, channel, PAL (Pin ALternate function) mode, -// DMA stream, and/or DMA channel. - - -// Bonsai C4 wires up pin A9 for Vbus sensing pin by default. For spilt keyboards, this -// can be used to determine which half of the keyboard is plugged into USB. -// For boards using Bonsai C4 merely as a reference design, the VBUS sense pin A9 -// can be used for purposes other than Vbus sensing (e.g. the switch -// matrix). -// -// If A9 is needed for Vbus sensing, uncomment the line -// below. Most keyboards using Bonsai C4 can leave the line below -// commented out. -// -// #undef BOARD_OTG_NOVBUSSENS - -// FRAM configuration -#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A0 -#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR 8 // 96MHz / 8 = 12MHz; max supported by MB85R64 is 20MHz -#define EXTERNAL_EEPROM_PAGE_SIZE 64 // does not matter for FRAM, just sets the RAM buffer size in STM32F chip -#define DYNAMIC_KEYMAP_EEPROM_MAX_ADDR 8191 - -// External flash configuration -#define EXTERNAL_FLASH_SPI_SLAVE_SELECT_PIN B12 -#define EXTERNAL_FLASH_SPI_CLOCK_DIVISOR 1 // 96MHz; max supported by W25Q128JV is 133MHz -#define EXTERNAL_FLASH_BYTE_COUNT (16 * 1024 * 1024) //128Mbit or 16MByte -#define EXTERNAL_FLASH_PAGE_SIZE 256 -#define EXTERNAL_FLASH_SPI_TIMEOUT 200000 //datasheet max is 200 seconds for flash chip erase - -// SPI Configuration (needed for FRAM and FLASH) -#define SPI_DRIVER SPID1 -#define SPI_SCK_PIN B3 -#define SPI_MOSI_PIN B5 -#define SPI_MISO_PIN B4 - -// Example code to set up PWM backlight on pin A6 -// If a different pin is used, a different PWM driver/channel settings may be necessary -#define BACKLIGHT_PIN A6 -#define BACKLIGHT_PWM_DRIVER PWMD3 -#define BACKLIGHT_PWM_CHANNEL 1 - -// Example code for WS2812 underglow -// Only pin A10 is wired to send 5V signals to the WS2812 -// This also usually requires adding special wiring during board assembly -#define RGB_DI_PIN A10 -#define WS2812_PWM_DRIVER PWMD1 -#define WS2812_PWM_CHANNEL 3 -#define WS2812_PWM_PAL_MODE 1 -#define WS2812_DMA_STREAM STM32_DMA2_STREAM5 -#define WS2812_DMA_CHANNEL 6 |