From 44441de8cad7255fd0637459ed39b89e34751b78 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sun, 7 Aug 2016 17:04:39 +0300 Subject: Split keyboard makefiles into rules and Makefile --- keyboards/s60-x/Makefile | 76 ++---------------------------------------------- keyboards/s60-x/rules.mk | 69 +++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 71 insertions(+), 74 deletions(-) create mode 100644 keyboards/s60-x/rules.mk (limited to 'keyboards/s60-x') diff --git a/keyboards/s60-x/Makefile b/keyboards/s60-x/Makefile index 8b51d4609f..4e2a6f00fd 100644 --- a/keyboards/s60-x/Makefile +++ b/keyboards/s60-x/Makefile @@ -1,75 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile -endif - - +endif \ No newline at end of file diff --git a/keyboards/s60-x/rules.mk b/keyboards/s60-x/rules.mk new file mode 100644 index 0000000000..7ec93933a9 --- /dev/null +++ b/keyboards/s60-x/rules.mk @@ -0,0 +1,69 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 \ No newline at end of file -- cgit v1.2.3 From da226e61261e0c11e678d2086c00b2a45726083e Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Sat, 20 Aug 2016 03:22:16 +0300 Subject: Update keyboard readme files with new makefile instructions --- keyboards/s60-x/readme.md | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'keyboards/s60-x') diff --git a/keyboards/s60-x/readme.md b/keyboards/s60-x/readme.md index 099d586991..94ce829223 100644 --- a/keyboards/s60-x/readme.md +++ b/keyboards/s60-x/readme.md @@ -42,9 +42,9 @@ The recommended programs for flashing your keyboard are [Atmel FLIP](http://www. ## Building the firmware -To build firmware binary hex file with a certain keymap just run `make` with the `keymap` option like: +To build the firmware binary hex file with a keymap just do `make` with a keymap like this: - $ make keymap=[custom|poker|poker_set|poker_bit|plain|hasu|spacefn|hhkb|] + $ make [custom|poker|poker_set|poker_bit|plain|hasu|spacefn|hhkb|] For a more detailed explanation of the build process and the environment setup, see the ["Getting Started" section](/readme.md#getting-started). -- cgit v1.2.3