summaryrefslogtreecommitdiff
path: root/converter/x68k_usb/Makefile
diff options
context:
space:
mode:
Diffstat (limited to 'converter/x68k_usb/Makefile')
-rw-r--r--converter/x68k_usb/Makefile101
1 files changed, 101 insertions, 0 deletions
diff --git a/converter/x68k_usb/Makefile b/converter/x68k_usb/Makefile
new file mode 100644
index 0000000000..a34e1c79ff
--- /dev/null
+++ b/converter/x68k_usb/Makefile
@@ -0,0 +1,101 @@
+#
+# Makefile for PJRC Teensy
+#
+
+
+# Target file name (without extension).
+TARGET = x68k_usb_pjrc
+
+# Directory common source filess exist
+TMK_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC = keymap.c \
+ matrix.c \
+ led.c \
+ protocol/serial_uart.c
+
+CONFIG_H = config_pjrc.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162 # Teensy 1.0
+MCU = atmega32u4 # Teensy 2.0
+#MCU = at90usb646 # Teensy++ 1.0
+#MCU = at90usb1286 # Teensy++ 2.0
+
+
+# Processor frequency.
+# Normally the first thing your program should do is set the clock prescaler,
+# so your program will run at the correct speed. You should also set this
+# variable to same clock speed. The _delay_ms() macro uses this, and many
+# examples use this variable to calculate timings. Do not add a "UL" here.
+F_CPU = 16000000
+
+
+# Boot Section Size in bytes
+# Teensy halfKay 512
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# *Comment out* to disable the options.
+#
+BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+
+
+
+#---------------- Programming Options --------------------------
+AVRDUDE = avrdude
+# Type: avrdude -c ? to get a full listing.
+AVRDUDE_PROGRAMMER = avr109
+AVRDUDE_PORT = /dev/ttyACM0
+AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
+#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
+
+# Uncomment the following if you want avrdude's erase cycle counter.
+# Note that this counter needs to be initialized first using -Yn,
+# see avrdude manual.
+#AVRDUDE_ERASE_COUNTER = -y
+
+# Uncomment the following if you do /not/ wish a verification to be
+# performed after programming the device.
+#AVRDUDE_NO_VERIFY = -V
+
+# Increase verbosity level. Please use this when submitting bug
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
+# to submit bug reports.
+#AVRDUDE_VERBOSE = -v -v
+
+AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
+#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
+AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
+AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+
+#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+
+include $(TMK_DIR)/protocol/pjrc.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk