Made directories for keyboard and converter projects.

26 files changed, 0 insertions, 1695 deletions

diff --git a/hhkb/Makefile.iwrap b/hhkb/Makefile.iwrap
deleted file mode 100644
index d922b0f501..0000000000
--- a/hhkb/Makefile.iwrap
+++ /dev/null
@@ -1,93 +0,0 @@
-#
-# Makefile for iWRAP
-#
-
-
-# Target file name (without extension).
-TARGET = hhkb_iwrap
-
-# Directory common source filess exist
-TOP_DIR = ..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =	main.c \
-	keymap.c \
-	matrix.c \
-	led.c
-
-CONFIG_H = config_iwrap.h
-
-
-# V-USB debug level: To use ps2_usart.c level must be 0
-# ps2_usart.c requires USART to receive PS/2 signal.
-OPT_DEFS = -DDEBUG_LEVEL=0
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-MCU = atmega168p
-# avrdude doesn't know atmega168p
-AVRDUDE_MCU = atmega168
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 12000000
-
-
-# Build Options
-#   comment out to disable the options.
-#
-MOUSEKEY_ENABLE = yes	# Mouse keys
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-#NKRO_ENABLE = yes	# USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-AVRDUDE = avrdude
-# Type: avrdude -c ? to get a full listing.
-AVRDUDE_PROGRAMMER = usbasp
-AVRDUDE_PORT =
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
-
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-
-# Increase verbosity level.  Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
-
-#AVRDUDE_FLAGS = -p $(AVRDUDE_MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS = -p $(AVRDUDE_MCU) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
-
-PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-
-
-
-# Search Path
-VPATH = $(TARGET_DIR)
-
-include $(TOP_DIR)/protocol/iwrap.mk
-# To be swatchable btween Bluetooth and USB. Comment out if you don't need USB.
-include $(TOP_DIR)/protocol/vusb.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
diff --git a/hhkb/Makefile.pjrc b/hhkb/Makefile.pjrc
deleted file mode 100644
index 28b6b589dd..0000000000
--- a/hhkb/Makefile.pjrc
+++ /dev/null
@@ -1,60 +0,0 @@
-#
-# Makefile for PJRC Teensy
-#
-
-
-# Target file name (without extension).
-TARGET = hhkb_pjrc
-
-# Directory common source filess exist
-TOP_DIR = ..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =	main.c \
-	keymap.c \
-	matrix.c \
-	led.c
-
-CONFIG_H = config_pjrc.h
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-#MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-MCU = at90usb1286      # Teensy++ 2.0
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 16000000
-
-
-# Build Options
-#   comment out to disable the options.
-MOUSEKEY_ENABLE = yes	# Mouse keys
-#PS2_MOUSE_ENABLE = yes	# PS/2 mouse(TrackPoint) support
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-NKRO_ENABLE = yes	# USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
-
-
-
-# Search Path
-VPATH = $(TARGET_DIR)
-
-include $(TOP_DIR)/protocol/pjrc.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
diff --git a/hhkb/Makefile.vusb b/hhkb/Makefile.vusb
deleted file mode 100644
index 734b73a029..0000000000
--- a/hhkb/Makefile.vusb
+++ /dev/null
@@ -1,91 +0,0 @@
-#
-# Makefile for V-USB
-#
-
-
-# Target file name (without extension).
-TARGET = hhkb_vusb
-
-# Directory common source filess exist
-TOP_DIR = ..
-
-# Directory keyboard dependent files exist
-TARGET_DIR = .
-
-# keyboard dependent files
-SRC =	main.c \
-	keymap.c \
-	matrix.c \
-	led.c
-
-CONFIG_H = config_vusb.h
-
-
-# V-USB debug level: To use ps2_usart.c level must be 0
-# ps2_usart.c requires USART to receive PS/2 signal.
-OPT_DEFS = -DDEBUG_LEVEL=0
-
-
-# MCU name, you MUST set this to match the board you are using
-# type "make clean" after changing this, so all files will be rebuilt
-MCU = atmega328p
-# avrdude doesn't know atmega168p
-AVRDUDE_MCU = $(MCU)
-
-
-# Processor frequency.
-#   Normally the first thing your program should do is set the clock prescaler,
-#   so your program will run at the correct speed.  You should also set this
-#   variable to same clock speed.  The _delay_ms() macro uses this, and many
-#   examples use this variable to calculate timings.  Do not add a "UL" here.
-F_CPU = 12000000
-
-
-# Build Options
-#   comment out to disable the options.
-#
-MOUSEKEY_ENABLE = yes	# Mouse keys
-EXTRAKEY_ENABLE = yes	# Audio control and System control
-#NKRO_ENABLE = yes	# USB Nkey Rollover
-
-
-
-#---------------- Programming Options --------------------------
-AVRDUDE = avrdude
-# Type: avrdude -c ? to get a full listing.
-AVRDUDE_PROGRAMMER = usbasp
-AVRDUDE_PORT =
-AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex
-#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep
-
-# Uncomment the following if you want avrdude's erase cycle counter.
-# Note that this counter needs to be initialized first using -Yn,
-# see avrdude manual.
-#AVRDUDE_ERASE_COUNTER = -y
-
-# Uncomment the following if you do /not/ wish a verification to be
-# performed after programming the device.
-#AVRDUDE_NO_VERIFY = -V
-
-# Increase verbosity level.  Please use this when submitting bug
-# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 
-# to submit bug reports.
-#AVRDUDE_VERBOSE = -v -v
-
-#AVRDUDE_FLAGS = -p $(AVRDUDE_MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS = -p $(AVRDUDE_MCU) -c $(AVRDUDE_PROGRAMMER)
-AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)
-AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)
-AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)
-
-PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)
-
-
-
-# Search Path
-VPATH = $(TARGET_DIR)
-
-include $(TOP_DIR)/protocol/vusb.mk
-include $(TOP_DIR)/protocol.mk
-include $(TOP_DIR)/common.mk
-include $(TOP_DIR)/rules.mk
diff --git a/hhkb/README b/hhkb/README
deleted file mode 100644
index 65f7dcab5a..0000000000
--- a/hhkb/README
+++ /dev/null
@@ -1,151 +0,0 @@
-Alternative Controller for HHKB
-===============================
-
-Feature
--------
-- Mouse Keys
-- NKRO on USB(PJRC Tennsy only)
-- Keymap Layers
-
-
-Customize Keymap
-----------------
-see keymap.c.
-
-
-
-Build
-=====
-PJRC Teensy
------------
-0. Edit matrix.c.
-    adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
-1. Define macros in config_pjrc.h.(Optional)
-    VENDOR_ID, PRODUCT_ID and string descriptor.
-    IS_COMMAND
-2. Edit Makefile for MCU setting and build options.
-    MCU, F_CPU
-    MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, NKRO_ENABLE
-3. Build hex file.
-    $ make -f Makefile.pjrc
-4. Program MCU.
-    $  make -f Makefile.pjrc program
-
-
-V-USB
------
-0. Edit matrix.c and usbconfig.h.
-    adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
-    define macros for V-USB in usbconfig.h.
-1. Define macros in config_vusb.h.(Optional)
-    IS_COMMAND
-2. Edit Makefile.vusb for MCU setting and build options.
-    MCU, F_CPU
-    MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
-3. Build hex file.
-    $ make -f Makefile.vusb
-4. Program MCU.
-    $  make -f Makefile.vusb program
-
-    Using a bootloader to program for convenience is recommended.
-    Once program this V-USB bootloader at first, you can program MCU without
-    extra programmer. You should have reset switch to start up as bootloader
-    mode in this case.
-    USBaspLoader:
-    http://www.obdev.at/products/vusb/usbasploader.html
-
-
-iWRAP
------
-0. Edit matrix.c and usbconfig.h.
-    adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
-    define macros for V-USB in usbconfig.h.
-1. Define macros in config_iwrap.h.(Optional)
-    IS_COMMAND
-2. Edit Makefile.iwrap for MCU setting and build options.
-    MCU, F_CPU
-    MOUSEKEY_ENABLE, EXTRAKEY_ENABLE
-3. Build hex file.
-    $ make -f Makefile.iwrap
-4. Program MCU.
-    $  make -f Makefile.iwrap program
-
-
-
-Hardware
-========
-PJRC Teensy
------------
-                        +---------------+
-                        |   Teensy++    |
-                        |               |
-                        |               |        HHKB
-                        |               |        ~~~~
-                        |          PB0-2|------->ROW(6-8)
-                        |          PB3-5|------->COL(9-11)
-                        |            PB6|------->ENABLE(12)
-                        |            PE6|<-------KEY(4)
-                        |            PE7|------->PREV(5)
-                        |               |
-                        |               |
-                        |               |
-                        +---------------+
-
-
-V-USB
------
-                +---+   +---------------+
-USB            GND  |   |   ATmega168   |
-~~~                 C3  |               |
-5V <-------+--------+---|Vcc,AVCC       |        HHKB
-           R1           |               |        ~~~~
-D- <----+--+-----R2-----|INT1      PB2-4|------->ROW(6-8)
-D+ <----|---+----R3-----|INT0      PC0-2|------->COL(9-11)
-        Z1  Z2          |            PC3|------->ENABLE(12)
-GND<----+---+-----------|GND         PB0|<-------KEY(4)
-                        |            PB1|------->PREV(5)
-                        |               |
-            GND+-C2--+--|XTAL1       RXD|------->Debug Console
-                     X1 |            TXD|<-------Debug Console
-            GND+-C3--+--|XTAL2       RST|---SW--+GND
-                        +---------------+
-R1:     1.5K Ohm
-R2,R3:  68 Ohm
-Z1,Z2:  Zener 3.6V
-C1,C2:  22pF
-C3:     0.1uF
-X1:     Crystal 20MHz(16MHz/12MHz)
-SW:     Push Switch(Optional for bootloader)
-
-
-iWRAP
------
-                        +---------------+        WT12
-              5V        |   ATmega168   | 5V/3.3V~~~~
-              +-----+---|Vcc,AVCC    PC4|---/--->iWRAP(RxD)
-USB           |     C3  |            PC5|<--/----iWRAP(TxD)
-~~~           |     +   |               | 
-5V <--BATT    +    GND  |               |        HHKB
-              R1        |               |        ~~~~
-D- <----+-----+--R2-----|INT1      PB2-4|------->ROW(6-8)
-D+ <----|---+----R3-----|INT0      PC0-2|------->COL(9-11)
-        Z1  Z2          |            PC3|------->ENABLE(12)
-GND<----+---+-----------|GND         PB0|<-------KEY(4)
-                        |            PB1|------->PREV(5)
-                        |               |
-            GND+-C2--+--|XTAL1       RXD|------->Debug Console
-                     X1 |            TXD|<-------Debug Console
-            GND+-C3--+--|XTAL2       RST|---SW--+GND
-                        +---------------+
-
-R1:     1.5K Ohm
-R2,R3:  68 Ohm
-Z1,Z2:  Zener 3.6V
-C1,C2:  22pF
-C3:     0.1uF
-X1:     Crystal 12MHz
-SW:     Push Switch(Optional)
-BATT:   Li-Po Battery, Battery Charger and Voltage Regulator(5V and 3.3V).
-
-
-EOF
diff --git a/hhkb/config_iwrap.h b/hhkb/config_iwrap.h
deleted file mode 100644
index 80ab64398b..0000000000
--- a/hhkb/config_iwrap.h
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0xBEEA
-// TODO: share these strings with usbconfig.h
-// Edit usbconfig.h to change these.
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         HHKB mod
-#define DESCRIPTION     t.m.k. keyboard firmware for HHKB mod
-
-
-/* matrix size */
-#define MATRIX_ROWS 8
-#define MATRIX_COLS 8
-
-
-/* key combination for command */
-#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_RSHIFT))) 
-
-/* mouse keys */
-#ifdef MOUSEKEY_ENABLE
-#   define MOUSEKEY_DELAY_TIME 255
-#endif
-
-/* pins for Software UART */
-#define SUART_IN_PIN    PINC
-#define SUART_IN_BIT    5
-#define SUART_OUT_PORT  PORTC
-#define SUART_OUT_BIT   4
-
-
-#define DEBUG_LED 1
-#define DEBUG_LED_CONFIG    (DDRD |= (1<<4))
-#define DEBUG_LED_OFF       (PORTD |= (1<<4))
-#define DEBUG_LED_ON        (PORTD &= ~(1<<4))
-
-#endif
diff --git a/hhkb/config_pjrc.h b/hhkb/config_pjrc.h
deleted file mode 100644
index fffe3522c7..0000000000
--- a/hhkb/config_pjrc.h
+++ /dev/null
@@ -1,62 +0,0 @@
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-/* controller configuration */
-#include "controller_teensy.h"
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0xCAFE
-#define DEVICE_VER      0x0101
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         HHKB mod
-#define DESCRIPTION     t.m.k. keyboard firmware for HHKB mod
-
-
-/* matrix size */
-#define MATRIX_ROWS 8
-#define MATRIX_COLS 8
-/* define if matrix has ghost */
-//#define MATRIX_HAS_GHOST
-
-
-/* key combination for command */
-#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_RSHIFT))) 
-
-/* mouse keys */
-#ifdef MOUSEKEY_ENABLE
-#   define MOUSEKEY_DELAY_TIME 192
-#endif
-
-
-/* PS/2 mouse */
-#ifdef PS2_MOUSE_ENABLE
-/*
-#   define PS2_CLOCK_PORT  PORTF
-#   define PS2_CLOCK_PIN   PINF
-#   define PS2_CLOCK_DDR   DDRF
-#   define PS2_CLOCK_BIT   0
-#   define PS2_DATA_PORT   PORTF
-#   define PS2_DATA_PIN    PINF
-#   define PS2_DATA_DDR    DDRF
-#   define PS2_DATA_BIT    1
-*/
-#endif
-
-#endif
diff --git a/hhkb/config_vusb.h b/hhkb/config_vusb.h
deleted file mode 100644
index 268644849e..0000000000
--- a/hhkb/config_vusb.h
+++ /dev/null
@@ -1,49 +0,0 @@
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#ifndef CONFIG_H
-#define CONFIG_H
-
-#define VENDOR_ID       0xFEED
-#define PRODUCT_ID      0xC0FE
-// TODO: share these strings with usbconfig.h
-// Edit usbconfig.h to change these.
-#define MANUFACTURER    t.m.k.
-#define PRODUCT         HHKB mod
-#define DESCRIPTION     t.m.k. keyboard firmware for HHKB mod
-
-
-/* matrix size */
-#define MATRIX_ROWS 8
-#define MATRIX_COLS 8
-
-
-/* key combination for command */
-#define IS_COMMAND() (keyboard_report->mods == (MOD_BIT(KB_LSHIFT) | MOD_BIT(KB_RSHIFT))) 
-
-/* mouse keys */
-#ifdef MOUSEKEY_ENABLE
-#   define MOUSEKEY_DELAY_TIME 255
-#endif
-
-
-#define DEBUG_LED 1
-#define DEBUG_LED_CONFIG    (DDRD |= (1<<4))
-#define DEBUG_LED_OFF       (PORTD |= (1<<4))
-#define DEBUG_LED_ON        (PORTD &= ~(1<<4))
-
-#endif
diff --git a/hhkb/doc/Bluetooth.txt b/hhkb/doc/Bluetooth.txt
deleted file mode 100644
index b27f197006..0000000000
--- a/hhkb/doc/Bluetooth.txt
+++ /dev/null
@@ -1,4 +0,0 @@
-HHKB Bluetooth mod
-==================
-See this article:
-http://geekhack.org/showwiki.php?title=Island:20851
diff --git a/hhkb/doc/Bluetooth_img/.picasa.ini b/hhkb/doc/Bluetooth_img/.picasa.ini
deleted file mode 100755
index f6a4f60674..0000000000
--- a/hhkb/doc/Bluetooth_img/.picasa.ini
+++ /dev/null
@@ -1,2 +0,0 @@
-[Picasa]

-name=Bluetooth_img

diff --git a/hhkb/doc/Bluetooth_img/BT_circuit.jpg b/hhkb/doc/Bluetooth_img/BT_circuit.jpg
deleted file mode 100644
index 2e5a25e81e..0000000000
--- a/hhkb/doc/Bluetooth_img/BT_circuit.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB.txt b/hhkb/doc/HHKB.txt
deleted file mode 100644
index ace931de38..0000000000
--- a/hhkb/doc/HHKB.txt
+++ /dev/null
@@ -1,199 +0,0 @@
-Alternative Controller for HHKB pro
-===================================
-I want to add vi cursor and mouse keys to HHKB. Original HHKB controller is not programmable and
-firmware source code is not open. So, customizing HHKB needs to replace original controller with programmable one.
-I used Teensy++ as alternative controller. Though a Teensy has enough ports to drive HHKB,
-Teensy++ has clean pinout and it makes programing and wiring easier.
-
-This is just a proof of concept for replacing controller of HHKB, not a complete firmware.
-
-My prototype firmware source tree is here:
-    github(http://github.com/tmk/tmk_keyboard)
-This firmware is a port of my previous project:
-    HHKB style Mod(http://geekhack.org/showwiki.php?title=Island:11930)
-PJRC:
-    Teensy++/Teensy(http://www.pjrc.com/teensy/)
-
-
-Pros:
-    * without pattern cutting, case mod  and soldering
-    * can keep original controller intact
-    * can change HHKB behaviour as you like(by C programming)
-
-Cons:
-    * void your warranty
-    * unavailability of Teensy++/Teensy(because of PS3 cracking boom?)
-
-Features:
-    * customized keymap
-    * more keymap layers
-    * mouse keys for minimum mouse operation(never comfortable for normal use)
-    * and more...(in the future)
-
-Any suggestions or ideas are welcome.
-
-
-NOTE:
-    My HHKB is just "Professional". This means followings may not be applied to "Professional2".
-
-DISCLAIMER:
-    I'm not a professional for electronics and MCU programming. This may damage your HHKB.
-    And my English writing is poor, I'm not sure I can convey my notions accurately.
-
-
-Teensy++ installation
----------------------
-Angled USB mini B adapter is used to install Teensy++ laterally.
-(teensy_install.jpg)
-
-Bread baord wires are used to connect Teensy++.
-(teensy_wiring.jpg)
-(connector_contact.jpg)
-
-
-HHKB internal
--------------
-HHKB pro has some chips on separate two PCBs.
-
-Controller PCB:
-    M38K07M4    Renesas MCU with USB function
-                http://documentation.renesas.com/eng/products/mpumcu/rej03b0192_38k0ds.pdf
-
-    (HHKB_controller.jpg)
-
-Keyswitch PCB:
-    HC4051      Analog Multiplexer: select a row line.
-                http://www.alldatasheet.com/datasheet-pdf/pdf/203989/KODENSHI/KK74HC4051A.html
-    LS145       BCD Decoder: select a column line.
-                http://www.alldatasheet.com/datasheet-pdf/pdf/27373/TI/SN74LS145D.html
-    BU9831      Non-volatile electronic potentiometer: for calibration?
-                http://www.alldatasheet.com/datasheet-pdf/pdf/36387/ROHM/BU9831.html
-    TP1683/4    Capacitive Sensing controller: no datasheet available.
-
-    (HHKB_keyswitch.jpg)
-
-    Topre original chip?
-    (HHKB_TP1684.jpg)
-
-
-Two PCBs are connected by 15 lines. Vcc and GND use 3 lines each, other 9 lines are for keyboard signaling.
-
-    Keyswitch PCB connector                                 Teensy++ pins
-    -------------------------------------------------------------------------------
-     1  Vcc(5V)                                             5V
-     2  Vcc(5V)
-     3  Vcc(5V)
-     4  TP1684    KEY: Low(0) when key pressed              PE6 input(with pullup)
-     5  TP1684    KEY_PREV: assert previous key state???    PE7 output
-     6  HC4051    A(bit0) select 8 rows(0 to 7)             PB0 output
-     7  HC4051    B(bit1)                                   PB1 output
-     8  HC4051    C(bit2)                                   PB2 output
-     9  LS145     A(bit0) select 8 columns(0 to 7)          PB3 output
-    10  LS145     B(bit1)                                   PB4 output
-    11  LS145     C(bit2)                                   PB5 output
-    12  LS145     D(enable) Low(0) enable selected column   PB6 output
-    13  GND
-    14  GND
-    15  GND                                                 GND
-
-    (HHKB_connector.jpg)
-
-
-Keyswitch matrix
-----------------
-60 keyswitches in 8*8 matrix. It is ghost-free and bounce-free.
-
-  COL 0     1       2       3       4       5       6       7
-ROW ---------------------------------------------------------------
-  0|  2     q       w       s       a       z       x       c
-  1|  3     4       r       e       d       f       v       b
-  2|  5     6       y       t       g       h       n       _NONE_
-  3|  1     Esc     Tab     Control LShift  LAlt    LMeta   Space
-  4|  7     8       u       i       k       j       m       _NONE_
-  5|  \     `       Delete  Return  Fn      RShift  RAlt    RMeta
-  6|  9     0       o       p       ;       l       ,       _NONE_
-  7|  -     +       ]       [       '       /       .       _NONE_
-
-
-Matrix diagram:
-             +-------------------------+-+-+-+-+-+-+-+     Vcc
-             |bias control?            - - - - - - - -     ---
-             |                  3.9K*8 R R R R R R R R      |
-    +--------^+      +--------+        - - - - - - - -      |  
-    |        2|      | HC4051 <0-------|-|-|-|-|-|-|-|--|R|-+
-    |         |capa. |        <1-------|-|-|-|-|-|-|-|--|R|-+
-    | TP1684  |sense |        <2-------|-|-|-|-|-|-|-|--|R|-+
-    |       11<------|        <3-------|-|-|-|-|-|-|-|--|R|-+
-    |         |      |        <4-------|-|-|-|-|-|-|-|--|R|-+
-    |         |      |        <5-------|-|-|-|-|-|-|-|--|R|-+
-    |         <-+    |        <6-------|-|-|-|-|-|-|-|--|R|-+
-    |   1   4 | |    |        <7-------|-|-|-|-|-|-|-|--|R|-+
-    +---V---^-+ |    +-^-^-^--+        0 1 2 3 4 5 6 7  33K*8
-       KEY PREV |      A B C         +-----------------+
-        |   | +-^----+ | | |         |      LS145      |
-    Vcc |   | |BU9831| | | |         +-^--^--^--^------+
-    --- |   | +------+ | | |           A  B  C  D   +------+
-     |  |   |          | | |           |  |  |  |   |      |
-    1-3 4   5          6 7 8           9 10 11 12 13-15    |
-    +--------------------------------------------------+   |
-    |                connector                         |  ---
-    +--------------------------------------------------+  GND
-                    to controller
-                                    
-
-Signals charts:
-    While pressing space bar, watched HHKB original controller signals by logic analyzer.
-    Row and column is looping between 0-7 each for selecting a key.
-    A key is scaned every about 15ms, so scan rate is 66Hz.
-
-    (HHKB_chart1.jpg)
-
-    Space bar locate at ROW:3 COL:7. A key is selected by HC4051(C,B,A) and LS145(C,B,A).
-    Key state can be read on TP1684(4/KEY) while asserting low on LS145(D). 
-
-    Usage of TP1684(5) is not clear. Controller seemed to output previous key state on this line.
-    However key state can be read without using this signal.
-
-    (HHKB_chart2.jpg)
-
-
-Matrix scan pseudo code:
-    for (row: 0-7) {
-        SELECT_ROW(row);        // set HC4051(A,B,C)
-
-        for (col: 0-7) {
-            SELECT_COL(col);    // set LS145(A,B,C)
-
-            _delay_us(40);
-
-            if (prev_key_state(row, col)) {
-                KEY_PREV_ON;
-            }
-
-            _delay_us(7);
-
-            ENALBLE_COL();      // set LS145(D) to low
-
-            _delay_us(10);
-
-            if (KEY == 0) {     // read TP1684(KEY)
-                // key pressed
-            } else {
-                // not pressed
-            }
-
-            KEY_PREV_OFF;
-            UNALBLE_COL();      // set LS145(D) to high
-
-            _delay_us(150);
-        }
-    }
-
-
-Keymap layers
--------------
-Followings are added layers with additional Fn keys.
-
-see keymap.c
-
-EOF
diff --git a/hhkb/doc/HHKB_img/HHKB_TP1684.jpg b/hhkb/doc/HHKB_img/HHKB_TP1684.jpg
deleted file mode 100644
index 0a03164094..0000000000
--- a/hhkb/doc/HHKB_img/HHKB_TP1684.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/HHKB_chart1.jpg b/hhkb/doc/HHKB_img/HHKB_chart1.jpg
deleted file mode 100644
index 1f09bd185c..0000000000
--- a/hhkb/doc/HHKB_img/HHKB_chart1.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/HHKB_chart2.jpg b/hhkb/doc/HHKB_img/HHKB_chart2.jpg
deleted file mode 100644
index 45f5ada905..0000000000
--- a/hhkb/doc/HHKB_img/HHKB_chart2.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/HHKB_connector.jpg b/hhkb/doc/HHKB_img/HHKB_connector.jpg
deleted file mode 100644
index e8a09e9b28..0000000000
--- a/hhkb/doc/HHKB_img/HHKB_connector.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/HHKB_controller.jpg b/hhkb/doc/HHKB_img/HHKB_controller.jpg
deleted file mode 100644
index e3dae8e86c..0000000000
--- a/hhkb/doc/HHKB_img/HHKB_controller.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/HHKB_keyswitch.jpg b/hhkb/doc/HHKB_img/HHKB_keyswitch.jpg
deleted file mode 100644
index 3afc269e7b..0000000000
--- a/hhkb/doc/HHKB_img/HHKB_keyswitch.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/connector_contact.jpg b/hhkb/doc/HHKB_img/connector_contact.jpg
deleted file mode 100644
index 5304bc8d7e..0000000000
--- a/hhkb/doc/HHKB_img/connector_contact.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/logic_analyzer.jpg b/hhkb/doc/HHKB_img/logic_analyzer.jpg
deleted file mode 100644
index f1b438ae77..0000000000
--- a/hhkb/doc/HHKB_img/logic_analyzer.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/probe_contact.jpg b/hhkb/doc/HHKB_img/probe_contact.jpg
deleted file mode 100644
index dc79afa0cc..0000000000
--- a/hhkb/doc/HHKB_img/probe_contact.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/teensy_install.jpg b/hhkb/doc/HHKB_img/teensy_install.jpg
deleted file mode 100644
index 873d988edb..0000000000
--- a/hhkb/doc/HHKB_img/teensy_install.jpg
+++ /dev/null
diff --git a/hhkb/doc/HHKB_img/teensy_wiring.jpg b/hhkb/doc/HHKB_img/teensy_wiring.jpg
deleted file mode 100644
index 1c4eb67434..0000000000
--- a/hhkb/doc/HHKB_img/teensy_wiring.jpg
+++ /dev/null
diff --git a/hhkb/keymap.c b/hhkb/keymap.c
deleted file mode 100644
index 85a7c31b7e..0000000000
--- a/hhkb/keymap.c
+++ /dev/null
@@ -1,221 +0,0 @@
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-/* 
- * Keymap for PFU HHKB Pro
- */
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/pgmspace.h>
-#include "host.h"
-#include "usb_keycodes.h"
-#include "print.h"
-#include "debug.h"
-#include "util.h"
-#include "keymap.h"
-
-
-// Convert physical keyboard layout to matrix array.
-// This is a macro to define keymap easily in keyboard layout form.
-#define KEYMAP( \
-    K31, K30, K00, K10, K11, K20, K21, K40, K41, K60, K61, K70, K71, K50, K51, \
-    K32, K01, K02, K13, K12, K23, K22, K42, K43, K62, K63, K73, K72, K52, \
-    K33, K04, K03, K14, K15, K24, K25, K45, K44, K65, K64, K74, K53, \
-    K34, K05, K06, K07, K16, K17, K26, K46, K66, K76, K75, K55, K54, \
-         K35, K36,           K37,                K57, K56 \
-) \
-{ \
-    { KB_##K00, KB_##K01, KB_##K02, KB_##K03, KB_##K04, KB_##K05, KB_##K06, KB_##K07 }, \
-    { KB_##K10, KB_##K11, KB_##K12, KB_##K13, KB_##K14, KB_##K15, KB_##K16, KB_##K17 }, \
-    { KB_##K20, KB_##K21, KB_##K22, KB_##K23, KB_##K24, KB_##K25, KB_##K26, KB_NO    }, \
-    { KB_##K30, KB_##K31, KB_##K32, KB_##K33, KB_##K34, KB_##K35, KB_##K36, KB_##K37 }, \
-    { KB_##K40, KB_##K41, KB_##K42, KB_##K43, KB_##K44, KB_##K45, KB_##K46, KB_NO    }, \
-    { KB_##K50, KB_##K51, KB_##K52, KB_##K53, KB_##K54, KB_##K55, KB_##K56, KB_##K57 }, \
-    { KB_##K60, KB_##K61, KB_##K62, KB_##K63, KB_##K64, KB_##K65, KB_##K66, KB_NO    }, \
-    { KB_##K70, KB_##K71, KB_##K72, KB_##K73, KB_##K74, KB_##K75, KB_##K76, KB_NO    } \
-}
-
-#define KEYCODE(layer, row, col) (pgm_read_byte(&keymaps[(layer)][(row)][(col)]))
-
-
-// Assign Fn key(0-7) to a layer to which switch with the Fn key pressed.
-static const uint8_t PROGMEM fn_layer[] = {
-    0,              // Fn0
-    1,              // Fn1
-    2,              // Fn2
-    3,              // Fn3
-    3,              // Fn4
-    4,              // Fn5
-    0,              // Fn6
-    0               // Fn7
-};
-
-// Assign Fn key(0-7) to a keycode sent when release Fn key without use of the layer.
-// See layer.c for details.
-static const uint8_t PROGMEM fn_keycode[] = {
-    KB_NO,          // Fn0
-    KB_NO,          // Fn1
-    KB_SLSH,        // Fn2
-    KB_SCLN,        // Fn3
-    KB_NO,          // Fn4
-    KB_SPC,         // Fn5
-    KB_NO,          // Fn6
-    KB_NO           // Fn7
-};
-
-static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
-    /* Layer 0: Default Layer
-     * ,-----------------------------------------------------------.
-     * |Esc|  1|  2|  3|  4|  5|  6|  7|  8|  9|  0|  -|  =|  \|  `|
-     * |-----------------------------------------------------------|
-     * |Tab  |  Q|  W|  E|  R|  T|  Y|  U|  I|  O|  P|  [|  ]|Backs|
-     * |-----------------------------------------------------------|
-     * |Contro|  A|  S|  D|  F|  G|  H|  J|  K|  L|Fn3|  '|Return  |
-     * |-----------------------------------------------------------|
-     * |Shift   |  Z|  X|  C|  V|  B|  N|  M|  ,|  .|Fn2|Shift |Fn1|
-     * `-----------------------------------------------------------'
-     *       |Gui|Alt  |Fn5                    |Alt  |Fn4|
-     *       `-------------------------------------------'
-     */
-    KEYMAP(ESC, 1,   2,   3,   4,   5,   6,   7,   8,   9,   0,   MINS,EQL, BSLS,GRV, \
-           TAB, Q,   W,   E,   R,   T,   Y,   U,   I,   O,   P,   LBRC,RBRC,BSPC, \
-           LCTL,A,   S,   D,   F,   G,   H,   J,   K,   L,   FN3, QUOT,ENT, \
-           LSFT,Z,   X,   C,   V,   B,   N,   M,   COMM,DOT, FN2, RSFT,FN1, \
-                LGUI,LALT,          FN5,                RALT,FN4),
-
-    /* Layer 1: HHKB mode (HHKB Fn)
-     * ,-----------------------------------------------------------.
-     * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
-     * |-----------------------------------------------------------|
-     * |Caps |   |   |   |   |   |   |   |Psc|Slk|Pus|Up |   |Backs|
-     * |-----------------------------------------------------------|
-     * |Contro|VoD|VoU|Mut|   |   |  *|  /|Hom|PgU|Lef|Rig|Enter   |
-     * |-----------------------------------------------------------|
-     * |Shift   |   |   |   |   |   |  +|  -|End|PgD|Dow|Shift |xxx|
-     * `-----------------------------------------------------------'
-     *      |Gui |Alt  |Space                  |Alt  |xxx|
-     *      `--------------------------------------------'
-     */ 
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-           CAPS,NO,  NO,  NO,  NO,  NO,  NO,  NO,  PSCR,SLCK,BRK, UP,  NO,  BSPC, \
-           LCTL,VOLD,VOLU,MUTE,NO,  NO,  PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \
-           LSFT,NO,  NO,  NO,  NO,  NO,  PPLS,PMNS,END, PGDN,DOWN,RSFT,FN1, \
-                LGUI,LALT,          SPC,                RALT,FN7),
-
-    /* Layer 2: Vi mode (Slash)
-     * ,-----------------------------------------------------------.
-     * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
-     * |-----------------------------------------------------------|
-     * |Tab  |Hom|PgD|Up |PgU|End|Hom|PgD|PgUlEnd|   |   |   |Backs|
-     * |-----------------------------------------------------------|
-     * |Contro|   |Lef|Dow|Rig|   |Lef|Dow|Up |Rig|   |   |Return  |
-     * |-----------------------------------------------------------|
-     * |Shift   |   |   |   |   |   |Hom|PgD|PgUlEnd|xxx|Shift |   |
-     * `-----------------------------------------------------------'
-     *       |Gui|Alt  |Space                  |Alt  |Gui|
-     *       `-------------------------------------------'
-     */
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-           TAB, HOME,PGDN,UP,  PGUP,END, HOME,PGDN,PGUP,END, NO,  NO,  NO,  BSPC, \
-           LCTL,NO,  LEFT,DOWN,RGHT,NO,  LEFT,DOWN,UP,  RGHT,NO,  NO,  ENT, \
-           LSFT,NO,  NO,  NO,  NO,  NO,  HOME,PGDN,PGUP,END, FN2, RSFT,NO, \
-                LGUI,LALT,          SPC,                RALT,RGUI),
-
-    /* Layer 3: Mouse mode (Semicolon)
-     * ,-----------------------------------------------------------.
-     * |Esc| F1| F2| F3| F4| F5| F6| F7| F8| F9|F10|F11|F12|Ins|Del|
-     * |-----------------------------------------------------------|
-     * |Tab  |MwL|MwU|McU|MwD|MwR|MwL|MwD|MwU|MwR|   |   |   |Backs|
-     * |-----------------------------------------------------------|
-     * |Contro|   |McL|McD|McR|   |McL|McD|McU|McR|xxx|   |Return  |
-     * |-----------------------------------------------------------|
-     * |Shift   |Mb4|Mb5|Mb1|Mb2|Mb3|Mb2|Mb1|Mb4|Mb5|   |Shift |   |
-     * `-----------------------------------------------------------'
-     *      |Gui |Alt  |Mb1                    |Alt  |Gui|
-     *      `--------------------------------------------'
-     * Mc: Mouse Cursor / Mb: Mouse Button / Mw: Mouse Wheel 
-     */
-#ifdef HOST_IWRAP
-// iWRAP does not support mouse wheel, use these keycodes to remap as wheel
-#define KB_KPPL KB_KP_PLUS
-#define KB_KPMI KB_KP_MINUS
-#define KB_KPAS KB_KP_ASTERISK
-#define KB_KPSL KB_KP_SLASH
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-           TAB, KPAS,KPPL,MS_U,KPMI,KPSL,KPAS,KPPL,KPMI,KPSL,NO,  NO,  NO,  BSPC, \
-           LCTL,NO,  MS_L,MS_D,MS_R,NO,  MS_L,MS_D,MS_U,MS_R,FN3, NO,  ENT, \
-           LSFT,BTN4,BTN5,BTN1,BTN2,BTN3,BTN2,BTN1,NO,  NO,  NO,  RSFT,NO, \
-                LGUI,LALT,          BTN1,               RALT,FN4),
-#else
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-           TAB, WH_L,WH_U,MS_U,WH_D,WH_R,WH_L,WH_D,WH_U,WH_R,NO,  NO,  NO,  BSPC, \
-           LCTL,NO,  MS_L,MS_D,MS_R,NO,  MS_L,MS_D,MS_U,MS_R,FN3, NO,  ENT, \
-           LSFT,BTN4,BTN5,BTN1,BTN2,BTN3,BTN2,BTN1,BTN4,BTN5,NO,  RSFT,NO, \
-                LGUI,LALT,          BTN1,               RALT,FN4),
-#endif
-
-    /* Layer 4: Matias half keyboard style (Space)
-     * ,-----------------------------------------------------------.
-     * |  -|  0|  9|  8|  7|  6|  5|  4|  3|  2|  1|   |   |   |Esc|
-     * |-----------------------------------------------------------|
-     * |Backs|  P|  O|  I|  U|  Y|  T|  R|  E|  W|  Q|   |   |Tab  |
-     * |-----------------------------------------------------------|
-     * |Contro|  ;|  L|  K|  J|  H|  G|  F|  D|  S|  A|Con|Control |
-     * |-----------------------------------------------------------|
-     * |Shift   |  /|  .|  ,|  M|  N|  B|  V|  C|  X|  Z|Shift |   |
-     * `-----------------------------------------------------------'
-     *      |Gui |Alt  |xxxxxxxxxxxxxxxxxxxxxxx|Alt  |Gui|
-     *      `--------------------------------------------'
-     */
-/*
-    KEYMAP(MINS,0,   9,   8,   7,   6,   5,   4,   3,   2,   1,   NO,  NO,  NO,  ESC, \
-           BSPC,P,   O,   I,   U,   Y,   T,   R,   E,   W,   Q,   NO,  NO,  TAB, \
-           LCTL,SCLN,L,   K,   J,   H,   G,   F,   D,   S,   A,   RCTL,RCTL, \
-           LSFT,SLSH,DOT, COMM,M,   N,   B,   V,   C,   X,   Z,   RSFT,NO, \
-                LGUI,LALT,          FN5,                RALT,RGUI)
-*/
-    /* Mouse mode (Space) */
-#ifdef HOST_IWRAP
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-           TAB, KPAS,KPPL,MS_U,KPMI,KPSL,KPAS,KPPL,KPMI,KPSL,NO,  NO,  NO,  BSPC, \
-           LCTL,NO,  MS_L,MS_D,MS_R,NO,  MS_L,MS_D,MS_U,MS_R,FN3, NO,  ENT, \
-           LSFT,BTN4,BTN5,BTN1,BTN2,BTN3,BTN2,BTN1,BTN4,BTN5,NO,  RSFT,NO, \
-                LGUI,LALT,          FN5,                RALT,RGUI),
-#else
-    KEYMAP(ESC, F1,  F2,  F3,  F4,  F5,  F6,  F7,  F8,  F9,  F10, F11, F12, INS, DEL, \
-           TAB, WH_L,WH_U,MS_U,WH_D,WH_R,WH_L,WH_D,WH_U,WH_R,NO,  NO,  NO,  BSPC, \
-           LCTL,NO,  MS_L,MS_D,MS_R,NO,  MS_L,MS_D,MS_U,MS_R,FN3, NO,  ENT, \
-           LSFT,BTN4,BTN5,BTN1,BTN2,BTN3,BTN2,BTN1,BTN4,BTN5,NO,  RSFT,NO, \
-                LGUI,LALT,          FN5,                RALT,RGUI),
-#endif
-};
-
-
-uint8_t keymap_get_keycode(uint8_t layer, uint8_t row, uint8_t col)
-{
-    return KEYCODE(layer, row, col);
-}
-
-uint8_t keymap_fn_layer(uint8_t fn_bits)
-{
-    return pgm_read_byte(&fn_layer[biton(fn_bits)]);
-}
-
-uint8_t keymap_fn_keycode(uint8_t fn_bits)
-{
-    return pgm_read_byte(&fn_keycode[(biton(fn_bits))]);
-}
diff --git a/hhkb/led.c b/hhkb/led.c
deleted file mode 100644
index 669b6107fa..0000000000
--- a/hhkb/led.c
+++ /dev/null
@@ -1,26 +0,0 @@
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-#include "stdint.h"
-#include "led.h"
-
-
-/* HHKB has no LEDs */
-void led_set(uint8_t usb_led)
-{
-}
-
diff --git a/hhkb/matrix.c b/hhkb/matrix.c
deleted file mode 100644
index 350066b904..0000000000
--- a/hhkb/matrix.c
+++ /dev/null
@@ -1,294 +0,0 @@
-/*
-Copyright 2011 Jun Wako <wakojun@gmail.com>
-
-This program is free software: you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation, either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program.  If not, see <http://www.gnu.org/licenses/>.
-*/
-
-/*
- * scan matrix
- */
-#include <stdint.h>
-#include <stdbool.h>
-#include <avr/io.h>
-#include <avr/interrupt.h>
-#include <util/delay.h>
-#include "print.h"
-#include "util.h"
-#include "timer.h"
-#include "matrix.h"
-
-
-// Timer resolution check
-#if (1000000/TIMER_RAW_FREQ > 20)
-#   error "Timer resolution(>20us) is not enough for HHKB matrix scan tweak on V-USB."
-#endif
-
-#if (MATRIX_COLS > 16)
-#   error "MATRIX_COLS must not exceed 16"
-#endif
-#if (MATRIX_ROWS > 255)
-#   error "MATRIX_ROWS must not exceed 255"
-#endif
-
-
-// matrix state buffer(1:on, 0:off)
-#if (MATRIX_COLS <= 8)
-static uint8_t *matrix;
-static uint8_t *matrix_prev;
-static uint8_t _matrix0[MATRIX_ROWS];
-static uint8_t _matrix1[MATRIX_ROWS];
-#else
-static uint16_t *matrix;
-static uint16_t *matrix_prev;
-static uint16_t _matrix0[MATRIX_ROWS];
-static uint16_t _matrix1[MATRIX_ROWS];
-#endif
-
-// HHKB has no ghost and no bounce.
-#ifdef MATRIX_HAS_GHOST
-static bool matrix_has_ghost_in_row(uint8_t row);
-#endif
-
-
-// Matrix I/O ports
-//
-// row:     HC4051[A,B,C]  selects scan row0-7
-// col:     LS145[A,B,C,D] selects scan col0-7 and enable(D)
-// key:     on: 0/off: 1
-// prev:    unknown: output previous key state(negated)?
-
-#ifdef HOST_PJRC
-// Ports for Teensy
-// row:     PB0-2
-// col:     PB3-5,6
-// key:     PE6(pull-uped)
-// prev:    PE7
-#define KEY_INIT()              do {    \
-    DDRB |= 0x7F;                       \
-    DDRE |=  (1<<7);                    \
-    DDRE &= ~(1<<6);                    \
-    PORTE |= (1<<6);                    \
-} while (0)
-#define KEY_SELECT(ROW, COL)    (PORTB = (PORTB & 0xC0) |       \
-                                         (((COL) & 0x07)<<3) |    \
-                                         ((ROW) & 0x07))
-#define KEY_ENABLE()            (PORTB &= ~(1<<6))
-#define KEY_UNABLE()            (PORTB |=  (1<<6))
-#define KEY_STATE()             (PINE & (1<<6))
-#define KEY_PREV_ON()           (PORTE |=  (1<<7))
-#define KEY_PREV_OFF()          (PORTE &= ~(1<<7))
-#define KEY_POWER_ON()
-#define KEY_POWER_OFF()
-#else
-// Ports for V-USB
-// key:     PB0(pull-uped)
-// prev:    PB1
-// row:     PB2-4
-// col:     PC0-2,3
-// power:   PB5(Low:on/Hi-z:off)
-#define KEY_INIT()              do {    \
-    DDRB  |= 0x3E;                      \
-    DDRB  &= ~(1<<0);                   \
-    PORTB |= 1<<0;                      \
-    DDRC  |= 0x0F;                      \
-    KEY_UNABLE();                       \
-    KEY_PREV_OFF();                     \
-} while (0)
-#define KEY_SELECT(ROW, COL)    do {    \
-    PORTB = (PORTB & 0xE3) | ((ROW) & 0x07)<<2; \
-    PORTC = (PORTC & 0xF8) | ((COL) & 0x07);    \
-} while (0)
-#define KEY_ENABLE()            (PORTC &= ~(1<<3))
-#define KEY_UNABLE()            (PORTC |=  (1<<3))
-#define KEY_STATE()             (PINB & (1<<0))
-#define KEY_PREV_ON()           (PORTB |=  (1<<1))
-#define KEY_PREV_OFF()          (PORTB &= ~(1<<1))
-// Power supply switching
-#define KEY_POWER_ON()          do {    \
-    KEY_INIT();                         \
-    PORTB &= ~(1<<5);                   \
-    _delay_us(200);                     \
-} while (0)
-#define KEY_POWER_OFF()         do {    \
-    DDRB  &= ~0x3F;                     \
-    PORTB &= ~0x3F;                     \
-    DDRC  &= ~0x0F;                     \
-    PORTC &= ~0x0F;                     \
-} while (0)
-#endif
-
-
-inline
-uint8_t matrix_rows(void)
-{
-    return MATRIX_ROWS;
-}
-
-inline
-uint8_t matrix_cols(void)
-{
-    return MATRIX_COLS;
-}
-
-void matrix_init(void)
-{
-    KEY_INIT();
-
-    // initialize matrix state: all keys off
-    for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix0[i] = 0x00;
-    for (uint8_t i=0; i < MATRIX_ROWS; i++) _matrix1[i] = 0x00;
-    matrix = _matrix0;
-    matrix_prev = _matrix1;
-}
-
-uint8_t matrix_scan(void)
-{
-    uint8_t *tmp;
-
-    tmp = matrix_prev;
-    matrix_prev = matrix;
-    matrix = tmp;
-
-    KEY_POWER_ON();
-    for (uint8_t row = 0; row < MATRIX_ROWS; row++) {
-        for (uint8_t col = 0; col < MATRIX_COLS; col++) {
-            KEY_SELECT(row, col);
-            _delay_us(40);
-
-            // Not sure this is needed. This just emulates HHKB controller's behaviour.
-            if (matrix_prev[row] & (1<<col)) {
-                KEY_PREV_ON();
-            }
-            _delay_us(7);
-
-            // NOTE: KEY_STATE is valid only in 20us after KEY_ENABLE.
-            // If V-USB interrupts in this section we could lose 40us or so
-            // and would read invalid value from KEY_STATE.
-            uint8_t last = TIMER_RAW;
-
-            KEY_ENABLE();
-            // Wait for KEY_STATE outputs its value.
-            // 1us was ok on one HHKB, but not worked on another.
-            _delay_us(10);
-            if (KEY_STATE()) {
-                matrix[row] &= ~(1<<col);
-            } else {
-                matrix[row] |= (1<<col);
-            }
-
-            // Ignore if this code region execution time elapses more than 20us.
-            if (TIMER_DIFF_RAW(TIMER_RAW, last) > 20/(1000000/TIMER_RAW_FREQ)) {
-                matrix[row] = matrix_prev[row];
-            }
-
-            KEY_PREV_OFF();
-            KEY_UNABLE();
-            // NOTE: KEY_STATE keep its state in 20us after KEY_ENABLE.
-            // This takes 25us or more to make sure KEY_STATE returns to idle state.
-            _delay_us(150);
-        }
-    }
-    KEY_POWER_OFF();
-    return 1;
-}
-
-bool matrix_is_modified(void)
-{
-    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
-        if (matrix[i] != matrix_prev[i])
-            return true;
-    }
-    return false;
-}
-
-inline
-bool matrix_has_ghost(void)
-{
-#ifdef MATRIX_HAS_GHOST
-    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
-        if (matrix_has_ghost_in_row(i))
-            return true;
-    }
-#endif
-    return false;
-}
-
-inline
-bool matrix_is_on(uint8_t row, uint8_t col)
-{
-    return (matrix[row] & (1<<col));
-}
-
-inline
-#if (MATRIX_COLS <= 8)
-uint8_t matrix_get_row(uint8_t row)
-#else
-uint16_t matrix_get_row(uint8_t row)
-#endif
-{
-    return matrix[row];
-}
-
-void matrix_print(void)
-{
-#if (MATRIX_COLS <= 8)
-    print("\nr/c 01234567\n");
-#else
-    print("\nr/c 0123456789ABCDEF\n");
-#endif
-    for (uint8_t row = 0; row < matrix_rows(); row++) {
-        phex(row); print(": ");
-#if (MATRIX_COLS <= 8)
-        pbin_reverse(matrix_get_row(row));
-#else
-        pbin_reverse16(matrix_get_row(row));
-#endif
-#ifdef MATRIX_HAS_GHOST
-        if (matrix_has_ghost_in_row(row)) {
-            print(" <ghost");
-        }
-#endif
-        print("\n");
-    }
-}
-
-uint8_t matrix_key_count(void)
-{
-    uint8_t count = 0;
-    for (uint8_t i = 0; i < MATRIX_ROWS; i++) {
-#if (MATRIX_COLS <= 8)
-        count += bitpop(matrix[i]);
-#else
-        count += bitpop16(matrix[i]);
-#endif
-    }
-    return count;
-}
-
-#ifdef MATRIX_HAS_GHOST
-inline
-static bool matrix_has_ghost_in_row(uint8_t row)
-{
-    // no ghost exists in case less than 2 keys on
-    if (((matrix[row] - 1) & matrix[row]) == 0)
-        return false;
-
-    // ghost exists in case same state as other row
-    for (uint8_t i=0; i < MATRIX_ROWS; i++) {
-        if (i != row && (matrix[i] & matrix[row]) == matrix[row])
-            return true;
-    }
-    return false;
-}
-#endif
diff --git a/hhkb/usbconfig.h b/hhkb/usbconfig.h
deleted file mode 100644
index c3aad34bef..0000000000
--- a/hhkb/usbconfig.h
+++ /dev/null
@@ -1,388 +0,0 @@
-/* Name: usbconfig.h
- * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
- * Author: Christian Starkjohann
- * Creation Date: 2005-04-01
- * Tabsize: 4
- * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
- * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
- * This Revision: $Id: usbconfig-prototype.h 785 2010-05-30 17:57:07Z cs $
- */
-
-#ifndef __usbconfig_h_included__
-#define __usbconfig_h_included__
-
-#include "config_vusb.h"
-
-/*
-General Description:
-This file is an example configuration (with inline documentation) for the USB
-driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
-also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
-wire the lines to any other port, as long as D+ is also wired to INT0 (or any
-other hardware interrupt, as long as it is the highest level interrupt, see
-section at the end of this file).
-*/
-
-/* ---------------------------- Hardware Config ---------------------------- */
-
-#define USB_CFG_IOPORTNAME      D
-/* This is the port where the USB bus is connected. When you configure it to
- * "B", the registers PORTB, PINB and DDRB will be used.
- */
-#define USB_CFG_DMINUS_BIT      3
-/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
- * This may be any bit in the port.
- */
-#define USB_CFG_DPLUS_BIT       2
-/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
- * This may be any bit in the port. Please note that D+ must also be connected
- * to interrupt pin INT0! [You can also use other interrupts, see section
- * "Optional MCU Description" below, or you can connect D- to the interrupt, as
- * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
- * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
- * markers every millisecond.]
- */
-#define USB_CFG_CLOCK_KHZ       (F_CPU/1000)
-/* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
- * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
- * require no crystal, they tolerate +/- 1% deviation from the nominal
- * frequency. All other rates require a precision of 2000 ppm and thus a
- * crystal!
- * Since F_CPU should be defined to your actual clock rate anyway, you should
- * not need to modify this setting.
- */
-#define USB_CFG_CHECK_CRC       0
-/* Define this to 1 if you want that the driver checks integrity of incoming
- * data packets (CRC checks). CRC checks cost quite a bit of code size and are
- * currently only available for 18 MHz crystal clock. You must choose
- * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
- */
-
-/* ----------------------- Optional Hardware Config ------------------------ */
-
-/* #define USB_CFG_PULLUP_IOPORTNAME   D */
-/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
- * V+, you can connect and disconnect the device from firmware by calling
- * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
- * This constant defines the port on which the pullup resistor is connected.
- */
-/* #define USB_CFG_PULLUP_BIT          4 */
-/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
- * above) where the 1.5k pullup resistor is connected. See description
- * above for details.
- */
-
-/* --------------------------- Functional Range ---------------------------- */
-
-#define USB_CFG_HAVE_INTRIN_ENDPOINT    1
-/* Define this to 1 if you want to compile a version with two endpoints: The
- * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
- * number).
- */
-#define USB_CFG_HAVE_INTRIN_ENDPOINT3   1
-/* Define this to 1 if you want to compile a version with three endpoints: The
- * default control endpoint 0, an interrupt-in endpoint 3 (or the number
- * configured below) and a catch-all default interrupt-in endpoint as above.
- * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
- */
-#define USB_CFG_EP3_NUMBER              3
-/* If the so-called endpoint 3 is used, it can now be configured to any other
- * endpoint number (except 0) with this macro. Default if undefined is 3.
- */
-/* #define USB_INITIAL_DATATOKEN           USBPID_DATA1 */
-/* The above macro defines the startup condition for data toggling on the
- * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
- * Since the token is toggled BEFORE sending any data, the first packet is
- * sent with the oposite value of this configuration!
- */
-#define USB_CFG_IMPLEMENT_HALT          0
-/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
- * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
- * it is required by the standard. We have made it a config option because it
- * bloats the code considerably.
- */
-#define USB_CFG_SUPPRESS_INTR_CODE      0
-/* Define this to 1 if you want to declare interrupt-in endpoints, but don't
- * want to send any data over them. If this macro is defined to 1, functions
- * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
- * you need the interrupt-in endpoints in order to comply to an interface
- * (e.g. HID), but never want to send any data. This option saves a couple
- * of bytes in flash memory and the transmit buffers in RAM.
- */
-#define USB_CFG_INTR_POLL_INTERVAL      10
-/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
- * interval. The value is in milliseconds and must not be less than 10 ms for
- * low speed devices.
- */
-#define USB_CFG_IS_SELF_POWERED         0
-/* Define this to 1 if the device has its own power supply. Set it to 0 if the
- * device is powered from the USB bus.
- */
-#define USB_CFG_MAX_BUS_POWER           100
-/* Set this variable to the maximum USB bus power consumption of your device.
- * The value is in milliamperes. [It will be divided by two since USB
- * communicates power requirements in units of 2 mA.]
- */
-#define USB_CFG_IMPLEMENT_FN_WRITE      1
-/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
- * transfers. Set it to 0 if you don't need it and want to save a couple of
- * bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_READ       0
-/* Set this to 1 if you need to send control replies which are generated
- * "on the fly" when usbFunctionRead() is called. If you only want to send
- * data from a static buffer, set it to 0 and return the data from
- * usbFunctionSetup(). This saves a couple of bytes.
- */
-#define USB_CFG_IMPLEMENT_FN_WRITEOUT   0
-/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
- * You must implement the function usbFunctionWriteOut() which receives all
- * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
- * can be found in 'usbRxToken'.
- */
-#define USB_CFG_HAVE_FLOWCONTROL        0
-/* Define this to 1 if you want flowcontrol over USB data. See the definition
- * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
- * usbdrv.h.
- */
-#define USB_CFG_DRIVER_FLASH_PAGE       0
-/* If the device has more than 64 kBytes of flash, define this to the 64 k page
- * where the driver's constants (descriptors) are located. Or in other words:
- * Define this to 1 for boot loaders on the ATMega128.
- */
-#define USB_CFG_LONG_TRANSFERS          0
-/* Define this to 1 if you want to send/receive blocks of more than 254 bytes
- * in a single control-in or control-out transfer. Note that the capability
- * for long transfers increases the driver size.
- */
-/* #define USB_RX_USER_HOOK(data, len)     if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
-/* This macro is a hook if you want to do unconventional things. If it is
- * defined, it's inserted at the beginning of received message processing.
- * If you eat the received message and don't want default processing to
- * proceed, do a return after doing your things. One possible application
- * (besides debugging) is to flash a status LED on each packet.
- */
-/* #define USB_RESET_HOOK(resetStarts)     if(!resetStarts){hadUsbReset();} */
-/* This macro is a hook if you need to know when an USB RESET occurs. It has
- * one parameter which distinguishes between the start of RESET state and its
- * end.
- */
-/* #define USB_SET_ADDRESS_HOOK()              hadAddressAssigned(); */
-/* This macro (if defined) is executed when a USB SET_ADDRESS request was
- * received.
- */
-#define USB_COUNT_SOF                   1
-/* define this macro to 1 if you need the global variable "usbSofCount" which
- * counts SOF packets. This feature requires that the hardware interrupt is
- * connected to D- instead of D+.
- */
-/* #ifdef __ASSEMBLER__
- * macro myAssemblerMacro
- *     in      YL, TCNT0
- *     sts     timer0Snapshot, YL
- *     endm
- * #endif
- * #define USB_SOF_HOOK                    myAssemblerMacro
- * This macro (if defined) is executed in the assembler module when a
- * Start Of Frame condition is detected. It is recommended to define it to
- * the name of an assembler macro which is defined here as well so that more
- * than one assembler instruction can be used. The macro may use the register
- * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
- * immediately after an SOF pulse may be lost and must be retried by the host.
- * What can you do with this hook? Since the SOF signal occurs exactly every
- * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
- * designs running on the internal RC oscillator.
- * Please note that Start Of Frame detection works only if D- is wired to the
- * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
- */
-#define USB_CFG_CHECK_DATA_TOGGLING     0
-/* define this macro to 1 if you want to filter out duplicate data packets
- * sent by the host. Duplicates occur only as a consequence of communication
- * errors, when the host does not receive an ACK. Please note that you need to
- * implement the filtering yourself in usbFunctionWriteOut() and
- * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
- * for each control- and out-endpoint to check for duplicate packets.
- */
-#define USB_CFG_HAVE_MEASURE_FRAME_LENGTH   0
-/* define this macro to 1 if you want the function usbMeasureFrameLength()
- * compiled in. This function can be used to calibrate the AVR's RC oscillator.
- */
-#define USB_USE_FAST_CRC                0
-/* The assembler module has two implementations for the CRC algorithm. One is
- * faster, the other is smaller. This CRC routine is only used for transmitted
- * messages where timing is not critical. The faster routine needs 31 cycles
- * per byte while the smaller one needs 61 to 69 cycles. The faster routine
- * may be worth the 32 bytes bigger code size if you transmit lots of data and
- * run the AVR close to its limit.
- */
-
-/* -------------------------- Device Description --------------------------- */
-
-#define USB_CFG_VENDOR_ID       (VENDOR_ID & 0xFF), ((VENDOR_ID >> 8) & 0xFF)
-/* USB vendor ID for the device, low byte first. If you have registered your
- * own Vendor ID, define it here. Otherwise you may use one of obdev's free
- * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_ID       (PRODUCT_ID & 0xFF), ((PRODUCT_ID >> 8) & 0xFF)
-/* This is the ID of the product, low byte first. It is interpreted in the
- * scope of the vendor ID. If you have registered your own VID with usb.org
- * or if you have licensed a PID from somebody else, define it here. Otherwise
- * you may use one of obdev's free shared VID/PID pairs. See the file
- * USB-IDs-for-free.txt for details!
- * *** IMPORTANT NOTE ***
- * This template uses obdev's shared VID/PID pair for Vendor Class devices
- * with libusb: 0x16c0/0x5dc.  Use this VID/PID pair ONLY if you understand
- * the implications!
- */
-#define USB_CFG_DEVICE_VERSION  0x00, 0x01
-/* Version number of the device: Minor number first, then major number.
- */
-#define USB_CFG_VENDOR_NAME     't', '.', 'm', '.', 'k', '.'
-#define USB_CFG_VENDOR_NAME_LEN 6
-/* These two values define the vendor name returned by the USB device. The name
- * must be given as a list of characters under single quotes. The characters
- * are interpreted as Unicode (UTF-16) entities.
- * If you don't want a vendor name string, undefine these macros.
- * ALWAYS define a vendor name containing your Internet domain name if you use
- * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
- * details.
- */
-#define USB_CFG_DEVICE_NAME     'H', 'H', 'K', 'B', ' ', 'm', 'o', 'd'
-#define USB_CFG_DEVICE_NAME_LEN 8
-/* Same as above for the device name. If you don't want a device name, undefine
- * the macros. See the file USB-IDs-for-free.txt before you assign a name if
- * you use a shared VID/PID.
- */
-/*#define USB_CFG_SERIAL_NUMBER   'N', 'o', 'n', 'e' */
-/*#define USB_CFG_SERIAL_NUMBER_LEN   0 */
-/* Same as above for the serial number. If you don't want a serial number,
- * undefine the macros.
- * It may be useful to provide the serial number through other means than at
- * compile time. See the section about descriptor properties below for how
- * to fine tune control over USB descriptors such as the string descriptor
- * for the serial number.
- */
-#define USB_CFG_DEVICE_CLASS        0
-#define USB_CFG_DEVICE_SUBCLASS     0
-/* See USB specification if you want to conform to an existing device class.
- * Class 0xff is "vendor specific".
- */
-#define USB_CFG_INTERFACE_CLASS     3   /* HID */
-#define USB_CFG_INTERFACE_SUBCLASS  1   /* Boot */
-#define USB_CFG_INTERFACE_PROTOCOL  1   /* Keyboard */
-/* See USB specification if you want to conform to an existing device class or
- * protocol. The following classes must be set at interface level:
- * HID class is 3, no subclass and protocol required (but may be useful!)
- * CDC class is 2, use subclass 2 and protocol 1 for ACM
- */
-#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH    0
-/* Define this to the length of the HID report descriptor, if you implement
- * an HID device. Otherwise don't define it or define it to 0.
- * If you use this define, you must add a PROGMEM character array named
- * "usbHidReportDescriptor" to your code which contains the report descriptor.
- * Don't forget to keep the array and this define in sync!
- */
-
-/* #define USB_PUBLIC static */
-/* Use the define above if you #include usbdrv.c instead of linking against it.
- * This technique saves a couple of bytes in flash memory.
- */
-
-/* ------------------- Fine Control over USB Descriptors ------------------- */
-/* If you don't want to use the driver's default USB descriptors, you can
- * provide our own. These can be provided as (1) fixed length static data in
- * flash memory, (2) fixed length static data in RAM or (3) dynamically at
- * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
- * information about this function.
- * Descriptor handling is configured through the descriptor's properties. If
- * no properties are defined or if they are 0, the default descriptor is used.
- * Possible properties are:
- *   + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
- *     at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
- *     used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
- *     you want RAM pointers.
- *   + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
- *     in static memory is in RAM, not in flash memory.
- *   + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
- *     the driver must know the descriptor's length. The descriptor itself is
- *     found at the address of a well known identifier (see below).
- * List of static descriptor names (must be declared PROGMEM if in flash):
- *   char usbDescriptorDevice[];
- *   char usbDescriptorConfiguration[];
- *   char usbDescriptorHidReport[];
- *   char usbDescriptorString0[];
- *   int usbDescriptorStringVendor[];
- *   int usbDescriptorStringDevice[];
- *   int usbDescriptorStringSerialNumber[];
- * Other descriptors can't be provided statically, they must be provided
- * dynamically at runtime.
- *
- * Descriptor properties are or-ed or added together, e.g.:
- * #define USB_CFG_DESCR_PROPS_DEVICE   (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
- *
- * The following descriptors are defined:
- *   USB_CFG_DESCR_PROPS_DEVICE
- *   USB_CFG_DESCR_PROPS_CONFIGURATION
- *   USB_CFG_DESCR_PROPS_STRINGS
- *   USB_CFG_DESCR_PROPS_STRING_0
- *   USB_CFG_DESCR_PROPS_STRING_VENDOR
- *   USB_CFG_DESCR_PROPS_STRING_PRODUCT
- *   USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
- *   USB_CFG_DESCR_PROPS_HID
- *   USB_CFG_DESCR_PROPS_HID_REPORT
- *   USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
- *
- * Note about string descriptors: String descriptors are not just strings, they
- * are Unicode strings prefixed with a 2 byte header. Example:
- * int  serialNumberDescriptor[] = {
- *     USB_STRING_DESCRIPTOR_HEADER(6),
- *     'S', 'e', 'r', 'i', 'a', 'l'
- * };
- */
-
-#define USB_CFG_DESCR_PROPS_DEVICE                  0
-#define USB_CFG_DESCR_PROPS_CONFIGURATION           USB_PROP_IS_DYNAMIC
-//#define USB_CFG_DESCR_PROPS_CONFIGURATION           0
-#define USB_CFG_DESCR_PROPS_STRINGS                 0
-#define USB_CFG_DESCR_PROPS_STRING_0                0
-#define USB_CFG_DESCR_PROPS_STRING_VENDOR           0
-#define USB_CFG_DESCR_PROPS_STRING_PRODUCT          0
-#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER    0
-#define USB_CFG_DESCR_PROPS_HID                     USB_PROP_IS_DYNAMIC
-//#define USB_CFG_DESCR_PROPS_HID                     0
-#define USB_CFG_DESCR_PROPS_HID_REPORT              USB_PROP_IS_DYNAMIC
-//#define USB_CFG_DESCR_PROPS_HID_REPORT              0
-#define USB_CFG_DESCR_PROPS_UNKNOWN                 0
-
-/* ----------------------- Optional MCU Description ------------------------ */
-
-/* The following configurations have working defaults in usbdrv.h. You
- * usually don't need to set them explicitly. Only if you want to run
- * the driver on a device which is not yet supported or with a compiler
- * which is not fully supported (such as IAR C) or if you use a differnt
- * interrupt than INT0, you may have to define some of these.
- */
-/* #define USB_INTR_CFG            MCUCR */
-/* #define USB_INTR_CFG_SET        ((1 << ISC00) | (1 << ISC01)) */
-/* #define USB_INTR_CFG_CLR        0 */
-/* #define USB_INTR_ENABLE         GIMSK */
-/* #define USB_INTR_ENABLE_BIT     INT0 */
-/* #define USB_INTR_PENDING        GIFR */
-/* #define USB_INTR_PENDING_BIT    INTF0 */
-/* #define USB_INTR_VECTOR         INT0_vect */
-
-/* Set INT1 for D- falling edge to count SOF */
-/* #define USB_INTR_CFG            EICRA */
-#define USB_INTR_CFG_SET        ((1 << ISC11) | (0 << ISC10))
-/* #define USB_INTR_CFG_CLR        0 */
-/* #define USB_INTR_ENABLE         EIMSK */
-#define USB_INTR_ENABLE_BIT     INT1
-/* #define USB_INTR_PENDING        EIFR */
-#define USB_INTR_PENDING_BIT    INTF1
-#define USB_INTR_VECTOR         INT1_vect
-
-#endif /* __usbconfig_h_included__ */