summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--converter/sun_usb/Makefile90
-rw-r--r--converter/sun_usb/README141
-rw-r--r--converter/sun_usb/config.h61
-rw-r--r--converter/sun_usb/keymap.c140
-rw-r--r--converter/sun_usb/led.c26
-rw-r--r--converter/sun_usb/matrix.c180
-rw-r--r--protocol/serial.c75
-rw-r--r--protocol/serial.h45
8 files changed, 758 insertions, 0 deletions
diff --git a/converter/sun_usb/Makefile b/converter/sun_usb/Makefile
new file mode 100644
index 0000000000..7c06f26ce8
--- /dev/null
+++ b/converter/sun_usb/Makefile
@@ -0,0 +1,90 @@
+#
+# Makefile for PJRC Teensy
+#
+
+
+# Target file name (without extension).
+TARGET = sun_usb
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC = keymap.c \
+ matrix.c \
+ led.c \
+ protocol/serial.c
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162 # Teensy 1.0
+MCU = atmega32u4 # Teensy 2.0
+#MCU = at90usb646 # Teensy++ 1.0
+#MCU = at90usb1286 # Teensy++ 2.0
+
+
+# Processor frequency.
+# Normally the first thing your program should do is set the clock prescaler,
+# so your program will run at the correct speed. You should also set this
+# variable to same clock speed. The _delay_ms() macro uses this, and many
+# examples use this variable to calculate timings. Do not add a "UL" here.
+F_CPU = 16000000
+
+
+# Build Options
+# *Comment out* to disable the options.
+#
+MOUSEKEY_ENABLE = yes # Mouse keys
+EXTRAKEY_ENABLE = yes # Audio control and System control
+NKRO_ENABLE = yes # USB Nkey Rollover
+
+
+
+#---------------- Programming Options --------------------------
+AVRDUDE = avrdude
+# Type: avrdude -c ? to get a full listing.
+AVRDUDE_PROGRAMMER = avr109
+AVRDUDE_PORT = /dev/ttyACM0
+AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
+#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
+
+# Uncomment the following if you want avrdude's erase cycle counter.
+# Note that this counter needs to be initialized first using -Yn,
+# see avrdude manual.
+#AVRDUDE_ERASE_COUNTER = -y
+
+# Uncomment the following if you do /not/ wish a verification to be
+# performed after programming the device.
+#AVRDUDE_NO_VERIFY = -V
+
+# Increase verbosity level. Please use this when submitting bug
+# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude>
+# to submit bug reports.
+#AVRDUDE_VERBOSE = -v -v
+
+AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
+#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER)
+AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
+AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
+AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
+
+#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
+#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+
+include $(TOP_DIR)/protocol/pjrc.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk
diff --git a/converter/sun_usb/README b/converter/sun_usb/README
new file mode 100644
index 0000000000..641f111303
--- /dev/null
+++ b/converter/sun_usb/README
@@ -0,0 +1,141 @@
+Sun to USB keyboard protocol converter
+======================================
+
+TODO
+----
+AVR UART engine expect positive logic while Sun keyboard signal is inverted serial.
+To use AVR UART engine you need inverter in front of RX and TX pin.
+Otherwise you can software serial routine to communicate the keyboard.
+
+
+Hardware
+--------
+Target MCU is ATMega32u4 but other USB capable AVR will also work.
+You can use PJRC Teensy as dev board.
+ http://www.pjrc.com/teensy/
+
+Connector
+ 8Pin mini DIN
+ ___ ___
+ / |_| \
+ / 8 7 6 \
+ | 5 4 3 |
+ \_ 2 1 _/
+ \_____/
+ (receptacle)
+
+Wiring:
+Pin mini DIN Teensy
+----------------------------------
+1 GND GND
+2 GND GND
+3 5V
+4 RX/TX(Mouse)
+5 RX PD2
+6 TX PD3
+7 GND GND
+8 5V VCC
+
+
+
+Firmware
+--------
+Build:
+ $ cd sun_usb
+ $ make
+
+And load the binary to MCU with your favorite programmer.
+If you use Teensy you can load with PJRC Teensy Loader tool.
+ http://www.pjrc.com/teensy/loader.html
+
+
+* * * * * * * * * * * * * * * * * *
+
+
+X68000 Keyboard Protocol
+========================
+http://kyoutan.jpn.org/uts/pc/pic/x68key/
+
+
+Connector
+---------
+Mini DIN 7pin(female connector on computer side)
+ 7 6 5
+ o o o
+ 4 o = o 3
+ o o
+ 2 1
+
+ Mini-DIN
+ -------------
+ pin1 +5V
+ pin2 MOUSE
+ pin3 RXD
+ pin4 TXD
+ pin5 READY
+ pin6 REMOTE
+ pin7 GND
+
+
+Signaling
+---------
+- TXD,RXD
+ Asynchronous, 2400baud, 1-startbit(L), 8-databit, 1-stopbit(H)
+
+- READY
+ ready/not ready(1/0)
+
+
+Data from keyboard
+------------------
+bit 7 make/break flag(0/1)
+bit 6-0 following scan code
+
+
+Data from computer
+------------------
+- LED contorol ON/OFF(0/1)
+ bit 7 1(fixed)
+ bit 6 全角
+ bit 5 ひらがな
+ bit 4 INS
+ bit 3 CAPS
+ bit 2 コード入力
+ bit 1 ローマ字
+ bit 0 かな
+
+- Repeat delay
+ bit 7 0(fixed)
+ bit 6 1(fixed)
+ bit 5 1(fixed)
+ bit 4 0(fixed)
+ bit 3-0 delay
+ REPEAT_DELAY = 200+delay*100 ms
+ default: 500ms
+
+- Repeat time
+ bit 7 0(fixed)
+ bit 6 1(fixed)
+ bit 5 1(fixed)
+ bit 4 1(fixed)
+ bit 3-0 time
+ REPEAT_TIME = 30+time^2*5 ms
+ default: 110ms
+
+
+Scan Codes
+----------
+,---. ,---. ,-------------------, ,-------------------. ,-----------. ,---------------.
+| 61| | 62| | 63| 64| 65| 66| 67| | 68| 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54|
+`---' `---' `-------------------' `-------------------' `-----------' `---------------'
+,-----------------------------------------------------------. ,-----------. ,---------------.
+| 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42|
+|-----------------------------------------------------------| |------------ |---------------|
+| 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46|
+|------------------------------------------------------. 1D | `---=====---' |---------------|
+| 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29| | ___| 3C|___ | 47| 48| 49| 4A|
+|-----------------------------------------------------------| | 3B|---| 3D| |-----------|---|
+| 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 34| 70 | `---| 3E|---' | 4B| 4C| 4D| |
+`-----------------------------------------------------------| .---=====---. |-----------| 4E|
+ | 5F| 55 | 56 | 35 | 57 | 58 | 59 | 60| | 72 | 73 | | 4F| 50| 51| |
+ `---------------------------------------------' `-----------' `---------------'
diff --git a/converter/sun_usb/config.h b/converter/sun_usb/config.h
new file mode 100644
index 0000000000..f5b0758ca4
--- /dev/null
+++ b/converter/sun_usb/config.h
@@ -0,0 +1,61 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#ifndef CONFIG_H
+#define CONFIG_H
+
+/* controller configuration */
+#include "controller_teensy.h"
+
+#define VENDOR_ID 0xFEED
+#define PRODUCT_ID 0x3333
+#define MANUFACTURER t.m.k.
+#define PRODUCT Sun keyboard converter
+#define DESCRIPTION converts Sun keyboard protocol into USB
+
+
+/* matrix size */
+#define MATRIX_ROWS 16
+#define MATRIX_COLS 8
+
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LALT) | MOD_BIT(KC_RALT)) || \
+ keyboard_report->mods == (MOD_BIT(KC_LCTRL) | MOD_BIT(KC_RSHIFT)) \
+)
+
+
+/* Serial(USART) configuration
+ * asynchronous, negative logic, 1200baud, no flow control
+ * 1-start bit, 8-data bit, non parity, 1-stop bit
+ */
+#ifdef __AVR_ATmega32U4__
+# define SERIAL_RX_VECT USART1_RX_vect
+# define SERIAL_RX_DATA UDR1
+# define SERIAL_RX_BAUD 1200
+# define SERIAL_RX_UBBR ((F_CPU/(16UL*SERIAL_RX_BAUD))-1)
+# define SERIAL_RX_INIT() do { \
+ UBRR1L = (uint8_t) SERIAL_RX_UBBR; \
+ UBRR1H = (uint8_t) (SERIAL_RX_UBBR>>8); \
+ UCSR1B |= (1<<RXCIE1) | (1<<RXEN1); \
+ } while(0)
+#else
+# error "Serial(USART) configuration is needed."
+#endif
+
+#endif
diff --git a/converter/sun_usb/keymap.c b/converter/sun_usb/keymap.c
new file mode 100644
index 0000000000..542b13c1bd
--- /dev/null
+++ b/converter/sun_usb/keymap.c
@@ -0,0 +1,140 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/pgmspace.h>
+#include "keycode.h"
+#include "util.h"
+#include "keymap.h"
+
+
+
+
+// Following macros help you to define a keymap with the form of actual keyboard layout.
+
+/* X68000 Keyboard Scan codes
+,-------. ,-------------------. ,---------------. ,---------------. ,-----------. ,---------------.
+| | | 61| | | | | | 63| 65| 66| 67| | 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54|
+`-------' `-------------------' `---------------' `---------------' `-----------' `---------------'
+,-------. ,-----------------------------------------------------------. ,-----------. ,---------------.
+| | | | 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42|
+|-------| |-----------------------------------------------------------| |------------ |---------------|
+| | | | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46|
+|-------| |-----------------------------------------------------------| `-----------' |-----------| |
+| | | | 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29 | | 47| 48| 49| 4A|
+|-------| |-----------------------------------------------------------| ,---. |-----------|---|
+| | | | 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 70 | | 3E| | 4B| 4C| 4D| |
+|-------| |-----------------------------------------------------------| .-----------. |-----------| 4E|
+| | | | | | | 35 | | | | | | |73 | | 4F| 50| 51| |
+`-------' `-----------------------------------------------------------' `-----------' `---------------'
+*/
+#define KEYMAP( \
+ K61,K62, K63,K64,K65,K66,K67, K68,K69,K6A,K6B,K6C, K5A,K5B,K5C, K5D,K52,K53,K54, \
+ K01,K02,K03,K04,K05,K06,K07,K08,K09,K0A,K0B,K0C,K0D,K0E,K0F, K36,K5E,K37, K3F,K40,K41,K42, \
+ K10,K11,K12,K13,K14,K15,K16,K17,K18,K19,K1A,K1B,K1C, K1D, K38,K39,K3A, K43,K44,K45,K46, \
+ K71,K1E,K1F,K20,K21,K22,K23,K24,K25,K26,K27,K28,K29, K3C, K47,K48,K49,K4A, \
+ K70,K2A,K2B,K2C,K2D,K2E,K2F,K30,K31,K32,K33,K34, K3B,K3E,K3D, K4B,K4C,K4D,K4E, \
+ K5F,K55,K56, K35, K57,K58,K59,K60, K72, K73, K4F,K50,K51 \
+) { \
+ { KC_NO, KC_##K01, KC_##K02, KC_##K03, KC_##K04, KC_##K05, KC_##K06, KC_##K07 }, \
+ { KC_##K08, KC_##K09, KC_##K0A, KC_##K0B, KC_##K0C, KC_##K0D, KC_##K0E, KC_##K0F }, \
+ { KC_##K10, KC_##K11, KC_##K12, KC_##K13, KC_##K14, KC_##K15, KC_##K16, KC_##K17 }, \
+ { KC_##K18, KC_##K19, KC_##K1A, KC_##K1B, KC_##K1C, KC_##K1D, KC_##K1E, KC_##K1F }, \
+ { KC_##K20, KC_##K21, KC_##K22, KC_##K23, KC_##K24, KC_##K25, KC_##K26, KC_##K27 }, \
+ { KC_##K28, KC_##K29, KC_##K2A, KC_##K2B, KC_##K2C, KC_##K2D, KC_##K2E, KC_##K2F }, \
+ { KC_##K30, KC_##K31, KC_##K32, KC_##K33, KC_##K34, KC_##K35, KC_##K36, KC_##K37 }, \
+ { KC_##K38, KC_##K39, KC_##K3A, KC_##K3B, KC_##K3C, KC_##K3D, KC_##K3E, KC_##K3F }, \
+ { KC_##K40, KC_##K41, KC_##K42, KC_##K43, KC_##K44, KC_##K45, KC_##K46, KC_##K47 }, \
+ { KC_##K48, KC_##K49, KC_##K4A, KC_##K4B, KC_##K4C, KC_##K4D, KC_##K4E, KC_##K4F }, \
+ { KC_##K50, KC_##K51, KC_##K52, KC_##K53, KC_##K54, KC_##K55, KC_##K56, KC_##K57 }, \
+ { KC_##K58, KC_##K59, KC_##K5A, KC_##K5B, KC_##K5C, KC_##K5D, KC_##K5E, KC_##K5F }, \
+ { KC_##K60, KC_##K61, KC_##K62, KC_##K63, KC_##K64, KC_##K65, KC_##K66, KC_##K67 }, \
+ { KC_##K68, KC_##K69, KC_##K6A, KC_##K6B, KC_##K6C, KC_NO, KC_NO, KC_NO }, \
+ { KC_##K70, KC_##K71, KC_##K72, KC_##K73, KC_NO, KC_NO, KC_NO, KC_NO, }, \
+ { KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO } \
+}
+
+
+// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed.
+static const uint8_t PROGMEM fn_layer[] = {
+ 0, // Fn0
+ 0, // Fn1
+ 0, // Fn2
+ 0, // Fn3
+ 0, // Fn4
+ 0, // Fn5
+ 0, // Fn6
+ 0 // Fn7
+};
+
+// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer.
+// See layer.c for details.
+static const uint8_t PROGMEM fn_keycode[] = {
+ KC_NO, // Fn0
+ KC_NO, // Fn1
+ KC_NO, // Fn2
+ KC_NO, // Fn3
+ KC_NO, // Fn4
+ KC_NO, // Fn5
+ KC_NO, // Fn6
+ KC_NO // Fn7
+};
+
+
+static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+/* X68000 Keyboard Scan codes
+ ,---. ,---. ,-------------------, ,-------------------. ,-----------. ,---------------.
+ | 61| | 62| | 63| 64| 65| 66| 67| | 68| 69| 6A| 6B| 6C| | 5A| 5B| 5C| | 5D| 52| 53| 54|
+ `---' `---' `-------------------' `-------------------' `-----------' `---------------'
+ ,-----------------------------------------------------------. ,-----------. ,---------------.
+ | 01| 02| 03| 04| 05| 06| 07| 08| 09| 0A| 0B| 0C| 0D| 0E| 0F| | 36| 5E| 37| | 3F| 40| 41| 42|
+ |-----------------------------------------------------------| |------------ |---------------|
+ | 10 | 11| 12| 13| 14| 15| 16| 17| 18| 19| 1A| 1B| 1C| | | 38| 39| 3A| | 43| 44| 45| 46|
+ |------------------------------------------------------. 1D | `---=====---' |---------------|
+ | 71 | 1E| 1F| 20| 21| 2l| 23| 24| 25| 26| 27| 28| 29| | ___| 3C|___ | 47| 48| 49| 4A|
+ |-----------------------------------------------------------| | 3B|---| 3D| |-----------|---|
+ | 70 | 2A| 2B| 2C| 2D| 2E| 2F| 30| 31| 32| 33| 34| 70 | `---| 3E|---' | 4B| 4C| 4D| |
+ `-----------------------------------------------------------| .---=====---. |-----------| 4E|
+ | 5F| 55 | 56 | 35 | 57 | 58 | 59 | 60| | 72 | 73 | | 4F| 50| 51| |
+ `---------------------------------------------' `-----------' `---------------'
+*/
+ KEYMAP(
+ NO, NO, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, PSCR,SLCK,PAUS, CAPS,NO, NO, NO,
+ ESC, 1, 2, 3, 4, 5, 6, 7, 8, 9, 0, MINS,EQL, BSLS,BSPC, INS, HOME,PGUP, NLCK,PSLS,PAST,PMNS,
+ TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC, ENT, DEL, END, PGDN, P7, P8, P9, PPLS,
+ LCTL,A, S, D, F, G, H, J, K, L, SCLN,QUOT,ENT, UP, P4, P5, P6, PEQL,
+ LSFT,Z, X, C, V, B, N, M, COMM,DOT, SLSH,GRV, LEFT,DOWN,RGHT, P1, P2, P3, PENT,
+ LGUI,LALT,NO, SPC, RALT,RGUI,RCTL,APP, NO, NO, P0, PCMM,PDOT
+ ),
+};
+
+
+uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col)
+{
+ return pgm_read_byte(&keymaps[(layer)][(row)][(col)]);
+}
+
+uint8_t keymap_fn_layer(uint8_t fn_bits)
+{
+ return pgm_read_byte(&fn_layer[biton(fn_bits)]);
+}
+
+uint8_t keymap_fn_keycode(uint8_t fn_bits)
+{
+ return pgm_read_byte(&fn_keycode[(biton(fn_bits))]);
+}
diff --git a/converter/sun_usb/led.c b/converter/sun_usb/led.c
new file mode 100644
index 0000000000..68ccc63527
--- /dev/null
+++ b/converter/sun_usb/led.c
@@ -0,0 +1,26 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include "stdint.h"
+#include "serial.h"
+#include "led.h"
+
+
+void led_set(uint8_t usb_led)
+{
+ // not supported now
+}
diff --git a/converter/sun_usb/matrix.c b/converter/sun_usb/matrix.c
new file mode 100644
index 0000000000..c1e98257d9
--- /dev/null
+++ b/converter/sun_usb/matrix.c
@@ -0,0 +1,180 @@
+/*
+Copyright 2012 Jun Wako <wakojun@gmail.com>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http://www.gnu.org/licenses/>.
+*/
+
+#include <stdint.h>
+#include <stdbool.h>
+#include <avr/io.h>
+#include <util/delay.h>
+#include "print.h"
+#include "util.h"
+#include "serial.h"
+#include "matrix.h"
+#include "debug.h"
+
+
+/*
+ * Matrix Array usage:
+ *
+ * ROW: 16(4bits)
+ * COL: 8(3bits)
+ *
+ * 8bit wide
+ * +---------+
+ * 0|00 ... 07|
+ * 1|08 ... 0F|
+ * :| ... |
+ * :| ... |
+ * E|70 ... 77|
+ * F|78 ... 7F|
+ * +---------+
+ *
+ * Command From System To Keyboard
+ * 0x01 Reset
+ * 0x02 Bell On
+ * 0x03 Bell Off
+ * 0x0A Click On
+ * 0x0B Click Off
+ * 0x0E LED
+ * 0x0F Layout
+ *
+ * Command From Keyboard To System
+ * 0x7F Idle
+ * 0xFE Layout Response
+ * 0xFF Reset Response(followed by 0x04)
+ *
+ * bit: 3 2 1 0
+ * LED: CapsLk ScrLk Compose NumLk
+ *
+ * Connector
+ * 8Pin mini DIN
+ * 8 7 6
+ * 5 4 3
+ * 2 1
+ * receptacle
+ *
+ * 1: GND
+ * 2: GND
+ * 3: 5V
+ * 4: RX/TX(Mouse)
+ * 5: RX
+ * 6: TX
+ * 7: GND
+ * 8: 5V
+ */
+static uint8_t matrix[MATRIX_ROWS];
+#define ROW(code) ((code>>3)&0xF)
+#define COL(code) (code&0x07)
+
+static bool is_modified = false;
+
+
+inline
+uint8_t matrix_rows(void)
+{
+ return MATRIX_ROWS;
+}
+
+inline
+uint8_t matrix_cols(void)
+{
+ return MATRIX_COLS;
+}
+
+void matrix_init(void)
+{
+ print_enable = true;
+ debug_enable = true;
+
+ serial_init();
+
+ // initialize matrix state: all keys off
+ for (uint8_t i=0; i < MATRIX_ROWS; i++) matrix[i] = 0x00;
+
+ return;
+}
+
+uint8_t matrix_scan(void)
+{
+ is_modified = false;
+
+ uint8_t code;
+ code = serial_recv();
+ if (code == 0) {
+ return 0;
+ }
+
+ phex(code); print("(");
+ code = ~code;
+ phex(code); print(")");
+return 0;
+ if (code&0x80) {
+ // break code
+ if (matrix_is_on(ROW(code), COL(code))) {
+ matrix[ROW(code)] &= ~(1<<COL(code));
+ is_modified = true;
+ }
+ } else {
+ // make code
+ if (!matrix_is_on(ROW(code), COL(code))) {
+ matrix[ROW(code)] |= (1<<COL(code));
+ is_modified = true;
+ }
+ }
+ return code;
+}
+
+bool matrix_is_modified(void)
+{
+ return is_modified;
+}
+
+inline
+bool matrix_has_ghost(void)
+{
+ return false;
+}
+
+inline
+bool matrix_is_on(uint8_t row, uint8_t col)
+{
+ return (matrix[row] & (1<<col));
+}
+
+inline
+uint8_t matrix_get_row(uint8_t row)
+{
+ return matrix[row];
+}
+
+void matrix_print(void)
+{
+ print("\nr/c 01234567\n");
+ for (uint8_t row = 0; row < matrix_rows(); row++) {
+ phex(row); print(": ");
+ pbin_reverse(matrix_get_row(row));
+ print("\n");
+ }
+}
+
+uint8_t matrix_key_count(void)
+{
+ uint8_t count = 0;
+ for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
+ count += bitpop(matrix[i]);
+ }
+ return count;
+}
diff --git a/protocol/serial.c b/protocol/serial.c
new file mode 100644
index 0000000000..b5c2ae3172
--- /dev/null
+++ b/protocol/serial.c
@@ -0,0 +1,75 @@
+/*
+Copyright 2012 Jun WAKO <wakojun@gmail.com>
+
+This software is licensed with a Modified BSD License.
+All of this is supposed to be Free Software, Open Source, DFSG-free,
+GPL-compatible, and OK to use in both free and proprietary applications.
+Additions and corrections to this file are welcome.
+
+
+Redistribution and use in source and binary forms, with or without
+modification, are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+* Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+* Neither the name of the copyright holders nor the names of
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGE.
+*/
+
+#include <stdbool.h>
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include "serial.h"
+
+
+void serial_init(void)
+{
+ SERIAL_RX_INIT();
+}
+
+// RX ring buffer
+#define RBUF_SIZE 8
+static uint8_t rbuf[RBUF_SIZE];
+static uint8_t rbuf_head = 0;
+static uint8_t rbuf_tail = 0;
+
+uint8_t serial_recv(void)
+{
+ uint8_t data = 0;
+ if (rbuf_head == rbuf_tail) {
+ return 0;
+ }
+
+ data = rbuf[rbuf_tail];
+ rbuf_tail = (rbuf_tail + 1) % RBUF_SIZE;
+ return data;
+}
+
+// USART RX complete interrupt
+ISR(SERIAL_RX_VECT)
+{
+ uint8_t next = (rbuf_head + 1) % RBUF_SIZE;
+ if (next != rbuf_tail) {
+ rbuf[rbuf_head] = SERIAL_RX_DATA;
+ rbuf_head = next;
+ }
+}
diff --git a/protocol/serial.h b/protocol/serial.h
new file mode 100644
index 0000000000..93b9ee9225
--- /dev/null
+++ b/protocol/serial.h
@@ -0,0 +1,45 @@
+/*
+Copyright 2012 Jun WAKO <wakojun@gmail.com>
+
+This software is licensed with a Modified BSD License.
+All of this is supposed to be Free Software, Open Source, DFSG-free,
+GPL-compatible, and OK to use in both free and proprietary applications.
+Additions and corrections to this file are welcome.
+
+
+Redistribution and use in source and binary forms, with or without
+modification, are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright
+ notice, this list of conditions and the following disclaimer.
+
+* Redistributions in binary form must reproduce the above copyright
+ notice, this list of conditions and the following disclaimer in
+ the documentation and/or other materials provided with the
+ distribution.
+
+* Neither the name of the copyright holders nor the names of
+ contributors may be used to endorse or promote products derived
+ from this software without specific prior written permission.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+POSSIBILITY OF SUCH DAMAGE.
+*/
+
+#ifndef SERIAL_H
+#define SERIAL_H
+
+/* host role */
+void serial_init(void);
+uint8_t serial_recv(void);
+
+#endif