diff options
Diffstat (limited to 'keyboard/atomic/Makefile.pjrc')
| -rw-r--r-- | keyboard/atomic/Makefile.pjrc | 116 |
1 files changed, 0 insertions, 116 deletions
diff --git a/keyboard/atomic/Makefile.pjrc b/keyboard/atomic/Makefile.pjrc deleted file mode 100644 index be83ba18b1..0000000000 --- a/keyboard/atomic/Makefile.pjrc +++ /dev/null @@ -1,116 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# Target file name (without extension). -TARGET = gh60_pjrc - -# Directory common source filess exist -TOP_DIR = ../.. - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# project specific files -SRC = keymap_common.c \ - matrix.c \ - led.c - -ifdef KEYMAP - SRC := keymap_$(KEYMAP).c $(SRC) -else - SRC := keymap_jack.c $(SRC) -endif - -CONFIG_H = config.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -MCU = atmega32u4 -#MCU = at90usb1286 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+5000) -EXTRAKEY_ENABLE = yes # Audio control and System control(+600) -CONSOLE_ENABLE = yes # Console for debug -COMMAND_ENABLE = yes # Commands for debug and configuration -SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover(+500) -#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TOP_DIR) - -include $(TOP_DIR)/protocol/pjrc.mk -include $(TOP_DIR)/common.mk -include $(TOP_DIR)/rules.mk - -plain: OPT_DEFS += -DKEYMAP_PLAIN -plain: all - -poker: OPT_DEFS += -DKEYMAP_POKER -poker: all - -poker_set: OPT_DEFS += -DKEYMAP_POKER_SET -poker_set: all - -poker_bit: OPT_DEFS += -DKEYMAP_POKER_BIT -poker_bit: all |