diff options
Diffstat (limited to 'converter/ps2_usb/Makefile.tmk_rev1')
| -rw-r--r-- | converter/ps2_usb/Makefile.tmk_rev1 | 98 |
1 files changed, 98 insertions, 0 deletions
diff --git a/converter/ps2_usb/Makefile.tmk_rev1 b/converter/ps2_usb/Makefile.tmk_rev1 new file mode 100644 index 0000000000..6aaef49969 --- /dev/null +++ b/converter/ps2_usb/Makefile.tmk_rev1 @@ -0,0 +1,98 @@ +# +# Makefile for TMK keyboard converter rev2 +# https://github.com/tmk/keyboard_converter#pcb-rev1 +# +# Target file name (without extension). +TARGET = ps2_usb_tmk_rev1 + +# Directory common source filess exist +TMK_DIR = ../../tmk_core + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# project specific files +SRC = keymap_common.c \ + matrix.c \ + led.c + +ifdef KEYMAP + SRC := keymap_$(KEYMAP).c $(SRC) +else + SRC := keymap_plain.c $(SRC) +endif + +CONFIG_H = config_tmk_rev1.h + + +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA + + +# PS/2 Options +# +PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened) +#PS2_USE_BUSYWAIT = yes # uses primitive reference code + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TMK_DIR) + +include $(TMK_DIR)/protocol.mk +include $(TMK_DIR)/protocol/lufa.mk +include $(TMK_DIR)/common.mk +include $(TMK_DIR)/rules.mk |