summaryrefslogtreecommitdiff
path: root/converter/m0110_usb/Makefile
diff options
context:
space:
mode:
Diffstat (limited to 'converter/m0110_usb/Makefile')
-rw-r--r--converter/m0110_usb/Makefile96
1 files changed, 96 insertions, 0 deletions
diff --git a/converter/m0110_usb/Makefile b/converter/m0110_usb/Makefile
new file mode 100644
index 0000000000..466285fe97
--- /dev/null
+++ b/converter/m0110_usb/Makefile
@@ -0,0 +1,96 @@
+# Target file name (without extension).
+TARGET = m0110_lufa
+
+# Directory common source filess exist
+TMK_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC = matrix.c \
+ led.c \
+ keymap_common.c \
+ m0110.c
+
+# To use own keymap file run make like: make keymap=hasu
+ifdef KEYMAP
+ SRC += keymap_$(KEYMAP).c
+else
+ SRC += keymap_default.c
+endif
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+MCU = atmega32u2 # TMK converter rev2
+#MCU = atmega32u4 # TMK converter rev1
+
+
+# Processor frequency.
+# Normally the first thing your program should do is set the clock prescaler,
+# so your program will run at the correct speed. You should also set this
+# variable to same clock speed. The _delay_ms() macro uses this, and many
+# examples use this variable to calculate timings. Do not add a "UL" here.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in bytes
+# Teensy halfKay 512
+# Atmel DFU loader 4096
+# LUFA bootloader 4096
+OPT_DEFS += -DBOOTLOADER_SIZE=4096
+
+
+# Build Options
+# *Comment out* to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = yes # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
+#KEYMAP_SECTION_ENABLE = yes # fixed address keymap for keymap editor
+
+
+
+#---------------- Programming Options --------------------------
+PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TMK_DIR)
+
+
+include $(TMK_DIR)/protocol/lufa.mk
+include $(TMK_DIR)/protocol.mk
+include $(TMK_DIR)/common.mk
+include $(TMK_DIR)/rules.mk