diff options
Diffstat (limited to 'keyboard/jd45')
| -rw-r--r-- | keyboard/jd45/Makefile | 140 | ||||
| -rw-r--r-- | keyboard/jd45/backlight.c | 61 | ||||
| -rw-r--r-- | keyboard/jd45/config.h | 79 | ||||
| -rw-r--r-- | keyboard/jd45/jd45.c | 27 | ||||
| -rw-r--r-- | keyboard/jd45/jd45.h | 12 | ||||
| -rw-r--r-- | keyboard/jd45/keymaps/keymap_default.c | 31 | ||||
| -rw-r--r-- | keyboard/jd45/keymaps/keymap_justin.c | 101 |
7 files changed, 451 insertions, 0 deletions
diff --git a/keyboard/jd45/Makefile b/keyboard/jd45/Makefile new file mode 100644 index 0000000000..076dced829 --- /dev/null +++ b/keyboard/jd45/Makefile @@ -0,0 +1,140 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = jd45 + + +# Directory common source filess exist +TOP_DIR = ../.. +TMK_DIR = ../../tmk_core + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# # project specific files +SRC = jd45.c \ + backlight.c + +ifdef KEYMAP + SRC := keymaps/keymap_$(KEYMAP).c $(SRC) +else + SRC := keymaps/keymap_default.c $(SRC) +endif + +CONFIG_H = config.h + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +# NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +MIDI_ENABLE = YES # MIDI controls +# UNICODE_ENABLE = YES # Unicode +BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID + + +# Optimize size but this may cause error "relocation truncated to fit" +#EXTRALDFLAGS = -Wl,--relax + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) +VPATH += $(TMK_DIR) + +include $(TOP_DIR)/quantum/quantum.mk + diff --git a/keyboard/jd45/backlight.c b/keyboard/jd45/backlight.c new file mode 100644 index 0000000000..f69364b2af --- /dev/null +++ b/keyboard/jd45/backlight.c @@ -0,0 +1,61 @@ + +#include <avr/io.h> +#include "backlight.h" + +#define CHANNEL OCR1C + +void backlight_init_ports() +{ + + // Setup PB7 as output and output low. + DDRB |= (1<<7); + PORTB &= ~(1<<7); + + // Use full 16-bit resolution. + ICR1 = 0xFFFF; + + // I could write a wall of text here to explain... but TL;DW + // Go read the ATmega32u4 datasheet. + // And this: http://blog.saikoled.com/post/43165849837/secret-konami-cheat-code-to-high-resolution-pwm-on + + // Pin PB7 = OCR1C (Timer 1, Channel C) + // Compare Output Mode = Clear on compare match, Channel C = COM1C1=1 COM1C0=0 + // (i.e. start high, go low when counter matches.) + // WGM Mode 14 (Fast PWM) = WGM13=1 WGM12=1 WGM11=1 WGM10=0 + // Clock Select = clk/1 (no prescaling) = CS12=0 CS11=0 CS10=1 + + TCCR1A = _BV(COM1C1) | _BV(WGM11); // = 0b00001010; + TCCR1B = _BV(WGM13) | _BV(WGM12) | _BV(CS10); // = 0b00011001; + + backlight_init(); +} + +void backlight_set(uint8_t level) +{ + if ( level == 0 ) + { + // Turn off PWM control on PB7, revert to output low. + TCCR1A &= ~(_BV(COM1C1)); + CHANNEL = 0x0; + // Prevent backlight blink on lowest level + PORTB &= ~(_BV(PORTB7)); + } + else if ( level == BACKLIGHT_LEVELS ) + { + // Prevent backlight blink on lowest level + PORTB &= ~(_BV(PORTB7)); + // Turn on PWM control of PB7 + TCCR1A |= _BV(COM1C1); + // Set the brightness + CHANNEL = 0xFFFF; + } + else + { + // Prevent backlight blink on lowest level + PORTB &= ~(_BV(PORTB7)); + // Turn on PWM control of PB7 + TCCR1A |= _BV(COM1C1); + // Set the brightness + CHANNEL = 0xFFFF >> ((BACKLIGHT_LEVELS - level) * ((BACKLIGHT_LEVELS + 1) / 2)); + } +}
\ No newline at end of file diff --git a/keyboard/jd45/config.h b/keyboard/jd45/config.h new file mode 100644 index 0000000000..1b81fe32ed --- /dev/null +++ b/keyboard/jd45/config.h @@ -0,0 +1,79 @@ +/* +Copyright 2012 Jun Wako <wakojun@gmail.com> + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see <http://www.gnu.org/licenses/>. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0001 +#define MANUFACTURER geekhack +#define PRODUCT JD45 +#define DESCRIPTION q.m.k. keyboard firmware for JD45 + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 13 + +/* Planck PCB default pin-out */ +#define COLS (int []){F4, D7, B5, B6, C6, C7, D4, D6, D5, D0, D1, D2, B0} +#define ROWS (int []){F0, F1, F5, B4} + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ +#define BACKLIGHT_LEVELS 3 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCE 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +#define NO_DEBUG + +/* disable print */ +#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboard/jd45/jd45.c b/keyboard/jd45/jd45.c new file mode 100644 index 0000000000..d05714f07b --- /dev/null +++ b/keyboard/jd45/jd45.c @@ -0,0 +1,27 @@ +#include "jd45.h" + +__attribute__ ((weak)) +void * matrix_init_user(void) { + +}; + +__attribute__ ((weak)) +void * matrix_scan_user(void) { + +}; + +void * matrix_init_kb(void) { + #ifdef BACKLIGHT_ENABLE + backlight_init_ports(); + #endif + + if (matrix_init_user) { + (*matrix_init_user)(); + } +}; + +void * matrix_scan_kb(void) { + if (matrix_scan_user) { + (*matrix_scan_user)(); + } +}; diff --git a/keyboard/jd45/jd45.h b/keyboard/jd45/jd45.h new file mode 100644 index 0000000000..f07bd5e139 --- /dev/null +++ b/keyboard/jd45/jd45.h @@ -0,0 +1,12 @@ +#ifndef JD45_H +#define JD45_H + +#include "matrix.h" +#include "keymap_common.h" +#include "backlight.h" +#include <stddef.h> + +void * matrix_init_user(void); +void * matrix_scan_user(void); + +#endif diff --git a/keyboard/jd45/keymaps/keymap_default.c b/keyboard/jd45/keymaps/keymap_default.c new file mode 100644 index 0000000000..05dd46e792 --- /dev/null +++ b/keyboard/jd45/keymaps/keymap_default.c @@ -0,0 +1,31 @@ +#include "jd45.h" +#include "backlight.h" + +/* this keymap is to provide a basic keyboard layout for testing the matrix + * for more practical and complicated keymap refer to other keymaps in the same folder + */ +/* JD45 keymap definition macro + */ +#define KEYMAP( \ + K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, K13, \ + K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, K24, K25, \ + K26, K27, K28, K29, K30, K31, K32, K33, K34, K35, K36, K37, \ + K38, K39, K40, K41, K42, K43, K44, K45, K46, K47 \ +) { \ + { KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K10, KC_##K11, KC_##K12, KC_##K13 }, \ + { KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_NO }, \ + { KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_NO }, \ + { KC_##K38, KC_##K39, KC_##K40, KC_##K41, KC_##K42, KC_NO, KC_##K43, KC_NO, KC_##K44, KC_##K45, KC_##K46, KC_##K47, KC_NO } \ +} + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[0] = KEYMAP( + ESC, Q, W, E, R, T, Y, U, I, O, P, QUOT, BSPC, + TAB, A, S, D, F, G, H, J, K, L, SCLN, ENT, + LSFT, Z, X, C, V, B, N, M, COMM, DOT, SLSH, RSFT, + PAUSE, LCTL, LALT, DEL, SPC, DEL, LEFT, UP, DOWN, RIGHT ), +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; diff --git a/keyboard/jd45/keymaps/keymap_justin.c b/keyboard/jd45/keymaps/keymap_justin.c new file mode 100644 index 0000000000..f261b54633 --- /dev/null +++ b/keyboard/jd45/keymaps/keymap_justin.c @@ -0,0 +1,101 @@ +#include "jd45.h" +#include "backlight.h" + +/* JD45 keymap definition macro + */ +#define KEYMAP( \ + K01, K02, K03, K04, K05, K06, K07, K08, K09, K10, K11, K12, K13, \ + K14, K15, K16, K17, K18, K19, K20, K21, K22, K23, K24, K25, \ + K26, K27, K28, K29, K30, K31, K32, K33, K34, K35, K36, K37, \ + K38, K39, K40, K41, K42, K43, K44, K45, K46, K47 \ +) { \ + { KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07, KC_##K08, KC_##K09, KC_##K10, KC_##K11, KC_##K12, KC_##K13 }, \ + { KC_##K14, KC_##K15, KC_##K16, KC_##K17, KC_##K18, KC_##K19, KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_NO }, \ + { KC_##K26, KC_##K27, KC_##K28, KC_##K29, KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37, KC_NO }, \ + { KC_##K38, KC_##K39, KC_##K40, KC_##K41, KC_##K42, KC_NO, KC_##K43, KC_NO, KC_##K44, KC_##K45, KC_##K46, KC_##K47, KC_NO } \ +} + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[0] = KEYMAP( + ESC, Q, W, F, P, G, J, L, U, Y, SCLN, QUOT, BSPC, + FN8, A, R, S, T, D, H, N, E, I, O, ENT, + LSFT, Z, X, C, V, B, K, M, COMM, DOT, SLSH, FN6, + FN4, LGUI, FN7, FN2, FN1, SPC, FN5, RALT, FN3, FN0 ), +[1] = KEYMAP( + TRNS, FN10, FN11, FN12, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, UP, DEL, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, HOME, PGUP, LEFT, RGHT, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, END, PGDN, DOWN, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ), +[2] = KEYMAP( + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, 7, 8, 9, 0, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, LBRC, 4, 5, 6, DOT, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, RBRC, 1, 2, 3, BSLS, TRNS, + TRNS,FN29, TRNS, TRNS, TRNS, PAUSE, EQL, MINS, TRNS, TRNS ), +[3] = KEYMAP( + TRNS, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS ), +[4] = KEYMAP( + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, 7, 8, 9, 0, TRNS, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, LBRC, 4, 5, 6, DOT, TRNS, + TRNS, TRNS, TRNS, TRNS, TRNS, TRNS, RBRC, 1, 2, 3, BSLS, TRNS, + TRNS,FN29, TRNS, TRNS, TRNS, PAUSE, EQL, MINS, TRNS, TRNS ), +}; + +enum macro_id { + PSWD1, + PSWD2, + PSWD3, +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_MODS_TAP_KEY(MOD_LCTL, KC_MINS), + [1] = ACTION_LAYER_MOMENTARY(1), // FN1 + [2] = ACTION_LAYER_MOMENTARY(2), // FN2 + [3] = ACTION_LAYER_MOMENTARY(3), // FN3 + [4] = ACTION_MODS_TAP_KEY(MOD_LSFT, KC_GRV), + [5] = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_RGUI), + [6] = ACTION_MODS_TAP_KEY(MOD_RSFT, KC_CAPS), + [7] = ACTION_LAYER_MODS(4, MOD_LSFT), // FN4 + [8] = ACTION_MODS_TAP_KEY(MOD_LCTL, KC_TAB), + + [10] = ACTION_MACRO(PSWD1), + [11] = ACTION_MACRO(PSWD2), + [12] = ACTION_MACRO(PSWD3), + + [29] = ACTION_BACKLIGHT_TOGGLE(), + [30] = ACTION_BACKLIGHT_INCREASE(), + [31] = ACTION_BACKLIGHT_DECREASE() + +}; + +/* + * Macro definition + */ +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + switch (id) { + case PSWD1: + return (record->event.pressed ? + MACRO( I(0), T(1), T(2), T(3), T(4), T(5), T(6), T(7), T(8), T(ENT), END ) : + MACRO_NONE ); + case PSWD2: + return (record->event.pressed ? + MACRO( I(0), T(1), T(2), T(3), T(4), T(5), T(6), T(7), T(8), T(ENT), END ) : + MACRO_NONE ); + case PSWD3: + return (record->event.pressed ? + MACRO( I(0), T(1), T(2), T(3), T(4), T(5), T(6), T(7), T(8), T(ENT), END ) : + MACRO_NONE ); + //case VOLUP: + // return (record->event.pressed ? + // MACRO( D(VOLU), U(VOLU), END ) : + // MACRO_NONE ); + //case ALT_TAB: + // return (record->event.pressed ? + // MACRO( D(LALT), D(TAB), END ) : + // MACRO( U(TAB), END )); + } + return MACRO_NONE; +} |