diff options
Diffstat (limited to 'keyboard/hbkb')
| l---------[-rw-r--r--] | keyboard/hbkb/Makefile | 57 | ||||
| -rw-r--r-- | keyboard/hbkb/Makefile.lufa | 119 | ||||
| -rw-r--r-- | keyboard/hbkb/Makefile.pjrc | 56 | ||||
| -rw-r--r-- | keyboard/hbkb/config.h | 3 |
4 files changed, 179 insertions, 56 deletions
diff --git a/keyboard/hbkb/Makefile b/keyboard/hbkb/Makefile index 26be322e01..f00d036da3 100644..120000 --- a/keyboard/hbkb/Makefile +++ b/keyboard/hbkb/Makefile @@ -1,56 +1 @@ -# Target file name (without extension). -TARGET = hbk - -# Directory common source filess exist -TOP_DIR = ../.. - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = main.c \ - keymap.c \ - matrix.c \ - led.c - -CONFIG_H = config.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# Build Options -# comment out to disable the options. -# -MOUSEKEY_ENABLE = yes # Mouse keys -#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support -EXTRAKEY_ENABLE = yes # Audio control and System control -#NKRO_ENABLE = yes # USB Nkey Rollover - - - -#---------------- Programming Options -------------------------- -#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex -PROGRAM_CMD = /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) erase && \ - /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) flash $(TARGET).hex && \ - /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) start - - - -include $(TOP_DIR)/protocol/pjrc.mk -include $(TOP_DIR)/protocol.mk -include $(TOP_DIR)/common.mk -include $(TOP_DIR)/rules.mk +Makefile.lufa
\ No newline at end of file diff --git a/keyboard/hbkb/Makefile.lufa b/keyboard/hbkb/Makefile.lufa new file mode 100644 index 0000000000..c73a0ca7d1 --- /dev/null +++ b/keyboard/hbkb/Makefile.lufa @@ -0,0 +1,119 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = hbkb_lufa + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + + +# List C source files here. (C dependencies are automatically generated.) +SRC += keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support + + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOT_SIZE=4096 + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/lufa.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk diff --git a/keyboard/hbkb/Makefile.pjrc b/keyboard/hbkb/Makefile.pjrc new file mode 100644 index 0000000000..159f56b44b --- /dev/null +++ b/keyboard/hbkb/Makefile.pjrc @@ -0,0 +1,56 @@ +# Target file name (without extension). +TARGET = hbkb + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# keyboard dependent files +SRC = main.c \ + keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +#MCU = at90usb162 # Teensy 1.0 +MCU = atmega32u4 # Teensy 2.0 +#MCU = at90usb646 # Teensy++ 1.0 +#MCU = at90usb1286 # Teensy++ 2.0 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover + + + +#---------------- Programming Options -------------------------- +#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex +PROGRAM_CMD = /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) erase && \ + /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) flash $(TARGET).hex && \ + /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) start + + + +include $(TOP_DIR)/protocol/pjrc.mk +include $(TOP_DIR)/protocol.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk diff --git a/keyboard/hbkb/config.h b/keyboard/hbkb/config.h index 5262399dc3..deaabb2495 100644 --- a/keyboard/hbkb/config.h +++ b/keyboard/hbkb/config.h @@ -24,7 +24,10 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define VENDOR_ID 0xFEED #define PRODUCT_ID 0xBB00 #define MANUFACTURER t.m.k. +#define DEVICE_VER 0x0100 #define PRODUCT Happy Buckling Keyboard + + #define DESCRIPTION mod version of IBM Model M keyboard |