diff options
author | Jack Humbert <jack.humb@gmail.com> | 2015-10-27 14:52:18 -0400 |
---|---|---|
committer | Jack Humbert <jack.humb@gmail.com> | 2015-10-27 14:52:18 -0400 |
commit | d311fd8d1a0af3b767d26b520d399bf0db22f058 (patch) | |
tree | b9de5704143ac205b4e26222f9d7551e9b161924 /tmk_core/protocol/vusb/usbdrv/usbdrv.h | |
parent | a766918d5c48204375f4c207b30bbbf1389df14f (diff) | |
parent | 6f3141965e88c4ee0ebf7c18a243e4c2d9c5021b (diff) |
Merge pull request #34 from jackhumbert/tmk-master
merging from tmk, new_project script and template
Diffstat (limited to 'tmk_core/protocol/vusb/usbdrv/usbdrv.h')
-rw-r--r-- | tmk_core/protocol/vusb/usbdrv/usbdrv.h | 735 |
1 files changed, 735 insertions, 0 deletions
diff --git a/tmk_core/protocol/vusb/usbdrv/usbdrv.h b/tmk_core/protocol/vusb/usbdrv/usbdrv.h new file mode 100644 index 0000000000..42fe163720 --- /dev/null +++ b/tmk_core/protocol/vusb/usbdrv/usbdrv.h @@ -0,0 +1,735 @@ +/* Name: usbdrv.h + * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers + * Author: Christian Starkjohann + * Creation Date: 2004-12-29 + * Tabsize: 4 + * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH + * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) + * This Revision: $Id: usbdrv.h 793 2010-07-15 15:58:11Z cs $ + */ + +#ifndef __usbdrv_h_included__ +#define __usbdrv_h_included__ +#include "usbconfig.h" +#include "usbportability.h" + +/* +Hardware Prerequisites: +======================= +USB lines D+ and D- MUST be wired to the same I/O port. We recommend that D+ +triggers the interrupt (best achieved by using INT0 for D+), but it is also +possible to trigger the interrupt from D-. If D- is used, interrupts are also +triggered by SOF packets. D- requires a pull-up of 1.5k to +3.5V (and the +device must be powered at 3.5V) to identify as low-speed USB device. A +pull-down or pull-up of 1M SHOULD be connected from D+ to +3.5V to prevent +interference when no USB master is connected. If you use Zener diodes to limit +the voltage on D+ and D-, you MUST use a pull-down resistor, not a pull-up. +We use D+ as interrupt source and not D- because it does not trigger on +keep-alive and RESET states. If you want to count keep-alive events with +USB_COUNT_SOF, you MUST use D- as an interrupt source. + +As a compile time option, the 1.5k pull-up resistor on D- can be made +switchable to allow the device to disconnect at will. See the definition of +usbDeviceConnect() and usbDeviceDisconnect() further down in this file. + +Please adapt the values in usbconfig.h according to your hardware! + +The device MUST be clocked at exactly 12 MHz, 15 MHz, 16 MHz or 20 MHz +or at 12.8 MHz resp. 16.5 MHz +/- 1%. See usbconfig-prototype.h for details. + + +Limitations: +============ +Robustness with respect to communication errors: +The driver assumes error-free communication. It DOES check for errors in +the PID, but does NOT check bit stuffing errors, SE0 in middle of a byte, +token CRC (5 bit) and data CRC (16 bit). CRC checks can not be performed due +to timing constraints: We must start sending a reply within 7 bit times. +Bit stuffing and misplaced SE0 would have to be checked in real-time, but CPU +performance does not permit that. The driver does not check Data0/Data1 +toggling, but application software can implement the check. + +Input characteristics: +Since no differential receiver circuit is used, electrical interference +robustness may suffer. The driver samples only one of the data lines with +an ordinary I/O pin's input characteristics. However, since this is only a +low speed USB implementation and the specification allows for 8 times the +bit rate over the same hardware, we should be on the safe side. Even the spec +requires detection of asymmetric states at high bit rate for SE0 detection. + +Number of endpoints: +The driver supports the following endpoints: + +- Endpoint 0, the default control endpoint. +- Any number of interrupt- or bulk-out endpoints. The data is sent to + usbFunctionWriteOut() and USB_CFG_IMPLEMENT_FN_WRITEOUT must be defined + to 1 to activate this feature. The endpoint number can be found in the + global variable 'usbRxToken'. +- One default interrupt- or bulk-in endpoint. This endpoint is used for + interrupt- or bulk-in transfers which are not handled by any other endpoint. + You must define USB_CFG_HAVE_INTRIN_ENDPOINT in order to activate this + feature and call usbSetInterrupt() to send interrupt/bulk data. +- One additional interrupt- or bulk-in endpoint. This was endpoint 3 in + previous versions of this driver but can now be configured to any endpoint + number. You must define USB_CFG_HAVE_INTRIN_ENDPOINT3 in order to activate + this feature and call usbSetInterrupt3() to send interrupt/bulk data. The + endpoint number can be set with USB_CFG_EP3_NUMBER. + +Please note that the USB standard forbids bulk endpoints for low speed devices! +Most operating systems allow them anyway, but the AVR will spend 90% of the CPU +time in the USB interrupt polling for bulk data. + +Maximum data payload: +Data payload of control in and out transfers may be up to 254 bytes. In order +to accept payload data of out transfers, you need to implement +'usbFunctionWrite()'. + +USB Suspend Mode supply current: +The USB standard limits power consumption to 500uA when the bus is in suspend +mode. This is not a problem for self-powered devices since they don't need +bus power anyway. Bus-powered devices can achieve this only by putting the +CPU in sleep mode. The driver does not implement suspend handling by itself. +However, the application may implement activity monitoring and wakeup from +sleep. The host sends regular SE0 states on the bus to keep it active. These +SE0 states can be detected by using D- as the interrupt source. Define +USB_COUNT_SOF to 1 and use the global variable usbSofCount to check for bus +activity. + +Operation without an USB master: +The driver behaves neutral without connection to an USB master if D- reads +as 1. To avoid spurious interrupts, we recommend a high impedance (e.g. 1M) +pull-down or pull-up resistor on D+ (interrupt). If Zener diodes are used, +use a pull-down. If D- becomes statically 0, the driver may block in the +interrupt routine. + +Interrupt latency: +The application must ensure that the USB interrupt is not disabled for more +than 25 cycles (this is for 12 MHz, faster clocks allow longer latency). +This implies that all interrupt routines must either have the "ISR_NOBLOCK" +attribute set (see "avr/interrupt.h") or be written in assembler with "sei" +as the first instruction. + +Maximum interrupt duration / CPU cycle consumption: +The driver handles all USB communication during the interrupt service +routine. The routine will not return before an entire USB message is received +and the reply is sent. This may be up to ca. 1200 cycles @ 12 MHz (= 100us) if +the host conforms to the standard. The driver will consume CPU cycles for all +USB messages, even if they address another (low-speed) device on the same bus. + +*/ + +/* ------------------------------------------------------------------------- */ +/* --------------------------- Module Interface ---------------------------- */ +/* ------------------------------------------------------------------------- */ + +#define USBDRV_VERSION 20100715 +/* This define uniquely identifies a driver version. It is a decimal number + * constructed from the driver's release date in the form YYYYMMDD. If the + * driver's behavior or interface changes, you can use this constant to + * distinguish versions. If it is not defined, the driver's release date is + * older than 2006-01-25. + */ + + +#ifndef USB_PUBLIC +#define USB_PUBLIC +#endif +/* USB_PUBLIC is used as declaration attribute for all functions exported by + * the USB driver. The default is no attribute (see above). You may define it + * to static either in usbconfig.h or from the command line if you include + * usbdrv.c instead of linking against it. Including the C module of the driver + * directly in your code saves a couple of bytes in flash memory. + */ + +#ifndef __ASSEMBLER__ +#ifndef uchar +#define uchar unsigned char +#endif +#ifndef schar +#define schar signed char +#endif +/* shortcuts for well defined 8 bit integer types */ + +#if USB_CFG_LONG_TRANSFERS /* if more than 254 bytes transfer size required */ +# define usbMsgLen_t unsigned +#else +# define usbMsgLen_t uchar +#endif +/* usbMsgLen_t is the data type used for transfer lengths. By default, it is + * defined to uchar, allowing a maximum of 254 bytes (255 is reserved for + * USB_NO_MSG below). If the usbconfig.h defines USB_CFG_LONG_TRANSFERS to 1, + * a 16 bit data type is used, allowing up to 16384 bytes (the rest is used + * for flags in the descriptor configuration). + */ +#define USB_NO_MSG ((usbMsgLen_t)-1) /* constant meaning "no message" */ + +struct usbRequest; /* forward declaration */ + +USB_PUBLIC void usbInit(void); +/* This function must be called before interrupts are enabled and the main + * loop is entered. We exepct that the PORT and DDR bits for D+ and D- have + * not been changed from their default status (which is 0). If you have changed + * them, set both back to 0 (configure them as input with no internal pull-up). + */ +USB_PUBLIC void usbPoll(void); +/* This function must be called at regular intervals from the main loop. + * Maximum delay between calls is somewhat less than 50ms (USB timeout for + * accepting a Setup message). Otherwise the device will not be recognized. + * Please note that debug outputs through the UART take ~ 0.5ms per byte + * at 19200 bps. + */ +extern uchar *usbMsgPtr; +/* This variable may be used to pass transmit data to the driver from the + * implementation of usbFunctionWrite(). It is also used internally by the + * driver for standard control requests. + */ +USB_PUBLIC usbMsgLen_t usbFunctionSetup(uchar data[8]); +/* This function is called when the driver receives a SETUP transaction from + * the host which is not answered by the driver itself (in practice: class and + * vendor requests). All control transfers start with a SETUP transaction where + * the host communicates the parameters of the following (optional) data + * transfer. The SETUP data is available in the 'data' parameter which can + * (and should) be casted to 'usbRequest_t *' for a more user-friendly access + * to parameters. + * + * If the SETUP indicates a control-in transfer, you should provide the + * requested data to the driver. There are two ways to transfer this data: + * (1) Set the global pointer 'usbMsgPtr' to the base of the static RAM data + * block and return the length of the data in 'usbFunctionSetup()'. The driver + * will handle the rest. Or (2) return USB_NO_MSG in 'usbFunctionSetup()'. The + * driver will then call 'usbFunctionRead()' when data is needed. See the + * documentation for usbFunctionRead() for details. + * + * If the SETUP indicates a control-out transfer, the only way to receive the + * data from the host is through the 'usbFunctionWrite()' call. If you + * implement this function, you must return USB_NO_MSG in 'usbFunctionSetup()' + * to indicate that 'usbFunctionWrite()' should be used. See the documentation + * of this function for more information. If you just want to ignore the data + * sent by the host, return 0 in 'usbFunctionSetup()'. + * + * Note that calls to the functions usbFunctionRead() and usbFunctionWrite() + * are only done if enabled by the configuration in usbconfig.h. + */ +USB_PUBLIC usbMsgLen_t usbFunctionDescriptor(struct usbRequest *rq); +/* You need to implement this function ONLY if you provide USB descriptors at + * runtime (which is an expert feature). It is very similar to + * usbFunctionSetup() above, but it is called only to request USB descriptor + * data. See the documentation of usbFunctionSetup() above for more info. + */ +#if USB_CFG_HAVE_INTRIN_ENDPOINT +USB_PUBLIC void usbSetInterrupt(uchar *data, uchar len); +/* This function sets the message which will be sent during the next interrupt + * IN transfer. The message is copied to an internal buffer and must not exceed + * a length of 8 bytes. The message may be 0 bytes long just to indicate the + * interrupt status to the host. + * If you need to transfer more bytes, use a control read after the interrupt. + */ +#define usbInterruptIsReady() (usbTxLen1 & 0x10) +/* This macro indicates whether the last interrupt message has already been + * sent. If you set a new interrupt message before the old was sent, the + * message already buffered will be lost. + */ +#if USB_CFG_HAVE_INTRIN_ENDPOINT3 +USB_PUBLIC void usbSetInterrupt3(uchar *data, uchar len); +#define usbInterruptIsReady3() (usbTxLen3 & 0x10) +/* Same as above for endpoint 3 */ +#endif +#endif /* USB_CFG_HAVE_INTRIN_ENDPOINT */ +#if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH /* simplified interface for backward compatibility */ +#define usbHidReportDescriptor usbDescriptorHidReport +/* should be declared as: PROGMEM char usbHidReportDescriptor[]; */ +/* If you implement an HID device, you need to provide a report descriptor. + * The HID report descriptor syntax is a bit complex. If you understand how + * report descriptors are constructed, we recommend that you use the HID + * Descriptor Tool from usb.org, see http://www.usb.org/developers/hidpage/. + * Otherwise you should probably start with a working example. + */ +#endif /* USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH */ +#if USB_CFG_IMPLEMENT_FN_WRITE +USB_PUBLIC uchar usbFunctionWrite(uchar *data, uchar len); +/* This function is called by the driver to provide a control transfer's + * payload data (control-out). It is called in chunks of up to 8 bytes. The + * total count provided in the current control transfer can be obtained from + * the 'length' property in the setup data. If an error occurred during + * processing, return 0xff (== -1). The driver will answer the entire transfer + * with a STALL token in this case. If you have received the entire payload + * successfully, return 1. If you expect more data, return 0. If you don't + * know whether the host will send more data (you should know, the total is + * provided in the usbFunctionSetup() call!), return 1. + * NOTE: If you return 0xff for STALL, 'usbFunctionWrite()' may still be called + * for the remaining data. You must continue to return 0xff for STALL in these + * calls. + * In order to get usbFunctionWrite() called, define USB_CFG_IMPLEMENT_FN_WRITE + * to 1 in usbconfig.h and return 0xff in usbFunctionSetup().. + */ +#endif /* USB_CFG_IMPLEMENT_FN_WRITE */ +#if USB_CFG_IMPLEMENT_FN_READ +USB_PUBLIC uchar usbFunctionRead(uchar *data, uchar len); +/* This function is called by the driver to ask the application for a control + * transfer's payload data (control-in). It is called in chunks of up to 8 + * bytes each. You should copy the data to the location given by 'data' and + * return the actual number of bytes copied. If you return less than requested, + * the control-in transfer is terminated. If you return 0xff, the driver aborts + * the transfer with a STALL token. + * In order to get usbFunctionRead() called, define USB_CFG_IMPLEMENT_FN_READ + * to 1 in usbconfig.h and return 0xff in usbFunctionSetup().. + */ +#endif /* USB_CFG_IMPLEMENT_FN_READ */ + +extern uchar usbRxToken; /* may be used in usbFunctionWriteOut() below */ +#if USB_CFG_IMPLEMENT_FN_WRITEOUT +USB_PUBLIC void usbFunctionWriteOut(uchar *data, uchar len); +/* This function is called by the driver when data is received on an interrupt- + * or bulk-out endpoint. The endpoint number can be found in the global + * variable usbRxToken. You must define USB_CFG_IMPLEMENT_FN_WRITEOUT to 1 in + * usbconfig.h to get this function called. + */ +#endif /* USB_CFG_IMPLEMENT_FN_WRITEOUT */ +#ifdef USB_CFG_PULLUP_IOPORTNAME +#define usbDeviceConnect() ((USB_PULLUP_DDR |= (1<<USB_CFG_PULLUP_BIT)), \ + (USB_PULLUP_OUT |= (1<<USB_CFG_PULLUP_BIT))) +#define usbDeviceDisconnect() ((USB_PULLUP_DDR &= ~(1<<USB_CFG_PULLUP_BIT)), \ + (USB_PULLUP_OUT &= ~(1<<USB_CFG_PULLUP_BIT))) +#else /* USB_CFG_PULLUP_IOPORTNAME */ +#define usbDeviceConnect() (USBDDR &= ~(1<<USBMINUS)) +#define usbDeviceDisconnect() (USBDDR |= (1<<USBMINUS)) +#endif /* USB_CFG_PULLUP_IOPORTNAME */ +/* The macros usbDeviceConnect() and usbDeviceDisconnect() (intended to look + * like a function) connect resp. disconnect the device from the host's USB. + * If the constants USB_CFG_PULLUP_IOPORT and USB_CFG_PULLUP_BIT are defined + * in usbconfig.h, a disconnect consists of removing the pull-up resisitor + * from D-, otherwise the disconnect is done by brute-force pulling D- to GND. + * This does not conform to the spec, but it works. + * Please note that the USB interrupt must be disabled while the device is + * in disconnected state, or the interrupt handler will hang! You can either + * turn off the USB interrupt selectively with + * USB_INTR_ENABLE &= ~(1 << USB_INTR_ENABLE_BIT) + * or use cli() to disable interrupts globally. + */ +extern unsigned usbCrc16(unsigned data, uchar len); +#define usbCrc16(data, len) usbCrc16((unsigned)(data), len) +/* This function calculates the binary complement of the data CRC used in + * USB data packets. The value is used to build raw transmit packets. + * You may want to use this function for data checksums or to verify received + * data. We enforce 16 bit calling conventions for compatibility with IAR's + * tiny memory model. + */ +extern unsigned usbCrc16Append(unsigned data, uchar len); +#define usbCrc16Append(data, len) usbCrc16Append((unsigned)(data), len) +/* This function is equivalent to usbCrc16() above, except that it appends + * the 2 bytes CRC (lowbyte first) in the 'data' buffer after reading 'len' + * bytes. + */ +#if USB_CFG_HAVE_MEASURE_FRAME_LENGTH +extern unsigned usbMeasureFrameLength(void); +/* This function MUST be called IMMEDIATELY AFTER USB reset and measures 1/7 of + * the number of CPU cycles during one USB frame minus one low speed bit + * length. In other words: return value = 1499 * (F_CPU / 10.5 MHz) + * Since this is a busy wait, you MUST disable all interrupts with cli() before + * calling this function. + * This can be used to calibrate the AVR's RC oscillator. + */ +#endif +extern uchar usbConfiguration; +/* This value contains the current configuration set by the host. The driver + * allows setting and querying of this variable with the USB SET_CONFIGURATION + * and GET_CONFIGURATION requests, but does not use it otherwise. + * You may want to reflect the "configured" status with a LED on the device or + * switch on high power parts of the circuit only if the device is configured. + */ +#if USB_COUNT_SOF +extern volatile uchar usbSofCount; +/* This variable is incremented on every SOF packet. It is only available if + * the macro USB_COUNT_SOF is defined to a value != 0. + */ +#endif +#if USB_CFG_CHECK_DATA_TOGGLING +extern uchar usbCurrentDataToken; +/* This variable can be checked in usbFunctionWrite() and usbFunctionWriteOut() + * to ignore duplicate packets. + */ +#endif + +#define USB_STRING_DESCRIPTOR_HEADER(stringLength) ((2*(stringLength)+2) | (3<<8)) +/* This macro builds a descriptor header for a string descriptor given the + * string's length. See usbdrv.c for an example how to use it. + */ +#if USB_CFG_HAVE_FLOWCONTROL +extern volatile schar usbRxLen; +#define usbDisableAllRequests() usbRxLen = -1 +/* Must be called from usbFunctionWrite(). This macro disables all data input + * from the USB interface. Requests from the host are answered with a NAK + * while they are disabled. + */ +#define usbEnableAllRequests() usbRxLen = 0 +/* May only be called if requests are disabled. This macro enables input from + * the USB interface after it has been disabled with usbDisableAllRequests(). + */ +#define usbAllRequestsAreDisabled() (usbRxLen < 0) +/* Use this macro to find out whether requests are disabled. It may be needed + * to ensure that usbEnableAllRequests() is never called when requests are + * enabled. + */ +#endif + +#define USB_SET_DATATOKEN1(token) usbTxBuf1[0] = token +#define USB_SET_DATATOKEN3(token) usbTxBuf3[0] = token +/* These two macros can be used by application software to reset data toggling + * for interrupt-in endpoints 1 and 3. Since the token is toggled BEFORE + * sending data, you must set the opposite value of the token which should come + * first. + */ + +#endif /* __ASSEMBLER__ */ + + +/* ------------------------------------------------------------------------- */ +/* ----------------- Definitions for Descriptor Properties ----------------- */ +/* ------------------------------------------------------------------------- */ +/* This is advanced stuff. See usbconfig-prototype.h for more information + * about the various methods to define USB descriptors. If you do nothing, + * the default descriptors will be used. + */ +#define USB_PROP_IS_DYNAMIC (1 << 14) +/* If this property is set for a descriptor, usbFunctionDescriptor() will be + * used to obtain the particular descriptor. Data directly returned via + * usbMsgPtr are FLASH data by default, combine (OR) with USB_PROP_IS_RAM to + * return RAM data. + */ +#define USB_PROP_IS_RAM (1 << 15) +/* If this property is set for a descriptor, the data is read from RAM + * memory instead of Flash. The property is used for all methods to provide + * external descriptors. + */ +#define USB_PROP_LENGTH(len) ((len) & 0x3fff) +/* If a static external descriptor is used, this is the total length of the + * descriptor in bytes. + */ + +/* all descriptors which may have properties: */ +#ifndef USB_CFG_DESCR_PROPS_DEVICE +#define USB_CFG_DESCR_PROPS_DEVICE 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_CONFIGURATION +#define USB_CFG_DESCR_PROPS_CONFIGURATION 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_STRINGS +#define USB_CFG_DESCR_PROPS_STRINGS 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_STRING_0 +#define USB_CFG_DESCR_PROPS_STRING_0 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_STRING_VENDOR +#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_STRING_PRODUCT +#define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER +#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0 +#endif +#ifndef USB_CFG_DESCR_PROPS_HID +#define USB_CFG_DESCR_PROPS_HID 0 +#endif +#if !(USB_CFG_DESCR_PROPS_HID_REPORT) +# undef USB_CFG_DESCR_PROPS_HID_REPORT +# if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH /* do some backward compatibility tricks */ +# define USB_CFG_DESCR_PROPS_HID_REPORT USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH +# else +# define USB_CFG_DESCR_PROPS_HID_REPORT 0 +# endif +#endif +#ifndef USB_CFG_DESCR_PROPS_UNKNOWN +#define USB_CFG_DESCR_PROPS_UNKNOWN 0 +#endif + +/* ------------------ forward declaration of descriptors ------------------- */ +/* If you use external static descriptors, they must be stored in global + * arrays as declared below: + */ +#ifndef __ASSEMBLER__ +extern +#if !(USB_CFG_DESCR_PROPS_DEVICE & USB_PROP_IS_RAM) +PROGMEM +#endif +const char usbDescriptorDevice[]; + +extern +#if !(USB_CFG_DESCR_PROPS_CONFIGURATION & USB_PROP_IS_RAM) +PROGMEM +#endif +const char usbDescriptorConfiguration[]; + +extern +#if !(USB_CFG_DESCR_PROPS_HID_REPORT & USB_PROP_IS_RAM) +PROGMEM +#endif +const char usbDescriptorHidReport[]; + +extern +#if !(USB_CFG_DESCR_PROPS_STRING_0 & USB_PROP_IS_RAM) +PROGMEM +#endif +const char usbDescriptorString0[]; + +extern +#if !(USB_CFG_DESCR_PROPS_STRING_VENDOR & USB_PROP_IS_RAM) +PROGMEM +#endif +const int usbDescriptorStringVendor[]; + +extern +#if !(USB_CFG_DESCR_PROPS_STRING_PRODUCT & USB_PROP_IS_RAM) +PROGMEM +#endif +const int usbDescriptorStringDevice[]; + +extern +#if !(USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER & USB_PROP_IS_RAM) +PROGMEM +#endif +const int usbDescriptorStringSerialNumber[]; + +#endif /* __ASSEMBLER__ */ + +/* ------------------------------------------------------------------------- */ +/* ------------------------ General Purpose Macros ------------------------- */ +/* ------------------------------------------------------------------------- */ + +#define USB_CONCAT(a, b) a ## b +#define USB_CONCAT_EXPANDED(a, b) USB_CONCAT(a, b) + +#define USB_OUTPORT(name) USB_CONCAT(PORT, name) +#define USB_INPORT(name) USB_CONCAT(PIN, name) +#define USB_DDRPORT(name) USB_CONCAT(DDR, name) +/* The double-define trick above lets us concatenate strings which are + * defined by macros. + */ + +/* ------------------------------------------------------------------------- */ +/* ------------------------- Constant definitions -------------------------- */ +/* ------------------------------------------------------------------------- */ + +#if !defined __ASSEMBLER__ && (!defined USB_CFG_VENDOR_ID || !defined USB_CFG_DEVICE_ID) +#warning "You should define USB_CFG_VENDOR_ID and USB_CFG_DEVICE_ID in usbconfig.h" +/* If the user has not defined IDs, we default to obdev's free IDs. + * See USB-IDs-for-free.txt for details. + */ +#endif + +/* make sure we have a VID and PID defined, byte order is lowbyte, highbyte */ +#ifndef USB_CFG_VENDOR_ID +# define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */ +#endif + +#ifndef USB_CFG_DEVICE_ID +# if USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH +# define USB_CFG_DEVICE_ID 0xdf, 0x05 /* = 0x5df = 1503, shared PID for HIDs */ +# elif USB_CFG_INTERFACE_CLASS == 2 +# define USB_CFG_DEVICE_ID 0xe1, 0x05 /* = 0x5e1 = 1505, shared PID for CDC Modems */ +# else +# define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x5dc = 1500, obdev's free PID */ +# endif +#endif + +/* Derive Output, Input and DataDirection ports from port names */ +#ifndef USB_CFG_IOPORTNAME +#error "You must define USB_CFG_IOPORTNAME in usbconfig.h, see usbconfig-prototype.h" +#endif + +#define USBOUT USB_OUTPORT(USB_CFG_IOPORTNAME) +#define USB_PULLUP_OUT USB_OUTPORT(USB_CFG_PULLUP_IOPORTNAME) +#define USBIN USB_INPORT(USB_CFG_IOPORTNAME) +#define USBDDR USB_DDRPORT(USB_CFG_IOPORTNAME) +#define USB_PULLUP_DDR USB_DDRPORT(USB_CFG_PULLUP_IOPORTNAME) + +#define USBMINUS USB_CFG_DMINUS_BIT +#define USBPLUS USB_CFG_DPLUS_BIT +#define USBIDLE (1<<USB_CFG_DMINUS_BIT) /* value representing J state */ +#define USBMASK ((1<<USB_CFG_DPLUS_BIT) | (1<<USB_CFG_DMINUS_BIT)) /* mask for USB I/O bits */ + +/* defines for backward compatibility with older driver versions: */ +#define USB_CFG_IOPORT USB_OUTPORT(USB_CFG_IOPORTNAME) +#ifdef USB_CFG_PULLUP_IOPORTNAME +#define USB_CFG_PULLUP_IOPORT USB_OUTPORT(USB_CFG_PULLUP_IOPORTNAME) +#endif + +#ifndef USB_CFG_EP3_NUMBER /* if not defined in usbconfig.h */ +#define USB_CFG_EP3_NUMBER 3 +#endif + +#ifndef USB_CFG_HAVE_INTRIN_ENDPOINT3 +#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0 +#endif + +#define USB_BUFSIZE 11 /* PID, 8 bytes data, 2 bytes CRC */ + +/* ----- Try to find registers and bits responsible for ext interrupt 0 ----- */ + +#ifndef USB_INTR_CFG /* allow user to override our default */ +# if defined EICRA +# define USB_INTR_CFG EICRA +# else +# define USB_INTR_CFG MCUCR +# endif +#endif +#ifndef USB_INTR_CFG_SET /* allow user to override our default */ +# if defined(USB_COUNT_SOF) || defined(USB_SOF_HOOK) +# define USB_INTR_CFG_SET (1 << ISC01) /* cfg for falling edge */ + /* If any SOF logic is used, the interrupt must be wired to D- where + * we better trigger on falling edge + */ +# else +# define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) /* cfg for rising edge */ +# endif +#endif +#ifndef USB_INTR_CFG_CLR /* allow user to override our default */ +# define USB_INTR_CFG_CLR 0 /* no bits to clear */ +#endif + +#ifndef USB_INTR_ENABLE /* allow user to override our default */ +# if defined GIMSK +# define USB_INTR_ENABLE GIMSK +# elif defined EIMSK +# define USB_INTR_ENABLE EIMSK +# else +# define USB_INTR_ENABLE GICR +# endif +#endif +#ifndef USB_INTR_ENABLE_BIT /* allow user to override our default */ +# define USB_INTR_ENABLE_BIT INT0 +#endif + +#ifndef USB_INTR_PENDING /* allow user to override our default */ +# if defined EIFR +# define USB_INTR_PENDING EIFR +# else +# define USB_INTR_PENDING GIFR +# endif +#endif +#ifndef USB_INTR_PENDING_BIT /* allow user to override our default */ +# define USB_INTR_PENDING_BIT INTF0 +#endif + +/* +The defines above don't work for the following chips +at90c8534: no ISC0?, no PORTB, can't find a data sheet +at86rf401: no PORTB, no MCUCR etc, low clock rate +atmega103: no ISC0? (maybe omission in header, can't find data sheet) +atmega603: not defined in avr-libc +at43usb320, at43usb355, at76c711: have USB anyway +at94k: is different... + +at90s1200, attiny11, attiny12, attiny15, attiny28: these have no RAM +*/ + +/* ------------------------------------------------------------------------- */ +/* ----------------- USB Specification Constants and Types ----------------- */ +/* ------------------------------------------------------------------------- */ + +/* USB Token values */ +#define USBPID_SETUP 0x2d +#define USBPID_OUT 0xe1 +#define USBPID_IN 0x69 +#define USBPID_DATA0 0xc3 +#define USBPID_DATA1 0x4b + +#define USBPID_ACK 0xd2 +#define USBPID_NAK 0x5a +#define USBPID_STALL 0x1e + +#ifndef USB_INITIAL_DATATOKEN +#define USB_INITIAL_DATATOKEN USBPID_DATA1 +#endif + +#ifndef __ASSEMBLER__ + +typedef struct usbTxStatus{ + volatile uchar len; + uchar buffer[USB_BUFSIZE]; +}usbTxStatus_t; + +extern usbTxStatus_t usbTxStatus1, usbTxStatus3; +#define usbTxLen1 usbTxStatus1.len +#define usbTxBuf1 usbTxStatus1.buffer +#define usbTxLen3 usbTxStatus3.len +#define usbTxBuf3 usbTxStatus3.buffer + + +typedef union usbWord{ + unsigned word; + uchar bytes[2]; +}usbWord_t; + +typedef struct usbRequest{ + uchar bmRequestType; + uchar bRequest; + usbWord_t wValue; + usbWord_t wIndex; + usbWord_t wLength; +}usbRequest_t; +/* This structure matches the 8 byte setup request */ +#endif + +/* bmRequestType field in USB setup: + * d t t r r r r r, where + * d ..... direction: 0=host->device, 1=device->host + * t ..... type: 0=standard, 1=class, 2=vendor, 3=reserved + * r ..... recipient: 0=device, 1=interface, 2=endpoint, 3=other + */ + +/* USB setup recipient values */ +#define USBRQ_RCPT_MASK 0x1f +#define USBRQ_RCPT_DEVICE 0 +#define USBRQ_RCPT_INTERFACE 1 +#define USBRQ_RCPT_ENDPOINT 2 + +/* USB request type values */ +#define USBRQ_TYPE_MASK 0x60 +#define USBRQ_TYPE_STANDARD (0<<5) +#define USBRQ_TYPE_CLASS (1<<5) +#define USBRQ_TYPE_VENDOR (2<<5) + +/* USB direction values: */ +#define USBRQ_DIR_MASK 0x80 +#define USBRQ_DIR_HOST_TO_DEVICE (0<<7) +#define USBRQ_DIR_DEVICE_TO_HOST (1<<7) + +/* USB Standard Requests */ +#define USBRQ_GET_STATUS 0 +#define USBRQ_CLEAR_FEATURE 1 +#define USBRQ_SET_FEATURE 3 +#define USBRQ_SET_ADDRESS 5 +#define USBRQ_GET_DESCRIPTOR 6 +#define USBRQ_SET_DESCRIPTOR 7 +#define USBRQ_GET_CONFIGURATION 8 +#define USBRQ_SET_CONFIGURATION 9 +#define USBRQ_GET_INTERFACE 10 +#define USBRQ_SET_INTERFACE 11 +#define USBRQ_SYNCH_FRAME 12 + +/* USB descriptor constants */ +#define USBDESCR_DEVICE 1 +#define USBDESCR_CONFIG 2 +#define USBDESCR_STRING 3 +#define USBDESCR_INTERFACE 4 +#define USBDESCR_ENDPOINT 5 +#define USBDESCR_HID 0x21 +#define USBDESCR_HID_REPORT 0x22 +#define USBDESCR_HID_PHYS 0x23 + +//#define USBATTR_BUSPOWER 0x80 // USB 1.1 does not define this value any more +#define USBATTR_SELFPOWER 0x40 +#define USBATTR_REMOTEWAKE 0x20 + +/* USB HID Requests */ +#define USBRQ_HID_GET_REPORT 0x01 +#define USBRQ_HID_GET_IDLE 0x02 +#define USBRQ_HID_GET_PROTOCOL 0x03 +#define USBRQ_HID_SET_REPORT 0x09 +#define USBRQ_HID_SET_IDLE 0x0a +#define USBRQ_HID_SET_PROTOCOL 0x0b + +/* ------------------------------------------------------------------------- */ + +#endif /* __usbdrv_h_included__ */ |