From a26ee57eb8202e7da31049b1761ca74be5184414 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ren=C3=A9=20Werner?= Date: Mon, 22 Aug 2016 20:34:29 +0200 Subject: Added support for the Kitten Paw controller This adds support for the 2016 revision of the Kitten Paw [1] replacement controller by Bathroom Epiphanies. [1] http://bathroomepiphanies.com/controllers/ --- keyboards/kitten_paw/Makefile | 77 ++++++++++++ keyboards/kitten_paw/config.h | 162 +++++++++++++++++++++++++ keyboards/kitten_paw/keymaps/default/keymap.c | 51 ++++++++ keyboards/kitten_paw/kitten_paw.c | 30 +++++ keyboards/kitten_paw/kitten_paw.h | 47 ++++++++ keyboards/kitten_paw/led.c | 47 ++++++++ keyboards/kitten_paw/matrix.c | 164 ++++++++++++++++++++++++++ keyboards/kitten_paw/readme.md | 32 +++++ 8 files changed, 610 insertions(+) create mode 100644 keyboards/kitten_paw/Makefile create mode 100644 keyboards/kitten_paw/config.h create mode 100644 keyboards/kitten_paw/keymaps/default/keymap.c create mode 100644 keyboards/kitten_paw/kitten_paw.c create mode 100644 keyboards/kitten_paw/kitten_paw.h create mode 100644 keyboards/kitten_paw/led.c create mode 100644 keyboards/kitten_paw/matrix.c create mode 100644 keyboards/kitten_paw/readme.md (limited to 'keyboards/kitten_paw') diff --git a/keyboards/kitten_paw/Makefile b/keyboards/kitten_paw/Makefile new file mode 100644 index 0000000000..9122921737 --- /dev/null +++ b/keyboards/kitten_paw/Makefile @@ -0,0 +1,77 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u2 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 + OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +CUSTOM_MATRIX = yes +SRC += matrix.c led.c + +ifndef QUANTUM_DIR + include ../../Makefile +endif + diff --git a/keyboards/kitten_paw/config.h b/keyboards/kitten_paw/config.h new file mode 100644 index 0000000000..d7089734aa --- /dev/null +++ b/keyboards/kitten_paw/config.h @@ -0,0 +1,162 @@ +/* +Copyright 2012 Jun Wako + +This program is free software: you can redistribute it and/or modify +it under the terms of the GNU General Public License as published by +the Free Software Foundation, either version 2 of the License, or +(at your option) any later version. + +This program is distributed in the hope that it will be useful, +but WITHOUT ANY WARRANTY; without even the implied warranty of +MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +GNU General Public License for more details. + +You should have received a copy of the GNU General Public License +along with this program. If not, see . +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6050 +#define DEVICE_VER 0x0104 +#define MANUFACTURER Costar +#define PRODUCT Majestouch + +/* key matrix size */ +#define MATRIX_ROWS 8 +#define MATRIX_COLS 18 + +/* + * Keyboard Matrix Assignments + * + * Change this to how you wired your keyboard + * COLS: AVR pins used for columns, left to right + * ROWS: AVR pins used for rows, top to bottom + * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) + * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) + * +*/ +//#define MATRIX_ROW_PINS { D0, D5 } +//#define MATRIX_COL_PINS { F1, F0, B0 } +//#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +// #define BACKLIGHT_PIN B7 +// #define BACKLIGHT_BREATHING +// #define BACKLIGHT_LEVELS 3 + + +/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ +#define DEBOUNCING_DELAY 5 + +/* define if matrix has ghost (lacks anti-ghosting diodes) */ +//#define MATRIX_HAS_GHOST + +/* number of backlight levels */ + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* + * Force NKRO + * + * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved + * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the + * makefile for this to work.) + * + * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) + * until the next keyboard reset. + * + * NKRO may prevent your keystrokes from being detected in the BIOS, but it is + * fully operational during normal computer usage. + * + * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) + * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by + * bootmagic, NKRO mode will always be enabled until it is toggled again during a + * power-up. + * + */ +//#define FORCE_NKRO + +/* + * Magic Key Options + * + * Magic keys are hotkey commands that allow control over firmware functions of + * the keyboard. They are best used in combination with the HID Listen program, + * found here: https://www.pjrc.com/teensy/hid_listen.html + * + * The options below allow the magic key functionality to be changed. This is + * useful if your keyboard/keypad is missing keys and you want magic key support. + * + */ + +/* key combination for magic key command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* control how magic key switches layers */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false + +/* override magic key keymap */ +//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS +//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM +//#define MAGIC_KEY_HELP1 H +//#define MAGIC_KEY_HELP2 SLASH +//#define MAGIC_KEY_DEBUG D +//#define MAGIC_KEY_DEBUG_MATRIX X +//#define MAGIC_KEY_DEBUG_KBD K +//#define MAGIC_KEY_DEBUG_MOUSE M +//#define MAGIC_KEY_VERSION V +//#define MAGIC_KEY_STATUS S +//#define MAGIC_KEY_CONSOLE C +//#define MAGIC_KEY_LAYER0_ALT1 ESC +//#define MAGIC_KEY_LAYER0_ALT2 GRAVE +//#define MAGIC_KEY_LAYER0 0 +//#define MAGIC_KEY_LAYER1 1 +//#define MAGIC_KEY_LAYER2 2 +//#define MAGIC_KEY_LAYER3 3 +//#define MAGIC_KEY_LAYER4 4 +//#define MAGIC_KEY_LAYER5 5 +//#define MAGIC_KEY_LAYER6 6 +//#define MAGIC_KEY_LAYER7 7 +//#define MAGIC_KEY_LAYER8 8 +//#define MAGIC_KEY_LAYER9 9 +//#define MAGIC_KEY_BOOTLOADER PAUSE +//#define MAGIC_KEY_LOCK CAPS +//#define MAGIC_KEY_EEPROM E +//#define MAGIC_KEY_NKRO N +//#define MAGIC_KEY_SLEEP_LED Z + +/* + * Feature disable options + * These options are also useful to firmware size reduction. + */ + +/* disable debug print */ +//#define NO_DEBUG + +/* disable print */ +//#define NO_PRINT + +/* disable action features */ +//#define NO_ACTION_LAYER +//#define NO_ACTION_TAPPING +//#define NO_ACTION_ONESHOT +//#define NO_ACTION_MACRO +//#define NO_ACTION_FUNCTION + +#endif diff --git a/keyboards/kitten_paw/keymaps/default/keymap.c b/keyboards/kitten_paw/keymaps/default/keymap.c new file mode 100644 index 0000000000..f672357455 --- /dev/null +++ b/keyboards/kitten_paw/keymaps/default/keymap.c @@ -0,0 +1,51 @@ +#include "kitten_paw.h" + +enum layers { + DEFAULT, +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [DEFAULT] = KEYMAP(\ + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0,KC_MINS, KC_EQL,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P,KC_LBRC,KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L,KC_SCLN,KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ + KC_LSFT,KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT,KC_SLSH, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ + KC_LCTL,KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI,KC_MENU,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT) +}; + +const uint16_t PROGMEM fn_actions[] = { + +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { + register_code(KC_RSFT); + } else { + unregister_code(KC_RSFT); + } + break; + } + return MACRO_NONE; +}; + + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + return true; +} + +void led_set_user(uint8_t usb_led) { + +} \ No newline at end of file diff --git a/keyboards/kitten_paw/kitten_paw.c b/keyboards/kitten_paw/kitten_paw.c new file mode 100644 index 0000000000..8713baf433 --- /dev/null +++ b/keyboards/kitten_paw/kitten_paw.c @@ -0,0 +1,30 @@ +#include "kitten_paw.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + + matrix_init_quantum(); + matrix_init_user(); +} + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + + matrix_scan_quantum(); + matrix_scan_user(); +} + +bool process_record_kb(uint16_t keycode, keyrecord_t *record) { + // put your per-action keyboard code here + // runs for every action, just before processing by the firmware + + return process_record_user(keycode, record); +} + +void led_set_kb(uint8_t usb_led) { + // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here + + led_set_user(usb_led); +} diff --git a/keyboards/kitten_paw/kitten_paw.h b/keyboards/kitten_paw/kitten_paw.h new file mode 100644 index 0000000000..a6c1d27de7 --- /dev/null +++ b/keyboards/kitten_paw/kitten_paw.h @@ -0,0 +1,47 @@ +#ifndef KITTEN_PAW_H +#define KITTEN_PAW_H + +#include "quantum.h" + +// This a shortcut to help you visually see your layout. +// The first section contains all of the arguements +// The second converts the arguments into a two-dimensional array +/* + Matrix col/row mapping + + ,----. ,-------------------. ,-------------------. ,-------------------. ,--------------. + | J6 | | I4 | H4 | H2 | H6 | | A7 | E6 | D2 | D4 | | B4 | B7 | B6 | B0 | | C7 | C5 | A5 | + `----' `-------------------' `-------------------' `-------------------' `--------------' + ,-------------------------------------------------------------------------. ,--------------. ,-------------------. + | J4 | J7 | I7 | H7 | G7 | G4 | F4 | F7 | E7 | D7 | R7 | R4 | E4 | B2 | | L4 | O4 | Q4 | | K1 | L1 | Q1 | Q0 | + |-------------------------------------------------------------------------| |--------------| |-------------------| + | J2 | J5 | I5 | H5 | G5 | G2 | F2 | F5 | E5 | D5 | R5 | R2 | E2 | B3 | | K4 | O7 | Q7 | | K5 | L5 | Q5 | O5 | + |-------------------------------------------------------------------------| '--------------' |-------------- | + | O5 | J3 | I3 | H3 | G3 | G6 | F6 | F3 | E3 | D3 | R3 | R6 | B1 | | K2 | L2 | Q2 | | + |-------------------------------------------------------------------------| ,----. |-------------------| + | N2 | J1 | I1 | H1 | G1 | G0 | F0 | F1 | E1 | D1 | R0 | N3 | | O6 | | K3 | L3 | Q3 | O3 | + |-------------------------------------------------------------------------| ,--------------. |-------------- | + | A4 | P2 | C6 | K6 | C0 | M3 | D0 | A1 | | O0 | K0 | L0 | | L6 | Q6 | | + `-------------------------------------------------------------------------' `--------------' `-------------------' +*/ + +#define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{ \ + {KC_NO, KB0, KC0, KD0,KC_NO, KF0, KG0,KC_NO,KC_NO,KC_NO, KK0, KL0,KC_NO,KC_NO, KO0,KC_NO, KQ0, KR0}, \ + { KA1, KB1,KC_NO, KD1, KE1, KF1, KG1, KH1, KI1, KJ1, KK1, KL1,KC_NO,KC_NO,KC_NO,KC_NO, KQ1,KC_NO}, \ + {KC_NO, KB2,KC_NO, KD2, KE2, KF2, KG2, KH2, KI2, KJ2, KK2, KL2,KC_NO, KN2,KC_NO, KP2, KQ2, KR2}, \ + {KC_NO, KB3,KC_NO, KD3, KE3, KF3, KG3, KH3, KI3, KJ3, KK3, KL3, KM3, KN3, KO3,KC_NO, KQ3, KR3}, \ + { KA4, KB4,KC_NO, KD4, KE4, KF4, KG4, KH4, KI4, KJ4, KK4, KL4,KC_NO,KC_NO, KO4,KC_NO, KQ4, KR4}, \ + { KA5,KC_NO, KC5, KD5, KE5, KF5, KG5, KH5, KI5, KJ5, KK5, KL5,KC_NO,KC_NO, KO5,KC_NO, KQ5, KR5}, \ + {KC_NO, KB6, KC6,KC_NO, KE6, KF6, KG6, KH6, KI6, KJ6, KK6, KL6,KC_NO,KC_NO, KO6,KC_NO, KQ6, KR6}, \ + { KA7, KB7, KC7, KD7, KE7, KF7, KG7, KH7, KI7, KJ7,KC_NO,KC_NO,KC_NO,KC_NO, KO7,KC_NO, KQ7, KR7} \ +} + +#endif diff --git a/keyboards/kitten_paw/led.c b/keyboards/kitten_paw/led.c new file mode 100644 index 0000000000..a1bf057c4c --- /dev/null +++ b/keyboards/kitten_paw/led.c @@ -0,0 +1,47 @@ +/* + Copyright 2014 Ralf Schmitt + + This program is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program. If not, see . +*/ + +#include +#include "stdint.h" +#include "led.h" + +/* LED pin configuration + * + * Scroll Lock PC5 + * Caps Lock PC6 + * Num Lock PB7 + * + */ +void led_set(uint8_t usb_led) { + DDRB |= (1<<7); + DDRC |= (1<<5) | (1<<6); + + if (usb_led & (1< + + This program is free software: you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation, either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program. If not, see . +*/ + +#include +#include +#include +#include +#include "print.h" +#include "debug.h" +#include "util.h" +#include "matrix.h" + +#ifndef DEBOUNCING_DELAY +# define DEBOUNCING_DELAY 5 +#endif +static uint8_t debouncing = DEBOUNCING_DELAY; + +static matrix_row_t matrix[MATRIX_ROWS]; +static matrix_row_t matrix_debouncing[MATRIX_ROWS]; + +static uint8_t read_rows(void); +static void select_col(uint8_t col); + +inline uint8_t matrix_rows(void) { + return MATRIX_ROWS; +} + +inline uint8_t matrix_cols(void) { + return MATRIX_COLS; +} + +/* Column pin configuration + * + * col: 0 1 2 3 4 5 6 7 + * pin: PC7 PD5 PD3 PD1 PC2 PD6 PD4 PD2 + * + * Rrr pin configuration + * + * These rrrs uses one 74HC154 4 to 16 bit demultiplexer (low + * active), together with 2 rrrs driven directly from the micro + * controller, to control the 18 rrrs. The rrrs are driven from + * pins B6,5,4,3,2,1,0. + */ +void matrix_init(void) { + DDRC &= ~0b10000100; // Row input pins + DDRD &= ~0b01111110; + PORTC |= 0b10000100; + PORTD |= 0b01111110; + + DDRB |= 0b01111111; // Column output pins + + for (uint8_t i=0; i < MATRIX_ROWS; i++) { + matrix[i] = 0; + matrix_debouncing[i] = 0; + } +} + +uint8_t matrix_scan(void) { + for (uint8_t col = 0; col < MATRIX_COLS; col++) { + select_col(col); + _delay_us(3); + uint8_t rows = read_rows(); + for (uint8_t row = 0; row < MATRIX_ROWS; row++) { + bool prev_bit = matrix_debouncing[row] & ((matrix_row_t)1<] +``` + +Keymaps follow the format **__keymap.c__** and are stored in folders in the `keymaps` folder, eg `keymaps/my_keymap/` -- cgit v1.2.3 From feebc58d327b969fe1ef11cd5b5989a60c51ac87 Mon Sep 17 00:00:00 2001 From: Fred Sundvik Date: Tue, 23 Aug 2016 09:42:11 +0300 Subject: Split kitten_paw into Makefile/rules.mk --- keyboards/kitten_paw/Makefile | 76 +------------------------------------------ keyboards/kitten_paw/rules.mk | 72 ++++++++++++++++++++++++++++++++++++++++ 2 files changed, 73 insertions(+), 75 deletions(-) create mode 100644 keyboards/kitten_paw/rules.mk (limited to 'keyboards/kitten_paw') diff --git a/keyboards/kitten_paw/Makefile b/keyboards/kitten_paw/Makefile index 9122921737..57b2ef62e5 100644 --- a/keyboards/kitten_paw/Makefile +++ b/keyboards/kitten_paw/Makefile @@ -1,77 +1,3 @@ - - -# MCU name -#MCU = at90usb1287 -MCU = atmega32u2 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 - OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) -EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) -CONSOLE_ENABLE ?= yes # Console for debug(+400) -COMMAND_ENABLE ?= yes # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE ?= no # USB Nkey Rollover -BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default -MIDI_ENABLE ?= no # MIDI controls -UNICODE_ENABLE ?= no # Unicode -BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE ?= no # Audio output on port C6 - -CUSTOM_MATRIX = yes -SRC += matrix.c led.c - -ifndef QUANTUM_DIR +ifndef MAKEFILE_INCLUDED include ../../Makefile endif - diff --git a/keyboards/kitten_paw/rules.mk b/keyboards/kitten_paw/rules.mk new file mode 100644 index 0000000000..dab7cabc52 --- /dev/null +++ b/keyboards/kitten_paw/rules.mk @@ -0,0 +1,72 @@ + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u2 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 + OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# change yes to no to disable +# +BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700) +EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450) +CONSOLE_ENABLE ?= yes # Console for debug(+400) +COMMAND_ENABLE ?= yes # Commands for debug and configuration +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend +# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +NKRO_ENABLE ?= no # USB Nkey Rollover +BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality on B7 by default +MIDI_ENABLE ?= no # MIDI controls +UNICODE_ENABLE ?= no # Unicode +BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID +AUDIO_ENABLE ?= no # Audio output on port C6 + +CUSTOM_MATRIX = yes +SRC += matrix.c led.c -- cgit v1.2.3 From 06c82a063bd668cb0b5b80d455c6fd7384131c86 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ren=C3=A9=20Werner?= Date: Tue, 23 Aug 2016 12:15:29 +0200 Subject: Fixed wrong keycode in default keymap Where I used KC_MENU I should have used KC_APP instead. --- keyboards/kitten_paw/keymaps/default/keymap.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'keyboards/kitten_paw') diff --git a/keyboards/kitten_paw/keymaps/default/keymap.c b/keyboards/kitten_paw/keymaps/default/keymap.c index f672357455..64aa672d0a 100644 --- a/keyboards/kitten_paw/keymaps/default/keymap.c +++ b/keyboards/kitten_paw/keymaps/default/keymap.c @@ -11,7 +11,7 @@ const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P,KC_LBRC,KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L,KC_SCLN,KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ KC_LSFT,KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT,KC_SLSH, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ - KC_LCTL,KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI,KC_MENU,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT) + KC_LCTL,KC_LGUI,KC_LALT, KC_SPC, KC_RALT,KC_RGUI, KC_APP,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT) }; const uint16_t PROGMEM fn_actions[] = { -- cgit v1.2.3 From 6a61c89477678e3df9aba9189b3dd67fc24e94ab Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ren=C3=A9=20Werner?= Date: Tue, 23 Aug 2016 13:20:59 +0200 Subject: added my personal keymap I ported my keymap from tmk to QMK. --- keyboards/kitten_paw/keymaps/ickerwx/config.h | 31 ++++ keyboards/kitten_paw/keymaps/ickerwx/keymap.c | 220 ++++++++++++++++++++++++++ 2 files changed, 251 insertions(+) create mode 100644 keyboards/kitten_paw/keymaps/ickerwx/config.h create mode 100644 keyboards/kitten_paw/keymaps/ickerwx/keymap.c (limited to 'keyboards/kitten_paw') diff --git a/keyboards/kitten_paw/keymaps/ickerwx/config.h b/keyboards/kitten_paw/keymaps/ickerwx/config.h new file mode 100644 index 0000000000..04a2d253c7 --- /dev/null +++ b/keyboards/kitten_paw/keymaps/ickerwx/config.h @@ -0,0 +1,31 @@ +#ifndef CONFIG_USER_H +#define CONFIG_USER_H + +#include "../../config.h" + +#undef MOUSEKEY_MOVE_MAX +#define MOUSEKEY_MOVE_MAX 127 +#undef MOUSEKEY_WHEEL_MAX +#define MOUSEKEY_WHEEL_MAX 110 +#undef MOUSEKEY_MOVE_DELTA +#define MOUSEKEY_MOVE_DELTA 5 +#undef MOUSEKEY_WHEEL_DELTA +#define MOUSEKEY_WHEEL_DELTA 1 +#undef MOUSEKEY_DELAY +#define MOUSEKEY_DELAY 50 +#undef MOUSEKEY_INTERVAL +#define MOUSEKEY_INTERVAL 20 +#undef MOUSEKEY_MAX_SPEED +#define MOUSEKEY_MAX_SPEED 4 +#undef MOUSEKEY_TIME_TO_MAX +#define MOUSEKEY_TIME_TO_MAX 30 +#undef MOUSEKEY_WHEEL_MAX_SPEED +#define MOUSEKEY_WHEEL_MAX_SPEED 3 +#undef MOUSEKEY_WHEEL_TIME_TO_MAX +#define MOUSEKEY_WHEEL_TIME_TO_MAX 1000 +#undef ONESHOT_TIMEOUT +#define ONESHOT_TIMEOUT 500 +#undef TAPPING_TOGGLE +#define TAPPING_TOGGLE 2 + +#endif diff --git a/keyboards/kitten_paw/keymaps/ickerwx/keymap.c b/keyboards/kitten_paw/keymaps/ickerwx/keymap.c new file mode 100644 index 0000000000..276fc30a80 --- /dev/null +++ b/keyboards/kitten_paw/keymaps/ickerwx/keymap.c @@ -0,0 +1,220 @@ +#include "kitten_paw.h" +#include "mousekey.h" + +#define _______ KC_TRNS +#define XXXXXXX KC_NO +#define LC LCTL +#define KC_SLCT KC_SELECT + +enum layers { + DEFAULT, + PROG1, + PROG2, + MEDIA, + MOUSE1, + MOUSE2, + MISC, +}; + +enum function_id { + LSHFT_PAREN, + RSHFT_PAREN, + LCTRL_BRACKET, + RCTRL_BRACKET, + LALT_CURLY, + RALT_CURLY, + CTRL_CLICK +}; + +enum macro_id { + GRV, + CFLEX +}; + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { + [DEFAULT] = KEYMAP(\ + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ + F(0), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ + F(8),KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT, KC_SLSH, F(9), KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ + F(1),KC_LGUI, F(3), LT(MISC, KC_SPC), F(4), F(5), LT(MEDIA, KC_APP), F(2), KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT), + /* Layer 1: Programming Layer 1, emulating US layout */ + [PROG1] = KEYMAP(\ + KC_ESC,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, _______, _______, _______,_______,_______, \ + M(GRV),_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, KC_SLSH, S(KC_0), _______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,_______,_______,_______,_______, KC_Z,_______,_______,_______, _______,RALT(KC_8),RALT(KC_9),RALT(KC_MINS), _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,S(KC_COMM),S(KC_BSLS), _______, _______,_______,_______, \ + MO(PROG2),_______, KC_Y,_______,_______,_______,_______,_______,_______,_______, _______, S(KC_7), MO(PROG2), _______, _______,_______,_______,_______, \ + _______,_______,_______, _______, _______, _______, _______, _______, _______,_______,_______, _______,_______), + /* Layer 2: programming layer 2 + all keys that are not FN keys are sent as LSFT+key on this layer + */ + [PROG2] = KEYMAP(\ + _______, _______, _______,_______,_______,_______, _______,_______, _______,_______, _______, _______, _______, _______,_______,_______, \ +RALT(KC_RBRC), _______,RALT(KC_Q),KC_BSLS,_______,_______,M(CFLEX),S(KC_6),S(KC_RBRC),S(KC_8), S(KC_9), S(KC_SLSH), KC_RBRC, _______, _______,_______,_______, _______,_______,_______,_______, \ + _______, _______, _______,_______,_______,_______, _______,_______, _______,_______, _______, RALT(KC_7),RALT(KC_0),RALT(KC_NUBS), _______,_______,_______, _______,_______,_______,_______, \ + _______, _______, _______,_______,_______,_______, _______,_______, _______,_______, S(KC_DOT), S(KC_2), _______, _______,_______,_______, \ + _______,S(KC_NUBS), _______,_______,_______,_______, _______,_______, _______,KC_NUBS,S(KC_NUBS), S(KC_MINS), _______, _______, _______,_______,_______,_______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______,_______,_______, _______,_______), \ + /* Layer 3: media layer */ + [MEDIA] = KEYMAP(\ + KC_PWR,KC_SLEP,KC_WAKE,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_MPRV,KC_MPLY,KC_MNXT, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_VOLD,KC_MUTE,KC_VOLU, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, KC_EJCT, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,_______,XXXXXXX, KC_MRWD,KC_MSTP,KC_MFFD, XXXXXXX,XXXXXXX), + /* Layer 4: Mouse layer */ + [MOUSE1] = KEYMAP(\ + F(6),XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,KC_ACL0, KC_ACL1, KC_ACL2, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,KC_BTN4, KC_WH_D, KC_MS_U, KC_WH_U, XXXXXXX, KC_Y,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_DEL, KC_END,KC_PGDN, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + F(0),KC_BTN5, KC_MS_L, KC_MS_D, KC_MS_R, F(7),KC_WH_L,KC_WH_D,KC_WH_U, KC_WH_R, XXXXXXX,XXXXXXX, KC_BTN1, XXXXXXX,XXXXXXX,XXXXXXX, \ + MO(MOUSE2),XXXXXXX,LC(KC_Y),LC(KC_X),LC(KC_C),LC(KC_V),XXXXXXX,KC_BTN2,KC_BTN3,LC(KC_PGUP),LC(KC_PGDN),XXXXXXX, KC_RSFT, KC_UP, XXXXXXX,XXXXXXX,XXXXXXX,KC_PENT, \ + KC_LCTL,KC_LGUI,KC_LALT, KC_BTN1, KC_RALT,KC_RGUI, KC_APP,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, XXXXXXX,XXXXXXX), + /* Layer 5: Mouse layer 2*/ + [MOUSE2] = KEYMAP(\ + _______,_______,_______, _______, _______, _______,_______,_______,_______, _______, _______,_______,_______, _______,_______,_______, \ + _______,_______,_______, _______, _______, _______,_______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,KC_BTN2, KC_WH_U, KC_BTN3, _______,_______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,KC_WH_L, KC_WH_D, KC_WH_R, _______,KC_MS_L,KC_MS_D,KC_MS_U, KC_MS_R, _______,_______, _______, _______,_______,_______, \ + _______,_______,_______, _______, _______, _______,_______,_______,_______, _______, _______,_______, _______, _______, _______,_______,_______,_______, \ + _______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______), + /* Layer 6: Misc layer */ + [MISC] = KEYMAP(\ + XXXXXXX, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24, XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,KC_SLCT,LC(KC_W), KC_UP, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,KC_BSPC, KC_DEL, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT, XXXXXXX,KC_HOME,KC_PGDN,KC_PGUP, XXXXXXX, XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ + KC_LSFT,XXXXXXX,LC(KC_Y),LC(KC_X),LC(KC_C),LC(KC_V), KC_SPC, KC_END,XXXXXXX,LC(KC_PGUP),LC(KC_PGDN),XXXXXXX, KC_RSFT, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + KC_LCTL,KC_LGUI, KC_LALT, LT(MISC, KC_SPC), KC_RALT,KC_RGUI, KC_APP,KC_RCTL, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX), +}; + +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_TAP_TOGGLE(MOUSE1), // toggle enable mouse layer (4) + [1] = ACTION_FUNCTION_TAP(LCTRL_BRACKET), // tap to print [ + [2] = ACTION_FUNCTION_TAP(RCTRL_BRACKET), // tap to print ] + [3] = ACTION_FUNCTION_TAP(LALT_CURLY), // tap to print { + [4] = ACTION_FUNCTION_TAP(RALT_CURLY), // tap to print } + [5] = ACTION_LAYER_TAP_TOGGLE(PROG1), // toggle programming layer 1 (1) + [6] = ACTION_LAYER_SET_CLEAR(DEFAULT), + [7] = ACTION_FUNCTION_TAP(CTRL_CLICK), + [8] = ACTION_FUNCTION_TAP(LSHFT_PAREN), // tap to print ( + [9] = ACTION_FUNCTION_TAP(RSHFT_PAREN), // tap to print ) +}; + +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) +{ + // MACRODOWN only works in this function + switch(id) { + case GRV: // macro to print accent grave + return (record->event.pressed ? + MACRO( D(LSFT), T(EQL), U(RALT), T(SPC), END) : + MACRO_NONE ); + case CFLEX: // print accent circonflex + return (record->event.pressed ? + MACRO( T(GRV), T(SPC), END ) : + MACRO_NONE ); + } + return MACRO_NONE; +}; + + +void matrix_init_user(void) { + +} + +void matrix_scan_user(void) { + +} + +void led_set_user(uint8_t usb_led) { + +} + +void tap_helper(keyrecord_t *record, uint16_t orig_mod, uint16_t macro_mod, uint16_t macro_kc ) { + if (record->event.pressed) { + if (record->tap.count > 0 && !record->tap.interrupted) { + if (record->tap.interrupted) { + register_mods(MOD_BIT(orig_mod)); + } + } else { + register_mods(MOD_BIT(orig_mod)); + } + } else { + if (record->tap.count > 0 && !(record->tap.interrupted)) { + add_weak_mods(MOD_BIT(macro_mod)); + send_keyboard_report(); + register_code(macro_kc); + unregister_code(macro_kc); + del_weak_mods(MOD_BIT(macro_mod)); + send_keyboard_report(); + record->tap.count = 0; // ad hoc: cancel tap + } else { + unregister_mods(MOD_BIT(orig_mod)); + } + } +} + +/* if LCTRL is tabbed, print (, or ) if RCTRL is tabbed, same for LALT/RALT and [/] */ +void action_function(keyrecord_t *record, uint8_t id, uint8_t opt) { + // The code is copied from keymap_hasu.c in the tmk keyboards hhkb folder + switch (id) { + case LCTRL_BRACKET: + tap_helper(record, KC_LCTL, KC_RALT, KC_8); + break; + case RCTRL_BRACKET: + tap_helper(record, KC_RCTL, KC_RALT, KC_9); + break; + case LALT_CURLY: + tap_helper(record, KC_LALT, KC_RALT, KC_7); + break; + case RALT_CURLY: + tap_helper(record, KC_RALT, KC_RALT, KC_0); + break; + case LSHFT_PAREN: + tap_helper(record, KC_LSFT, KC_LSFT, KC_8); + break; + case RSHFT_PAREN: + tap_helper(record, KC_RSFT, KC_LSFT, KC_9); + break; + case CTRL_CLICK: + if (record->event.pressed) { + mousekey_clear(); + register_mods(MOD_BIT(KC_LCTL)); + send_keyboard_report(); + wait_ms(5); + mousekey_on(KC_BTN1); + mousekey_send(); + wait_ms(10); + mousekey_off(KC_BTN1); + mousekey_send(); + wait_ms(5); + unregister_mods(MOD_BIT(KC_LCTL)); + send_keyboard_report(); + } + break; + } +} + +bool process_record_user(uint16_t keycode, keyrecord_t *record) { + uint8_t layer; + layer = biton32(layer_state); + if (layer == PROG2) { + if (keycode >= KC_A && keycode <= KC_EXSEL && \ + !( // do not send LSFT + these keycodes, they are needed for emulating the US layout + keycode == KC_NONUS_BSLASH || + keycode == KC_RBRC || + keycode == KC_BSLS || + keycode == KC_GRV + )) { + if (record->event.pressed) { + register_mods(MOD_LSFT); + } else { + unregister_mods(MOD_LSFT); + } + } + } + return true; +} -- cgit v1.2.3 From 1bbd3c1eea78abf0b36a289fb37f80dfc4f9c8bb Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Ren=C3=A9=20Werner?= Date: Thu, 25 Aug 2016 12:25:57 +0200 Subject: fixed defaulf keymap, added my own keymap now the LEDs are working like they should --- keyboards/kitten_paw/Makefile | 2 +- keyboards/kitten_paw/keymaps/ickerwx/keymap.c | 128 +++++++++++++++---------- keyboards/kitten_paw/keymaps/ickerwx/readme.md | 18 ++++ keyboards/kitten_paw/kitten_paw.c | 19 +++- keyboards/kitten_paw/kitten_paw.h | 11 +++ keyboards/kitten_paw/led.c | 47 --------- keyboards/kitten_paw/matrix.c | 3 +- 7 files changed, 123 insertions(+), 105 deletions(-) create mode 100644 keyboards/kitten_paw/keymaps/ickerwx/readme.md delete mode 100644 keyboards/kitten_paw/led.c (limited to 'keyboards/kitten_paw') diff --git a/keyboards/kitten_paw/Makefile b/keyboards/kitten_paw/Makefile index 9122921737..3b5585ed6f 100644 --- a/keyboards/kitten_paw/Makefile +++ b/keyboards/kitten_paw/Makefile @@ -69,7 +69,7 @@ BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID AUDIO_ENABLE ?= no # Audio output on port C6 CUSTOM_MATRIX = yes -SRC += matrix.c led.c +SRC += matrix.c ifndef QUANTUM_DIR include ../../Makefile diff --git a/keyboards/kitten_paw/keymaps/ickerwx/keymap.c b/keyboards/kitten_paw/keymaps/ickerwx/keymap.c index 276fc30a80..9a00c80dc8 100644 --- a/keyboards/kitten_paw/keymaps/ickerwx/keymap.c +++ b/keyboards/kitten_paw/keymaps/ickerwx/keymap.c @@ -3,8 +3,14 @@ #define _______ KC_TRNS #define XXXXXXX KC_NO -#define LC LCTL +#define C(kc) LCTL(KC_##kc) +#define RA(kc) RALT(KC_##kc) #define KC_SLCT KC_SELECT +#define MEDAPP LT(MEDIA, KC_APP) +#undef S +#define S(kc) LSFT(KC_##kc) + +uint8_t current_layer_global = 255; enum layers { DEFAULT, @@ -33,75 +39,75 @@ enum macro_id { const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { [DEFAULT] = KEYMAP(\ - KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \ - KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ - KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ - F(0), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ - F(8),KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT, KC_SLSH, F(9), KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ - F(1),KC_LGUI, F(3), LT(MISC, KC_SPC), F(4), F(5), LT(MEDIA, KC_APP), F(2), KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT), - /* Layer 1: Programming Layer 1, emulating US layout */ + KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR,KC_SLCK,KC_PAUS, \ + KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0,KC_MINS, KC_EQL,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, KC_NLCK,KC_PSLS,KC_PAST,KC_PMNS, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P,KC_LBRC,KC_RBRC,KC_BSLS, KC_DEL, KC_END,KC_PGDN, KC_P7, KC_P8, KC_P9,KC_PPLS, \ + F(0), KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L,KC_SCLN,KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, \ + F(8),KC_NUBS, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M,KC_COMM, KC_DOT,KC_SLSH, F(9), KC_UP, KC_P1, KC_P2, KC_P3,KC_PENT, \ + F(1),KC_LGUI, F(3), LT(MISC, KC_SPC), F(4), F(5), MEDAPP, F(2), KC_LEFT,KC_DOWN,KC_RGHT, KC_P0,KC_PDOT), + /* Layer 1: Programming Layer 1, emulating US l ayout */ [PROG1] = KEYMAP(\ - KC_ESC,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, _______, _______, _______,_______,_______, \ - M(GRV),_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, KC_SLSH, S(KC_0), _______, _______,_______,_______, _______,_______,_______,_______, \ - _______,_______,_______,_______,_______,_______, KC_Z,_______,_______,_______, _______,RALT(KC_8),RALT(KC_9),RALT(KC_MINS), _______,_______,_______, _______,_______,_______,_______, \ - _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,S(KC_COMM),S(KC_BSLS), _______, _______,_______,_______, \ - MO(PROG2),_______, KC_Y,_______,_______,_______,_______,_______,_______,_______, _______, S(KC_7), MO(PROG2), _______, _______,_______,_______,_______, \ - _______,_______,_______, _______, _______, _______, _______, _______, _______,_______,_______, _______,_______), + KC_ESC,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, \ + M(GRV),_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,KC_SLSH, S(0),_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,_______,_______,_______,_______, KC_Z,_______,_______,_______,_______, RA(8), RA(9),RA(MINS), _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,S(COMM),S(BSLS), _______, _______,_______,_______, \ + MO(PROG2),_______, KC_Y,_______,_______,_______,_______,_______,_______,_______,_______, S(7), MO(PROG2), _______, _______,_______,_______,_______, \ + _______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______), /* Layer 2: programming layer 2 all keys that are not FN keys are sent as LSFT+key on this layer */ [PROG2] = KEYMAP(\ - _______, _______, _______,_______,_______,_______, _______,_______, _______,_______, _______, _______, _______, _______,_______,_______, \ -RALT(KC_RBRC), _______,RALT(KC_Q),KC_BSLS,_______,_______,M(CFLEX),S(KC_6),S(KC_RBRC),S(KC_8), S(KC_9), S(KC_SLSH), KC_RBRC, _______, _______,_______,_______, _______,_______,_______,_______, \ - _______, _______, _______,_______,_______,_______, _______,_______, _______,_______, _______, RALT(KC_7),RALT(KC_0),RALT(KC_NUBS), _______,_______,_______, _______,_______,_______,_______, \ - _______, _______, _______,_______,_______,_______, _______,_______, _______,_______, S(KC_DOT), S(KC_2), _______, _______,_______,_______, \ - _______,S(KC_NUBS), _______,_______,_______,_______, _______,_______, _______,KC_NUBS,S(KC_NUBS), S(KC_MINS), _______, _______, _______,_______,_______,_______, \ - _______, _______, _______, _______, _______, _______, _______, _______, _______,_______,_______, _______,_______), \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, \ + RA(RBRC),_______, RA(Q),KC_BSLS,_______,_______,M(CFLEX), S(6),S(RBRC), S(8), S(9),S(SLSH),KC_RBRC,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, RA(7), RA(0),RA(NUBS), _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______, S(DOT), S(2), _______, _______,_______,_______, \ + _______,S(NUBS),_______,_______,_______,_______,_______,_______,_______,KC_NUBS,S(NUBS),S(MINS), _______, _______, _______,_______,_______,_______, \ + _______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______), /* Layer 3: media layer */ - [MEDIA] = KEYMAP(\ - KC_PWR,KC_SLEP,KC_WAKE,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_MPRV,KC_MPLY,KC_MNXT, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_VOLD,KC_MUTE,KC_VOLU, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, KC_EJCT, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,_______,XXXXXXX, KC_MRWD,KC_MSTP,KC_MFFD, XXXXXXX,XXXXXXX), + [MEDIA] = KEYMAP(\ + KC_PWR,KC_SLEP,KC_WAKE,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_MPRV,KC_MPLY,KC_MNXT, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_VOLD,KC_MUTE,KC_VOLU, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, KC_EJCT, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ + XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,_______,XXXXXXX, KC_MRWD,KC_MSTP,KC_MFFD, XXXXXXX,XXXXXXX), /* Layer 4: Mouse layer */ [MOUSE1] = KEYMAP(\ - F(6),XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,KC_ACL0, KC_ACL1, KC_ACL2, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,KC_BSPC, KC_INS,KC_HOME,KC_PGUP, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,KC_BTN4, KC_WH_D, KC_MS_U, KC_WH_U, XXXXXXX, KC_Y,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, KC_DEL, KC_END,KC_PGDN, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - F(0),KC_BTN5, KC_MS_L, KC_MS_D, KC_MS_R, F(7),KC_WH_L,KC_WH_D,KC_WH_U, KC_WH_R, XXXXXXX,XXXXXXX, KC_BTN1, XXXXXXX,XXXXXXX,XXXXXXX, \ - MO(MOUSE2),XXXXXXX,LC(KC_Y),LC(KC_X),LC(KC_C),LC(KC_V),XXXXXXX,KC_BTN2,KC_BTN3,LC(KC_PGUP),LC(KC_PGDN),XXXXXXX, KC_RSFT, KC_UP, XXXXXXX,XXXXXXX,XXXXXXX,KC_PENT, \ - KC_LCTL,KC_LGUI,KC_LALT, KC_BTN1, KC_RALT,KC_RGUI, KC_APP,KC_RCTL, KC_LEFT,KC_DOWN,KC_RGHT, XXXXXXX,XXXXXXX), + F(6),_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, \ + _______,KC_ACL0,KC_ACL1,KC_ACL2,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,KC_BTN4,KC_WH_D,KC_MS_U,KC_WH_U,_______, C(Z),_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,KC_BTN5,KC_MS_L,KC_MS_D,KC_MS_R, F(7),KC_WH_L,KC_WH_D,KC_WH_U,KC_WH_R,_______,_______, _______, _______,_______,_______, \ + MO(MOUSE2),_______, C(Y), C(X), C(C), C(V),_______,KC_BTN2,KC_BTN3,C(PGUP),C(PGDN),_______, KC_RSFT, _______, _______,_______,_______,_______, \ + KC_LCTL,_______,KC_LALT, KC_BTN1, KC_RALT,KC_RGUI, KC_APP,KC_RCTL, _______,_______,_______, _______,_______), /* Layer 5: Mouse layer 2*/ [MOUSE2] = KEYMAP(\ - _______,_______,_______, _______, _______, _______,_______,_______,_______, _______, _______,_______,_______, _______,_______,_______, \ - _______,_______,_______, _______, _______, _______,_______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ - _______,_______,KC_BTN2, KC_WH_U, KC_BTN3, _______,_______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ - _______,_______,KC_WH_L, KC_WH_D, KC_WH_R, _______,KC_MS_L,KC_MS_D,KC_MS_U, KC_MS_R, _______,_______, _______, _______,_______,_______, \ - _______,_______,_______, _______, _______, _______,_______,_______,_______, _______, _______,_______, _______, _______, _______,_______,_______,_______, \ - _______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______), + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,KC_BTN2,KC_WH_U,KC_BTN3,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,KC_WH_L,KC_WH_D,KC_WH_R,_______,KC_MS_L,KC_MS_D,KC_MS_U,KC_MS_R,_______,_______, _______, _______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, _______, _______,_______,_______,_______, \ + _______,_______,_______, _______, _______,_______,_______,_______, _______,_______,_______, _______,_______), /* Layer 6: Misc layer */ [MISC] = KEYMAP(\ - XXXXXXX, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24, XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,KC_SLCT,LC(KC_W), KC_UP, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,KC_BSPC, KC_DEL, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - XXXXXXX,XXXXXXX, KC_LEFT, KC_DOWN, KC_RGHT, XXXXXXX,KC_HOME,KC_PGDN,KC_PGUP, XXXXXXX, XXXXXXX,XXXXXXX, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX, \ - KC_LSFT,XXXXXXX,LC(KC_Y),LC(KC_X),LC(KC_C),LC(KC_V), KC_SPC, KC_END,XXXXXXX,LC(KC_PGUP),LC(KC_PGDN),XXXXXXX, KC_RSFT, XXXXXXX, XXXXXXX,XXXXXXX,XXXXXXX,XXXXXXX, \ - KC_LCTL,KC_LGUI, KC_LALT, LT(MISC, KC_SPC), KC_RALT,KC_RGUI, KC_APP,KC_RCTL, XXXXXXX,XXXXXXX,XXXXXXX, XXXXXXX,XXXXXXX), + _______, KC_F13, KC_F14, KC_F15, KC_F16, KC_F17, KC_F18, KC_F19, KC_F20, KC_F21, KC_F22, KC_F23, KC_F24, _______,_______,_______, \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,KC_SLCT, C(W), KC_UP,_______,_______,_______,_______,KC_BSPC, KC_DEL,_______,_______,_______,_______, _______,_______,_______, _______,_______,_______,_______, \ + _______,_______,KC_LEFT,KC_DOWN,KC_RGHT,_______,KC_HOME,KC_PGDN,KC_PGUP,_______,_______,_______, _______, _______,_______,_______, \ + KC_LSFT,_______, C(Y), C(X), C(C), C(V), KC_SPC, KC_END,_______,C(PGUP),C(PGDN),_______, _______, _______, _______,_______,_______,_______, \ + _______,_______,_______, LT(MISC, KC_SPC), _______,_______,_______,_______, _______,_______,_______, _______,_______), }; const uint16_t PROGMEM fn_actions[] = { - [0] = ACTION_LAYER_TAP_TOGGLE(MOUSE1), // toggle enable mouse layer (4) - [1] = ACTION_FUNCTION_TAP(LCTRL_BRACKET), // tap to print [ - [2] = ACTION_FUNCTION_TAP(RCTRL_BRACKET), // tap to print ] - [3] = ACTION_FUNCTION_TAP(LALT_CURLY), // tap to print { - [4] = ACTION_FUNCTION_TAP(RALT_CURLY), // tap to print } - [5] = ACTION_LAYER_TAP_TOGGLE(PROG1), // toggle programming layer 1 (1) + [0] = ACTION_LAYER_TAP_TOGGLE(MOUSE1), // tap-toggle mouse layer (4) + [1] = ACTION_FUNCTION_TAP(LCTRL_BRACKET), // tap to print [ + [2] = ACTION_FUNCTION_TAP(RCTRL_BRACKET), // tap to print ] + [3] = ACTION_FUNCTION_TAP(LALT_CURLY), // tap to print { + [4] = ACTION_FUNCTION_TAP(RALT_CURLY), // tap to print } + [5] = ACTION_LAYER_TAP_TOGGLE(PROG1), // tap-toggle programming layer 1 [6] = ACTION_LAYER_SET_CLEAR(DEFAULT), [7] = ACTION_FUNCTION_TAP(CTRL_CLICK), - [8] = ACTION_FUNCTION_TAP(LSHFT_PAREN), // tap to print ( - [9] = ACTION_FUNCTION_TAP(RSHFT_PAREN), // tap to print ) + [8] = ACTION_FUNCTION_TAP(LSHFT_PAREN), // tap to print ( + [9] = ACTION_FUNCTION_TAP(RSHFT_PAREN), // tap to print ) }; const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) @@ -126,7 +132,22 @@ void matrix_init_user(void) { } void matrix_scan_user(void) { + uint8_t layer; + layer = biton32(layer_state); + if (current_layer_global != layer) { + current_layer_global = layer; + + // unset CAPSLOCK and SCROLL LOCK LEDs + led_set_kb(host_keyboard_leds() & ~(1<event.pressed) { register_mods(MOD_LSFT); } else { diff --git a/keyboards/kitten_paw/keymaps/ickerwx/readme.md b/keyboards/kitten_paw/keymaps/ickerwx/readme.md new file mode 100644 index 0000000000..0d23be4eac --- /dev/null +++ b/keyboards/kitten_paw/keymaps/ickerwx/readme.md @@ -0,0 +1,18 @@ +# My personal keymap for the Kitten Paw controller + +This keymap only works correctly when you have your OS configured with a German keymap. Use the keymap however you like. It's most likely a living thing that will never be quite finished. + +## Description of the layers +Layer 0 (DEFAULT) works just like you would expect a keyboard to work, mostly, except: +Caps Lock switches to the mouse layer, RGUI and APP are switches to the programming layer and media layer. +Mouse and programming layer switches can be held or double-tapped to lock. +Holding space switches to the MISC layer where I currently accumulate useful shortcuts. +Tapping left and right Shift, Ctrl and Alt will send (), [] and {} respectively. + +Layers 1 and 2 (PROG1 and PROG2) emulate the US layout while still using a German OS keymap setting. I was annoyed of having to change the OS settings every time I wanted to use the US layout for coding, so I made these layers to behave just like the US layout even though the OS still uses German. The shift keys were a bit tricky, I had to use them as MO(PROG2) switches, so to get the actual expected behavior I enable LSFT for almost every keypress on PROG2 in ```process_record_user```. Since the shift keys are MO() function keys, they do not print () at the moment, which sucks. I'm working on it. + +Layer 3 (MEDIA) just has a couple of media keys on it, mainly around the cursor keys and nav key cluster. + +Layers 4 and 5 (MOUSE1 and MOUSE2) are mouse layers. Move the cursor using ESDF, scroll using HJKL, Space for left click, N and M for right and middle click. There's more, look at the keymap. + +Layer 6 is a layer I don't have a good name for, so I call it MISC. You'll find cursor keys at ESDF, other navigation keys around the HJKL cluster and F12 to F24 on the F-keys. For now. \ No newline at end of file diff --git a/keyboards/kitten_paw/kitten_paw.c b/keyboards/kitten_paw/kitten_paw.c index 8713baf433..92f64b06b4 100644 --- a/keyboards/kitten_paw/kitten_paw.c +++ b/keyboards/kitten_paw/kitten_paw.c @@ -4,7 +4,6 @@ void matrix_init_kb(void) { // put your keyboard start-up code here // runs once when the firmware starts up - matrix_init_quantum(); matrix_init_user(); } @@ -12,7 +11,6 @@ void matrix_scan_kb(void) { // put your looping keyboard code here // runs every cycle (a lot) - matrix_scan_quantum(); matrix_scan_user(); } @@ -25,6 +23,21 @@ bool process_record_kb(uint16_t keycode, keyrecord_t *record) { void led_set_kb(uint8_t usb_led) { // put your keyboard LED indicator (ex: Caps Lock LED) toggling code here - + CONFIG_LED_IO; + CONFIG_LED_IO; + print_dec(usb_led); + if (usb_led & (1< - - This program is free software: you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation, either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program. If not, see . -*/ - -#include -#include "stdint.h" -#include "led.h" - -/* LED pin configuration - * - * Scroll Lock PC5 - * Caps Lock PC6 - * Num Lock PB7 - * - */ -void led_set(uint8_t usb_led) { - DDRB |= (1<<7); - DDRC |= (1<<5) | (1<<6); - - if (usb_led & (1<