summaryrefslogtreecommitdiff
path: root/drivers/sensors/pmw3360.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/sensors/pmw3360.c')
-rw-r--r--drivers/sensors/pmw3360.c279
1 files changed, 144 insertions, 135 deletions
diff --git a/drivers/sensors/pmw3360.c b/drivers/sensors/pmw3360.c
index 50d1c35801..0dac600cc2 100644
--- a/drivers/sensors/pmw3360.c
+++ b/drivers/sensors/pmw3360.c
@@ -16,67 +16,71 @@
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
+#include "spi_master.h"
#include "pmw3360.h"
#include "wait.h"
#include "debug.h"
#include "print.h"
-#include PMW3360_FIRMWARE_H
+#include "pmw3360_firmware.h"
// Registers
// clang-format off
-#define REG_Product_ID 0x00
-#define REG_Revision_ID 0x01
-#define REG_Motion 0x02
-#define REG_Delta_X_L 0x03
-#define REG_Delta_X_H 0x04
-#define REG_Delta_Y_L 0x05
-#define REG_Delta_Y_H 0x06
-#define REG_SQUAL 0x07
-#define REG_Raw_Data_Sum 0x08
-#define REG_Maximum_Raw_data 0x09
-#define REG_Minimum_Raw_data 0x0A
-#define REG_Shutter_Lower 0x0B
-#define REG_Shutter_Upper 0x0C
-#define REG_Control 0x0D
-#define REG_Config1 0x0F
-#define REG_Config2 0x10
-#define REG_Angle_Tune 0x11
-#define REG_Frame_Capture 0x12
-#define REG_SROM_Enable 0x13
-#define REG_Run_Downshift 0x14
-#define REG_Rest1_Rate_Lower 0x15
-#define REG_Rest1_Rate_Upper 0x16
-#define REG_Rest1_Downshift 0x17
-#define REG_Rest2_Rate_Lower 0x18
-#define REG_Rest2_Rate_Upper 0x19
-#define REG_Rest2_Downshift 0x1A
-#define REG_Rest3_Rate_Lower 0x1B
-#define REG_Rest3_Rate_Upper 0x1C
-#define REG_Observation 0x24
-#define REG_Data_Out_Lower 0x25
-#define REG_Data_Out_Upper 0x26
-#define REG_Raw_Data_Dump 0x29
-#define REG_SROM_ID 0x2A
-#define REG_Min_SQ_Run 0x2B
-#define REG_Raw_Data_Threshold 0x2C
-#define REG_Config5 0x2F
-#define REG_Power_Up_Reset 0x3A
-#define REG_Shutdown 0x3B
-#define REG_Inverse_Product_ID 0x3F
-#define REG_LiftCutoff_Tune3 0x41
-#define REG_Angle_Snap 0x42
-#define REG_LiftCutoff_Tune1 0x4A
-#define REG_Motion_Burst 0x50
-#define REG_LiftCutoff_Tune_Timeout 0x58
-#define REG_LiftCutoff_Tune_Min_Length 0x5A
-#define REG_SROM_Load_Burst 0x62
-#define REG_Lift_Config 0x63
-#define REG_Raw_Data_Burst 0x64
-#define REG_LiftCutoff_Tune2 0x65
+#define REG_Product_ID 0x00
+#define REG_Revision_ID 0x01
+#define REG_Motion 0x02
+#define REG_Delta_X_L 0x03
+#define REG_Delta_X_H 0x04
+#define REG_Delta_Y_L 0x05
+#define REG_Delta_Y_H 0x06
+#define REG_SQUAL 0x07
+#define REG_Raw_Data_Sum 0x08
+#define REG_Maximum_Raw_data 0x09
+#define REG_Minimum_Raw_data 0x0a
+#define REG_Shutter_Lower 0x0b
+#define REG_Shutter_Upper 0x0c
+#define REG_Control 0x0d
+#define REG_Config1 0x0f
+#define REG_Config2 0x10
+#define REG_Angle_Tune 0x11
+#define REG_Frame_Capture 0x12
+#define REG_SROM_Enable 0x13
+#define REG_Run_Downshift 0x14
+#define REG_Rest1_Rate_Lower 0x15
+#define REG_Rest1_Rate_Upper 0x16
+#define REG_Rest1_Downshift 0x17
+#define REG_Rest2_Rate_Lower 0x18
+#define REG_Rest2_Rate_Upper 0x19
+#define REG_Rest2_Downshift 0x1a
+#define REG_Rest3_Rate_Lower 0x1b
+#define REG_Rest3_Rate_Upper 0x1c
+#define REG_Observation 0x24
+#define REG_Data_Out_Lower 0x25
+#define REG_Data_Out_Upper 0x26
+#define REG_Raw_Data_Dump 0x29
+#define REG_SROM_ID 0x2a
+#define REG_Min_SQ_Run 0x2b
+#define REG_Raw_Data_Threshold 0x2c
+#define REG_Config5 0x2f
+#define REG_Power_Up_Reset 0x3a
+#define REG_Shutdown 0x3b
+#define REG_Inverse_Product_ID 0x3f
+#define REG_LiftCutoff_Tune3 0x41
+#define REG_Angle_Snap 0x42
+#define REG_LiftCutoff_Tune1 0x4a
+#define REG_Motion_Burst 0x50
+#define REG_LiftCutoff_Tune_Timeout 0x58
+#define REG_LiftCutoff_Tune_Min_Length 0x5a
+#define REG_SROM_Load_Burst 0x62
+#define REG_Lift_Config 0x63
+#define REG_Raw_Data_Burst 0x64
+#define REG_LiftCutoff_Tune2 0x65
+
+#define CPI_STEP 100
// clang-format on
+// limits to 0--119, resulting in a CPI range of 100 -- 12000 (as only steps of 100 are possible).
#ifndef MAX_CPI
-# define MAX_CPI 0x77 // limits to 0--119, should be max cpi/100
+# define MAX_CPI 0x77
#endif
bool _inBurst = false;
@@ -86,66 +90,50 @@ void print_byte(uint8_t byte) { dprintf("%c%c%c%c%c%c%c%c|", (byte & 0x80 ? '1'
#endif
#define constrain(amt, low, high) ((amt) < (low) ? (low) : ((amt) > (high) ? (high) : (amt)))
-bool spi_start_adv(void) {
+bool pmw3360_spi_start(void) {
bool status = spi_start(PMW3360_CS_PIN, PMW3360_SPI_LSBFIRST, PMW3360_SPI_MODE, PMW3360_SPI_DIVISOR);
+ // tNCS-SCLK, 120ns
wait_us(1);
return status;
}
-void spi_stop_adv(void) {
- wait_us(1);
- spi_stop();
-}
+spi_status_t pmw3360_write(uint8_t reg_addr, uint8_t data) {
+ pmw3360_spi_start();
-spi_status_t spi_write_adv(uint8_t reg_addr, uint8_t data) {
if (reg_addr != REG_Motion_Burst) {
_inBurst = false;
}
- spi_start_adv();
// send address of the register, with MSBit = 1 to indicate it's a write
spi_status_t status = spi_write(reg_addr | 0x80);
status = spi_write(data);
- // tSCLK-NCS for write operation
- wait_us(20);
-
- // tSWW/tSWR (=120us) minus tSCLK-NCS. Could be shortened, but is looks like a safe lower bound
- wait_us(100);
+ // tSCLK-NCS for write operation is 35us
+ wait_us(35);
spi_stop();
+
+ // tSWW/tSWR (=180us) minus tSCLK-NCS. Could be shortened, but is looks like a safe lower bound
+ wait_us(145);
return status;
}
-uint8_t spi_read_adv(uint8_t reg_addr) {
- spi_start_adv();
+uint8_t pmw3360_read(uint8_t reg_addr) {
+ pmw3360_spi_start();
// send adress of the register, with MSBit = 0 to indicate it's a read
spi_write(reg_addr & 0x7f);
-
+ // tSRAD (=160us)
+ wait_us(160);
uint8_t data = spi_read();
// tSCLK-NCS for read operation is 120ns
wait_us(1);
+ spi_stop();
// tSRW/tSRR (=20us) minus tSCLK-NCS
wait_us(19);
-
- spi_stop();
return data;
}
-void pmw3360_set_cpi(uint16_t cpi) {
- uint8_t cpival = constrain((cpi / 100) - 1, 0, MAX_CPI);
-
- spi_start_adv();
- spi_write_adv(REG_Config1, cpival);
- spi_stop();
-}
-
-uint16_t pmw3360_get_cpi(void) {
- uint8_t cpival = spi_read_adv(REG_Config1);
- return (uint16_t)((cpival + 1) & 0xFF) * 100;
-}
-
bool pmw3360_init(void) {
setPinOutput(PMW3360_CS_PIN);
@@ -153,42 +141,51 @@ bool pmw3360_init(void) {
_inBurst = false;
spi_stop();
- spi_start_adv();
+ pmw3360_spi_start();
spi_stop();
- spi_write_adv(REG_Shutdown, 0xb6); // Shutdown first
+ pmw3360_write(REG_Shutdown, 0xb6); // Shutdown first
wait_ms(300);
- spi_start_adv();
+ pmw3360_spi_start();
wait_us(40);
- spi_stop_adv();
+ spi_stop();
wait_us(40);
- spi_write_adv(REG_Power_Up_Reset, 0x5a);
+ // power up, need to first drive NCS high then low, see above.
+ pmw3360_write(REG_Power_Up_Reset, 0x5a);
wait_ms(50);
- spi_read_adv(REG_Motion);
- spi_read_adv(REG_Delta_X_L);
- spi_read_adv(REG_Delta_X_H);
- spi_read_adv(REG_Delta_Y_L);
- spi_read_adv(REG_Delta_Y_H);
+ // read registers and discard
+ pmw3360_read(REG_Motion);
+ pmw3360_read(REG_Delta_X_L);
+ pmw3360_read(REG_Delta_X_H);
+ pmw3360_read(REG_Delta_Y_L);
+ pmw3360_read(REG_Delta_Y_H);
pmw3360_upload_firmware();
- spi_stop_adv();
+ spi_stop();
wait_ms(10);
pmw3360_set_cpi(PMW3360_CPI);
wait_ms(1);
- spi_write_adv(REG_Config2, 0x00);
+ pmw3360_write(REG_Config2, 0x00);
- spi_write_adv(REG_Angle_Tune, constrain(ROTATIONAL_TRANSFORM_ANGLE, -30, 30));
+ pmw3360_write(REG_Angle_Tune, constrain(ROTATIONAL_TRANSFORM_ANGLE, -127, 127));
- spi_write_adv(REG_Lift_Config, PMW3360_LIFTOFF_DISTANCE);
+ pmw3360_write(REG_Lift_Config, PMW3360_LIFTOFF_DISTANCE);
bool init_success = pmw3360_check_signature();
+#ifdef CONSOLE_ENABLE
+ if (init_success) {
+ dprintf("pmw3360 signature verified");
+ } else {
+ dprintf("pmw3360 signature verification failed!");
+ }
+#endif
writePinLow(PMW3360_CS_PIN);
@@ -196,86 +193,98 @@ bool pmw3360_init(void) {
}
void pmw3360_upload_firmware(void) {
- spi_write_adv(REG_SROM_Enable, 0x1d);
+ // Datasheet claims we need to disable REST mode first, but during startup
+ // it's already disabled and we're not turning it on ...
+ // pmw3360_write(REG_Config2, 0x00); // disable REST mode
+ pmw3360_write(REG_SROM_Enable, 0x1d);
wait_ms(10);
- spi_write_adv(REG_SROM_Enable, 0x18);
+ pmw3360_write(REG_SROM_Enable, 0x18);
- spi_start_adv();
+ pmw3360_spi_start();
spi_write(REG_SROM_Load_Burst | 0x80);
wait_us(15);
+#ifdef PMW3360_LEGACY_FIRMWARE_UPLOAD
unsigned char c;
for (int i = 0; i < FIRMWARE_LENGTH; i++) {
c = (unsigned char)pgm_read_byte(firmware_data + i);
spi_write(c);
wait_us(15);
}
+#else
+ spi_transmit(firmware_data, sizeof(firmware_data));
+#endif
wait_us(200);
- spi_read_adv(REG_SROM_ID);
-
- spi_write_adv(REG_Config2, 0x00);
-
- spi_stop();
- wait_ms(10);
+ pmw3360_read(REG_SROM_ID);
+ pmw3360_write(REG_Config2, 0x00);
}
bool pmw3360_check_signature(void) {
- uint8_t pid = spi_read_adv(REG_Product_ID);
- uint8_t iv_pid = spi_read_adv(REG_Inverse_Product_ID);
- uint8_t SROM_ver = spi_read_adv(REG_SROM_ID);
+ uint8_t pid = pmw3360_read(REG_Product_ID);
+ uint8_t iv_pid = pmw3360_read(REG_Inverse_Product_ID);
+ uint8_t SROM_ver = pmw3360_read(REG_SROM_ID);
return (pid == firmware_signature[0] && iv_pid == firmware_signature[1] && SROM_ver == firmware_signature[2]); // signature for SROM 0x04
}
+uint16_t pmw3360_get_cpi(void) {
+ uint8_t cpival = pmw3360_read(REG_Config1);
+ return (uint16_t)((cpival + 1) & 0xFF) * CPI_STEP;
+}
+
+void pmw3360_set_cpi(uint16_t cpi) {
+ uint8_t cpival = constrain((cpi / CPI_STEP) - 1, 0, MAX_CPI);
+ pmw3360_write(REG_Config1, cpival);
+}
+
report_pmw3360_t pmw3360_read_burst(void) {
+ report_pmw3360_t report = {0};
+
if (!_inBurst) {
#ifdef CONSOLE_ENABLE
dprintf("burst on");
#endif
- spi_write_adv(REG_Motion_Burst, 0x00);
+ pmw3360_write(REG_Motion_Burst, 0x00);
_inBurst = true;
}
- spi_start_adv();
+ pmw3360_spi_start();
spi_write(REG_Motion_Burst);
- wait_us(35); // waits for tSRAD
+ wait_us(35); // waits for tSRAD_MOTBR
- report_pmw3360_t data = {0};
+ report.motion = spi_read();
+ spi_read(); // skip Observation
+ // delta registers
+ report.dx = spi_read();
+ report.mdx = spi_read();
+ report.dy = spi_read();
+ report.mdy = spi_read();
- data.motion = spi_read();
- spi_write(0x00); // skip Observation
- data.dx = spi_read();
- data.mdx = spi_read();
- data.dy = spi_read();
- data.mdy = spi_read();
+ if (report.motion & 0b111) { // panic recovery, sometimes burst mode works weird.
+ _inBurst = false;
+ }
spi_stop();
#ifdef CONSOLE_ENABLE
if (debug_mouse) {
- print_byte(data.motion);
- print_byte(data.dx);
- print_byte(data.mdx);
- print_byte(data.dy);
- print_byte(data.mdy);
+ print_byte(report.motion);
+ print_byte(report.dx);
+ print_byte(report.mdx);
+ print_byte(report.dy);
+ print_byte(report.mdy);
dprintf("\n");
}
#endif
- data.isMotion = (data.motion & 0x80) != 0;
- data.isOnSurface = (data.motion & 0x08) == 0;
- data.dx |= (data.mdx << 8);
- data.dx = data.dx * -1;
- data.dy |= (data.mdy << 8);
- data.dy = data.dy * -1;
-
- spi_stop();
+ report.isMotion = (report.motion & 0x80) != 0;
+ report.isOnSurface = (report.motion & 0x08) == 0;
+ report.dx |= (report.mdx << 8);
+ report.dx = report.dx * -1;
+ report.dy |= (report.mdy << 8);
+ report.dy = report.dy * -1;
- if (data.motion & 0b111) { // panic recovery, sometimes burst mode works weird.
- _inBurst = false;
- }
-
- return data;
+ return report;
}