From 5d34e70cf773531536dda363fc43c60146e3d97c Mon Sep 17 00:00:00 2001 From: fauxpark Date: Sat, 26 Oct 2019 12:32:18 +1100 Subject: Cleanup rules.mk for 32U4 keyboards, N-Q (#7147) --- keyboards/noxary/220/rules.mk | 51 ++--------------------------------------- keyboards/noxary/260/rules.mk | 5 ++-- keyboards/noxary/268/rules.mk | 50 ++++++++-------------------------------- keyboards/noxary/268_2/rules.mk | 43 +++------------------------------- keyboards/noxary/280/rules.mk | 51 ++--------------------------------------- keyboards/noxary/x268/rules.mk | 51 ++--------------------------------------- 6 files changed, 22 insertions(+), 229 deletions(-) (limited to 'keyboards/noxary') diff --git a/keyboards/noxary/220/rules.mk b/keyboards/noxary/220/rules.mk index af8b7d6839..785fb488d4 100644 --- a/keyboards/noxary/220/rules.mk +++ b/keyboards/noxary/220/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/noxary/260/rules.mk b/keyboards/noxary/260/rules.mk index 646d38de36..4d9977cd3b 100644 --- a/keyboards/noxary/260/rules.mk +++ b/keyboards/noxary/260/rules.mk @@ -7,7 +7,8 @@ MCU = atmega32u4 # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu # Build Options @@ -32,4 +33,4 @@ FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) EXTRAFLAGS += -flto -LAYOUTS = 60_ansi 60_iso 60_hhkb 60_tsangan_hhkb \ No newline at end of file +LAYOUTS = 60_ansi 60_iso 60_hhkb 60_tsangan_hhkb diff --git a/keyboards/noxary/268/rules.mk b/keyboards/noxary/268/rules.mk index d0b4ce2b59..59e6b524cf 100644 --- a/keyboards/noxary/268/rules.mk +++ b/keyboards/noxary/268/rules.mk @@ -1,45 +1,15 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - +# Bootloader selection +# Teensy halfkay +# Pro Micro caterina +# Atmel DFU atmel-dfu +# LUFA DFU lufa-dfu +# QMK DFU qmk-dfu +# ATmega32A bootloadHID +# ATmega328P USBasp +BOOTLOADER = atmel-dfu # Build Options # comment out to disable the options. @@ -53,4 +23,4 @@ SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend NKRO_ENABLE ?= yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work BACKLIGHT_ENABLE ?= yes # Enable keyboard backlight functionality AUDIO_ENABLE ?= no -RGBLIGHT_ENABLE ?= no \ No newline at end of file +RGBLIGHT_ENABLE ?= no diff --git a/keyboards/noxary/268_2/rules.mk b/keyboards/noxary/268_2/rules.mk index d1d781ccfa..2f9d087656 100644 --- a/keyboards/noxary/268_2/rules.mk +++ b/keyboards/noxary/268_2/rules.mk @@ -1,53 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - # Build Options # change yes to no to disable # @@ -69,4 +32,4 @@ AUDIO_ENABLE = no # Audio output on port C6 FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) -LAYOUTS = 65_ansi_blocker \ No newline at end of file +LAYOUTS = 65_ansi_blocker diff --git a/keyboards/noxary/280/rules.mk b/keyboards/noxary/280/rules.mk index f99ee37b0d..7ac7c8f654 100644 --- a/keyboards/noxary/280/rules.mk +++ b/keyboards/noxary/280/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # diff --git a/keyboards/noxary/x268/rules.mk b/keyboards/noxary/x268/rules.mk index 3c4a26ad1a..8b2d28fcda 100644 --- a/keyboards/noxary/x268/rules.mk +++ b/keyboards/noxary/x268/rules.mk @@ -1,63 +1,16 @@ # MCU name MCU = atmega32u4 -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - # Bootloader selection # Teensy halfkay # Pro Micro caterina # Atmel DFU atmel-dfu # LUFA DFU lufa-dfu # QMK DFU qmk-dfu -# atmega32a bootloadHID +# ATmega32A bootloadHID +# ATmega328P USBasp BOOTLOADER = atmel-dfu - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - # Build Options # change yes to no to disable # -- cgit v1.2.3