diff options
Diffstat (limited to 'keyboard/lufa/Makefile')
| -rw-r--r-- | keyboard/lufa/Makefile | 169 |
1 files changed, 0 insertions, 169 deletions
diff --git a/keyboard/lufa/Makefile b/keyboard/lufa/Makefile deleted file mode 100644 index 030f4061d2..0000000000 --- a/keyboard/lufa/Makefile +++ /dev/null @@ -1,169 +0,0 @@ -# Hey Emacs, this is a -*- makefile -*- -#---------------------------------------------------------------------------- -# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al. -# >> Modified for use with the LUFA project. << -# -# Released to the Public Domain -# -# Additional material for this makefile was written by: -# Peter Fleury -# Tim Henigan -# Colin O'Flynn -# Reiner Patommel -# Markus Pfaff -# Sander Pool -# Frederik Rouleau -# Carlos Lamas -# Dean Camera -# Opendous Inc. -# Denver Gingerich -# -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device, using avrdude. -# Please customize the avrdude settings below first! -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make doxygen = Generate DoxyGen documentation for the project (must have -# DoxyGen installed) -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# Directory common source filess exist -TOP_DIR = ../.. - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - - -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - - -# Target board (see library "Board Types" documentation, NONE for projects not requiring -# LUFA board drivers). If USER is selected, put custom board drivers in a directory called -# "Board" inside the application directory. -BOARD = USBKEY - - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - - -# Target file name (without extension). -TARGET = lufa - - -# Path to the LUFA library -LUFA_PATH = ../../protocol - -# Create the LUFA source path variables by including the LUFA root makefile -include $(LUFA_PATH)/LUFA/makefile - - - -# List C source files here. (C dependencies are automatically generated.) -LUFA_SRC = $(TARGET).c \ - descriptor.c \ - $(LUFA_SRC_USB) \ - $(LUFA_SRC_USBCLASS) - -SRC = $(subst $(LUFA_PATH)/LUFA/,,$(LUFA_SRC)) -SRC += keymap.c \ - matrix.c \ - led.c \ - pjrc/bootloader_teensy.c -CONFIG_H = config.h - - -# Build Options -# comment out to disable the options. -# -MOUSEKEY_ENABLE = yes # Mouse keys -#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support -EXTRAKEY_ENABLE = yes # Audio control and System control -#NKRO_ENABLE = yes # USB Nkey Rollover - - -# LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" - -OPT_DEFS = -DF_CPU=$(F_CPU)UL -OPT_DEFS += -DF_USB=$(F_USB)UL -OPT_DEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH) -OPT_DEFS += $(LUFA_OPTS) - - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(LUFA_PATH)/LUFA - - -include $(TOP_DIR)/protocol.mk -include $(TOP_DIR)/common.mk -include $(TOP_DIR)/rules.mk - -test: - echo $(SRC) |