/* Copyright 2022 Thomas Baart <thomas@splitkb.com> This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ #pragma once /* USB Device descriptor parameter */ #define VENDOR_ID 0x8D1D #define PRODUCT_ID 0x9D9D #define DEVICE_VER 0x0002 #define MANUFACTURER splitkb #define PRODUCT Kyria rev2 /* key matrix size */ /* Rows are doubled up */ #define MATRIX_ROWS 8 #define MATRIX_COLS 8 // wiring #define MATRIX_ROW_PINS \ { F6, F7, B1, B3 } #define MATRIX_COL_PINS \ { B2, B6, B5, B4, E6, D7, C6, D4 } #define MATRIX_ROW_PINS_RIGHT \ { D4, C6, D7, E6 } #define MATRIX_COL_PINS_RIGHT \ { B4, B5, B6, B2, B3, B1, F7, F6 } #define ENCODERS_PAD_A \ { F4 } #define ENCODERS_PAD_B \ { F5 } #define ENCODERS_PAD_A_RIGHT \ { F5 } #define ENCODERS_PAD_B_RIGHT \ { F4 } /* COL2ROW, ROW2COL*/ #define DIODE_DIRECTION COL2ROW // Side detection // col 4 row 3 on right-hand-side #define SPLIT_HAND_MATRIX_GRID E6, B3 // row first because the board is col2row #define SPLIT_HAND_MATRIX_GRID_LOW_IS_RIGHT #define MATRIX_MASKED // actual mask is defined by `matrix_mask` in `rev2.c` /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ #define DEBOUNCE 5 /* * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. */ #if defined(CONVERT_TO_PROTON_C) # define SERIAL_USART_FULL_DUPLEX // Enable full duplex operation mode. # define SERIAL_USART_PIN_SWAP // Swap TX and RX pins if keyboard is master halve. # define SERIAL_USART_DRIVER SD1 // USART driver of TX pin. default: SD1 # define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7 # define SERIAL_USART_TX_PIN D3 # define SERIAL_USART_RX_PIN D2 # define RGB_DI_PIN PAL_LINE(GPIOA, 3) # define WS2812_PWM_DRIVER PWMD2 // default: PWMD2 # define WS2812_PWM_CHANNEL 4 // default: 2 # define WS2812_PWM_PAL_MODE 1 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 2 # define WS2812_DMA_STREAM STM32_DMA1_STREAM2 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. # define WS2812_DMA_CHANNEL 2 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU. # define WS2812_DMAMUX_ID STM32_DMAMUX1_TIM2_UP // DMAMUX configuration for TIMx_UP -- only required if your MCU has a DMAMUX peripheral, see the respective reference manual for the appropriate values for your MCU. #else # define RGB_DI_PIN D3 # define SOFT_SERIAL_PIN D2 #endif #define RGBLED_SPLIT \ { 10, 10 } #define RGBLED_NUM 20 #ifdef OLED_ENABLE # define OLED_DISPLAY_128X64 # define SPLIT_OLED_ENABLE #endif /* RGB matrix support */ #ifdef RGB_MATRIX_ENABLE # define SPLIT_TRANSPORT_MIRROR # define DRIVER_LED_TOTAL RGBLED_NUM // Number of LEDs # define RGB_MATRIX_SPLIT { 10, 10 } # define RGB_MATRIX_MAXIMUM_BRIGHTNESS 170 # define RGB_DISABLE_WHEN_USB_SUSPENDED #endif