summaryrefslogtreecommitdiff
path: root/converter/sun_usb/README
diff options
context:
space:
mode:
Diffstat (limited to 'converter/sun_usb/README')
-rw-r--r--converter/sun_usb/README178
1 files changed, 58 insertions, 120 deletions
diff --git a/converter/sun_usb/README b/converter/sun_usb/README
index 641f111303..7b4f95ca25 100644
--- a/converter/sun_usb/README
+++ b/converter/sun_usb/README
@@ -1,20 +1,15 @@
Sun to USB keyboard protocol converter
======================================
+Target MCU is ATMega32u4 but other USB capable AVR will also work.
+Supported keyboards: Sun Type 5 Keyboard, CTCSP SHORT TYPE KEYBOARD(CKUB)
+
+CTCSP SHORT TYPE KEYBOARD: http://imgur.com/a/QIv6p
-TODO
-----
-AVR UART engine expect positive logic while Sun keyboard signal is inverted serial.
-To use AVR UART engine you need inverter in front of RX and TX pin.
-Otherwise you can software serial routine to communicate the keyboard.
-Hardware
---------
-Target MCU is ATMega32u4 but other USB capable AVR will also work.
-You can use PJRC Teensy as dev board.
- http://www.pjrc.com/teensy/
Connector
+---------
8Pin mini DIN
___ ___
/ |_| \
@@ -24,118 +19,61 @@ Connector
\_____/
(receptacle)
-Wiring:
-Pin mini DIN Teensy
-----------------------------------
-1 GND GND
-2 GND GND
-3 5V
-4 RX/TX(Mouse)
-5 RX PD2
-6 TX PD3
-7 GND GND
-8 5V VCC
-
+ Wiring:
+ Pin mini DIN MCU
+ ----------------------------------
+ 1 GND GND
+ 2 GND GND
+ 3 5V
+ 4 RX/TX(Mouse)
+ 5 RX PD3
+ 6 TX PD2
+ 7 GND GND
+ 8 5V VCC
-Firmware
+Protocol
--------
-Build:
+Singnal: Asynchronous, Negative logic, 1200baud, No Flow control
+Frame format: 1-Start bit, 8-Data bits, No-Parity, 1-Stop bit
+
+ AVR USART engine expects positive logic while Sun keyboard signal is negative.
+ To use AVR UART engine you need exteral inverter in front of RX and TX pin.
+ Otherwise you can software serial routine to communicate the keyboard.
+
+This converter uses software method, you doesn't need any inverter part.
+
+
+Commands From System To Keyboard
+ 0x01 Reset
+ Keyboard responds with following byte sequence:
+ Success: 0xFF 0x04 0x7F
+ Fail: 0x7E 0x01 0x7F
+ 0x02 Bell On
+ 0x03 Bell Off
+ 0x0A Click On
+ 0x0B Click Off
+ 0x0E LED
+ followed by LED status byte:
+ bit: 3 2 1 0
+ LED: CapsLk ScrLk Compose NumLk
+ 0x0F Layout
+ Keyboard responds with 'Layout Response' 0xFE 0xXX
+
+Commands From Keyboard To System
+ 0x7F Idle
+ means no keys pressed.
+ 0xFE Layout Response
+ 0xFF Reset Response(followed by 0x04)
+
+Reference
+ http://kentie.net/article/sunkbd/page2.htm
+ http://kentie.net/article/sunkbd/KBD.pdf
+
+
+Build Firmware
+--------------
+Just use 'make'
$ cd sun_usb
$ make
-
-And load the binary to MCU with your favorite programmer.
-If you use Teensy you can load with PJRC Teensy Loader tool.
- http://www.pjrc.com/teensy/loader.html
-
-
-* * * * * * * * * * * * * * * * * *
-
-
-X68000 Keyboard Protocol
-========================
-http://kyoutan.jpn.org/uts/pc/pic/x68key/
-
-
-Connector
----------
-Mini DIN 7pin(female connector on computer side)
- 7 6 5
- o o o
- 4 o = o 3
- o o
- 2 1
-
- Mini-DIN
- -------------
- pin1 +5V
- pin2 MOUSE
- pin3 RXD
- pin4 TXD
- pin5 READY
- pin6 REMOTE
- pin7 GND
-
-
-Signaling
----------
-- TXD,RXD
- Asynchronous, 2400baud, 1-startbit(L), 8-databit, 1-stopbit(H)
-
-- READY
- ready/not ready(1/0)
-
-
-Data from keyboard
-------------------
-bit 7 make/break flag(0/1)
-bit 6-0 following scan code
-
-
-Data from computer
-------------------
-- LED contorol ON/OFF(0/1)
- bit 7 1(fixed)
- bit 6 全角
- bit 5 ひらがな
- bit 4 INS
- bit 3 CAPS
- bit 2 コード入力
- bit 1 ローマ字
- bit 0 かな
-
-- Repeat delay
- bit 7 0(fixed)
- bit 6 1(fixed)
- bit 5 1(fixed)
- bit 4 0(fixed)
- bit 3-0 delay
- REPEAT_DELAY = 200+delay*100 ms
- default: 500ms
-
-- Repeat time
- bit 7 0(fixed)
- bit 6 1(fixed)
- bit 5 1(fixed)
- bit 4 1(fixed)
- bit 3-0 time
- REPEAT_TIME = 30+time^2*5 ms
- default: 110ms
-
-
-Scan Codes
-----------
-,---. ,---. ,-------------------, ,-------------------. ,-----------. ,---------------.
-| 61| | 62| | 63| 64| 65| 66| 67| | 68| 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54|
-`---' `---' `-------------------' `-------------------' `-----------' `---------------'
-,-----------------------------------------------------------. ,-----------. ,---------------.
-| 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42|
-|-----------------------------------------------------------| |------------ |---------------|
-| 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46|
-|------------------------------------------------------. 1D | `---=====---' |---------------|
-| 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29| | ___| 3C|___ | 47| 48| 49| 4A|
-|-----------------------------------------------------------| | 3B|---| 3D| |-----------|---|
-| 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 34| 70 | `---| 3E|---' | 4B| 4C| 4D| |
-`-----------------------------------------------------------| .---=====---. |-----------| 4E|
- | 5F| 55 | 56 | 35 | 57 | 58 | 59 | 60| | 72 | 73 | | 4F| 50| 51| |
- `---------------------------------------------' `-----------' `---------------'
+Then, load the binary to MCU with your favorite programmer.