1 files changed, 91 insertions, 0 deletions
diff --git a/keyboards/bastardkb/charybdis/4x6/keymaps/drashna/config.h b/keyboards/bastardkb/charybdis/4x6/keymaps/drashna/config.h
new file mode 100644
index 0000000000..f384318dc4
--- /dev/null
+++ b/keyboards/bastardkb/charybdis/4x6/keymaps/drashna/config.h
@@ -0,0 +1,91 @@
+/**
+ * Copyright 2021 Charly Delay <charly@codesink.dev> (@0xcharly)
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#undef MATRIX_COL_PINS
+#define MATRIX_COL_PINS \
+    { B0, B1, B10, B3, B4, B5 }
+#undef MATRIX_COL_PINS_RIGHT
+#define MATRIX_COL_PINS_RIGHT \
+    { B0, B1, B10, B3, B4, B5 }
+
+#undef MATRIX_ROW_PINS
+#define MATRIX_ROW_PINS \
+    { B15, A2, B8, A8, B9 }
+#undef MATRIX_ROW_PINS_RIGHT
+#define MATRIX_ROW_PINS_RIGHT \
+    { B15, A2, B8, A8, B9 }
+
+#define DIODE_DIRECTION ROW2COL
+#define SPLIT_HAND_PIN A3
+
+#undef RGB_DI_PIN
+#define RGB_DI_PIN A1
+#define WS2812_EXTERNAL_PULLUP
+#define WS2812_PWM_DRIVER PWMD2
+#define WS2812_PWM_CHANNEL 2
+#define WS2812_PWM_PAL_MODE 1
+#define WS2812_EXTERNAL_PULLUP
+#define WS2812_DMA_STREAM STM32_DMA1_STREAM1
+#define WS2812_DMA_CHANNEL 3
+#define WS2812_PWM_TARGET_PERIOD 800000
+
+#define DEBUG_LED_PIN     C13
+
+#undef SOFT_SERIAL_PIN
+// #define SERIAL_USART_FULL_DUPLEX  // Enable full duplex operation mode.
+#define SERIAL_USART_TX_PIN      A9
+// #define SERIAL_USART_RX_PIN      A3
+// #define SERIAL_USART_DRIVER      SD2
+// #define SERIAL_USART_TX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
+// #define SERIAL_USART_RX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
+// #define SERIAL_USART_TIMEOUT     100  // USART driver timeout. default 100
+// // #define SERIAL_USART_PIN_SWAP // swap RX and TX pins on master
+// // To use the highest possible baudrate (3.75Mbit/s) uncomment the following
+// // line, this can result in dropped communications so lower the speed if there
+// // are many timeouts.
+// // #define SERIAL_USART_SPEED (STM32_PCLK2 >> 4)
+
+#define CRC8_USE_TABLE
+#define CRC8_OPTIMIZE_SPEED
+
+/* spi config for eeprom and pmw3360 sensor */
+#define SPI_DRIVER                           SPID1
+#define SPI_SCK_PIN                          A5
+#define SPI_SCK_PAL_MODE                     5
+#define SPI_MOSI_PIN                         A7
+#define SPI_MOSI_PAL_MODE                    5
+#define SPI_MISO_PIN                         A6
+#define SPI_MISO_PAL_MODE                    5
+
+#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A4
+#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR    64
+
+#undef PMW3360_CS_PIN
+#define PMW3360_CS_PIN                       B14
+#define PMW3360_CS_MODE 3
+#define PMW3360_CS_DIVISOR 64
+
+#define CHARYBDIS_MINIMUM_DEFAULT_DPI     1200
+#define CHARYBDIS_DEFAULT_DPI_CONFIG_STEP 400
+#define CHARYBDIS_MINIMUM_SNIPING_DPI     200
+#define CHARYBDIS_SNIPING_DPI_CONFIG_STEP 100
+
+/* RGB Matrix. */
+
+#undef RGB_MATRIX_MAXIMUM_BRIGHTNESS
+#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 150