/* Copyright 2021 jurassic73 This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 2 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ #pragma once #include "config_common.h" /* * Keyboard Matrix Assignments * * Change this to how you wired your keyboard * COLS: AVR pins used for columns, left to right * ROWS: AVR pins used for rows, top to bottom * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) * */ /* key matrix size ROWS = total count of rows for both sides - this is broken out accordingly in split.h COLS = number of cols per side which curently needs to be equal so there are blank columns for the left side in the split89.h file */ #define MATRIX_ROWS 12 #define MATRIX_COLS 10 /* Left side matrix */ #define MATRIX_ROW_PINS { F6, F7, B1, B3, B2, B6 } #define MATRIX_COL_PINS { F5, F4, B5, B4, E6, D7, C6, D4, D2, D3 } /* Right side matrix */ #define MATRIX_ROW_PINS_RIGHT { F6, F7, B1, B3, B2, B6 } #define MATRIX_COL_PINS_RIGHT { F5, F4, B5, B4, E6, D7, C6, D4, D2, D3 } /* this will be tied to high (VCC with a 2k to 10k resistor) on the left keyboard half and tied to low (GND using a wire jumper only) on the right keyboard half. This allows a user to plug in a USB cable to either side and function correctly with or without a TRS/TRRS cable with a single hex file. */ #define SPLIT_HAND_PIN D1 /* COL2ROW, ROW2COL */ #define DIODE_DIRECTION COL2ROW /* handedness */ /* * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN. */ #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6 //#define LED_NUM_LOCK_PIN B0 //#define LED_CAPS_LOCK_PIN B1 //#define LED_SCROLL_LOCK_PIN B2 //#define LED_COMPOSE_PIN B3 //#define LED_KANA_PIN B4 //#define BACKLIGHT_PIN B7 //#define BACKLIGHT_LEVELS 3 //#define BACKLIGHT_BREATHING //#define RGB_DI_PIN E2 //#ifdef RGB_DI_PIN //# define RGBLED_NUM 16 //# define RGBLIGHT_HUE_STEP 8 //# define RGBLIGHT_SAT_STEP 8 //# define RGBLIGHT_VAL_STEP 8 //# define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */ //# define RGBLIGHT_SLEEP /* If defined, the RGB lighting will be switched off when the host goes to sleep */ /*== customize breathing effect ==*/ /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/ //# define RGBLIGHT_BREATHE_TABLE_SIZE 256 // 256(default) or 128 or 64 /*==== use exp() and sin() ====*/ //# define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85 // 1 to 2.7 //# define RGBLIGHT_EFFECT_BREATHE_MAX 255 // 0 to 255 //#endif /* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ #define DEBOUNCE 5 /* define if matrix has ghost (lacks anti-ghosting diodes) */ //#define MATRIX_HAS_GHOST /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ #define LOCKING_SUPPORT_ENABLE /* Locking resynchronize hack */ #define LOCKING_RESYNC_ENABLE /* If defined, GRAVE_ESC will always act as ESC when CTRL is held. * This is useful for the Windows task manager shortcut (ctrl+shift+esc). */ //#define GRAVE_ESC_CTRL_OVERRIDE /* * Force NKRO * * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the * makefile for this to work.) * * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) * until the next keyboard reset. * * NKRO may prevent your keystrokes from being detected in the BIOS, but it is * fully operational during normal computer usage. * * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by * bootmagic, NKRO mode will always be enabled until it is toggled again during a * power-up. * */ //#define FORCE_NKRO /* * Feature disable options * These options are also useful to firmware size reduction. */ /* disable debug print */ //#define NO_DEBUG /* disable print */ //#define NO_PRINT /* disable action features */ //#define NO_ACTION_LAYER //#define NO_ACTION_TAPPING //#define NO_ACTION_ONESHOT /* Bootmagic Lite key configuration */ //#define BOOTMAGIC_LITE_ROW 0 //#define BOOTMAGIC_LITE_COLUMN 0