/**
 * Copyright 2021 Charly Delay <charly@codesink.dev> (@0xcharly)
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
#pragma once

#undef PRODUCT
#define PRODUCT "Charybdis (4x6) Blackpill"

#undef MATRIX_COL_PINS
#define MATRIX_COL_PINS \
    { B0, B1, B12, B3, B4, B5 }
#undef MATRIX_COL_PINS_RIGHT
#define MATRIX_COL_PINS_RIGHT \
    { B0, B1, B12, B3, B4, B5 }

#undef MATRIX_ROW_PINS
#define MATRIX_ROW_PINS \
    { B15, A2, B8, A8, B9 }
#undef MATRIX_ROW_PINS_RIGHT
#define MATRIX_ROW_PINS_RIGHT \
    { B15, A2, B8, A8, B9 }


#define DIODE_DIRECTION ROW2COL
#define SPLIT_HAND_PIN A3
#undef MASTER_RIGHT
#define USB_VBUS_PIN B10

#undef RGB_DI_PIN
#define RGB_DI_PIN A1
#define WS2812_EXTERNAL_PULLUP
#define WS2812_PWM_DRIVER PWMD2
#define WS2812_PWM_CHANNEL 2
#define WS2812_PWM_PAL_MODE 1
#define WS2812_EXTERNAL_PULLUP
#define WS2812_DMA_STREAM STM32_DMA1_STREAM1
#define WS2812_DMA_CHANNEL 3
#define WS2812_PWM_TARGET_PERIOD 800000

#define DEBUG_LED_PIN     C13

#define AUDIO_PIN          B7
#define AUDIO_PWM_DRIVER   PWMD4
#define AUDIO_PWM_CHANNEL  2
#define AUDIO_PWM_PAL_MODE 2
#define AUDIO_INIT_DELAY
#define AUDIO_ENABLE_TONE_MULTIPLEXING
#define AUDIO_TONE_MULTIPLEXING_RATE_DEFAULT 10

#undef SOFT_SERIAL_PIN
// #define SERIAL_USART_FULL_DUPLEX  // Enable full duplex operation mode.
#define SERIAL_USART_TX_PIN      A9
// #define SERIAL_USART_RX_PIN      A3
// #define SERIAL_USART_DRIVER      SD2
// #define SERIAL_USART_TX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
// #define SERIAL_USART_RX_PAL_MODE 7    // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
// #define SERIAL_USART_TIMEOUT     100  // USART driver timeout. default 100
// #define SERIAL_USART_SPEED       921600
#define SERIAL_USART_SPEED (1.5 * 1024 * 1024)

#define CRC8_USE_TABLE
#define CRC8_OPTIMIZE_SPEED

/* spi config for eeprom and pmw3360 sensor */
#define SPI_DRIVER                           SPID1
#define SPI_SCK_PIN                          A5
#define SPI_SCK_PAL_MODE                     5
#define SPI_MOSI_PIN                         A7
#define SPI_MOSI_PAL_MODE                    5
#define SPI_MISO_PIN                         A6
#define SPI_MISO_PAL_MODE                    5

#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A4
#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR    64

#undef PMW33XX_CS_PIN
#define PMW33XX_CS_PIN                       A15  // b14
#define PMW33XX_LIFTOFF_DISTANCE 0b1111
#undef ROTATIONAL_TRANSFORM_ANGLE
#define ROTATIONAL_TRANSFORM_ANGLE -65

#define CHARYBDIS_MINIMUM_DEFAULT_DPI     1200
#define CHARYBDIS_DEFAULT_DPI_CONFIG_STEP 400
#define CHARYBDIS_MINIMUM_SNIPING_DPI     200
#define CHARYBDIS_SNIPING_DPI_CONFIG_STEP 100

/* RGB Matrix. */

#undef RGB_MATRIX_MAXIMUM_BRIGHTNESS
#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 150

#define CHARYBDIS_CONFIG_SYNC

#define BOOTMAGIC_LITE_ROW    0
#define BOOTMAGIC_LITE_COLUMN 0
#define BOOTMAGIC_LITE_ROW_RIGHT    5
#define BOOTMAGIC_LITE_COLUMN_RIGHT 0
#define BOOTMAGIC_LITE_EEPROM_ROW    1
#define BOOTMAGIC_LITE_EEPROM_COLUMN 0
#define BOOTMAGIC_LITE_EEPROM_ROW_RIGHT    1
#define BOOTMAGIC_LITE_EEPROM_COLUMN_RIGHT 0