diff options
Diffstat (limited to 'converter/ps2_usb/Makefile.vusb')
| -rw-r--r-- | converter/ps2_usb/Makefile.vusb | 107 |
1 files changed, 107 insertions, 0 deletions
diff --git a/converter/ps2_usb/Makefile.vusb b/converter/ps2_usb/Makefile.vusb new file mode 100644 index 0000000000..facee69056 --- /dev/null +++ b/converter/ps2_usb/Makefile.vusb @@ -0,0 +1,107 @@ +# Target file name (without extension). +TARGET = ps2_usb_vusb + +# Directory common source filess exist +TMK_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# keyboard dependent files +SRC = keymap_common.c \ + matrix.c \ + led.c + +ifdef KEYMAP + SRC := keymap_$(KEYMAP).c $(SRC) +else + SRC := keymap_plain.c $(SRC) +endif + +# Use USART for PS/2. With V-USB INT and BUSYWAIT code is not useful. +SRC += protocol/ps2_usart.c +OPT_DEFS += -DPS2_USE_USART + +CONFIG_H = config.h + + +# V-USB debug level: To use ps2_usart.c level must be 0 +# ps2_usart.c requires USART to receive PS/2 signal. +OPT_DEFS += -DDEBUG_LEVEL=0 + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +#MCU = at90usb162 # Teensy 1.0 +#MCU = atmega32u4 # Teensy 2.0 +#MCU = at90usb646 # Teensy++ 1.0 +#MCU = at90usb1286 # Teensy++ 2.0 +MCU = atmega168 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 20000000 + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover +NO_UART = yes # UART is unavailable + + + +#---------------- Programming Options -------------------------- +AVRDUDE = avrdude +# Type: avrdude -c ? to get a full listing. +AVRDUDE_PROGRAMMER = usbasp +AVRDUDE_PORT = +AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex +#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep + +# Uncomment the following if you want avrdude's erase cycle counter. +# Note that this counter needs to be initialized first using -Yn, +# see avrdude manual. +#AVRDUDE_ERASE_COUNTER = -y + +# Uncomment the following if you do /not/ wish a verification to be +# performed after programming the device. +#AVRDUDE_NO_VERIFY = -V + +# Increase verbosity level. Please use this when submitting bug +# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> +# to submit bug reports. +#AVRDUDE_VERBOSE = -v -v + +#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) +AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) +AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) +AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) +AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) + +PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) + + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBasp 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=2048 + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TMK_DIR) + + +include $(TMK_DIR)/protocol.mk +include $(TMK_DIR)/common.mk +include $(TMK_DIR)/protocol/vusb.mk +include $(TMK_DIR)/rules.mk |