From d1ea398fb9c4848b74fc3eca40d6078bb529bf0a Mon Sep 17 00:00:00 2001 From: GlenPickle Date: Fri, 16 Feb 2018 11:03:53 -0600 Subject: Added Chimera LS and Chimera Ergo (#2335) * Added Chimera Ortho keymap * added readme * fixed hardware link * Added KC_KEYMAP * resolving conflict * Added Chimera LS and Chimera Ergo * Added rules file * fixed rule files * Added Chimera Ortho keymap * Added KC_KEYMAP * Added Chimera LS and Chimera Ergo * fixed rule files * fixed rule files * fixed image links * Added KC_KEYMAP * Added Chimera LS and Chimera Ergo * Added Chimera Ortho keymap * fixed rule files * fixed rule files * fixed image links * Fixed KEYMAP vs KC_KEYMAP --- keyboards/chimera_ls/rules.mk | 82 +++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 keyboards/chimera_ls/rules.mk (limited to 'keyboards/chimera_ls/rules.mk') diff --git a/keyboards/chimera_ls/rules.mk b/keyboards/chimera_ls/rules.mk new file mode 100644 index 0000000000..af08f7a879 --- /dev/null +++ b/keyboards/chimera_ls/rules.mk @@ -0,0 +1,82 @@ + +OPT_DEFS += -DCHIMERA_LS_PROMICRO +CHIMERA_LS_UPLOAD_COMMAND = while [ ! -r $(USB) ]; do sleep 1; done; \ + avrdude -p $(MCU) -c avr109 -U flash:w:$(TARGET).hex -P $(USB) + +# # project specific files +SRC = matrix.c + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Bootloader +# This definition is optional, and if your keyboard supports multiple bootloaders of +# different sizes, comment this out, and the correct address will be loaded +# automatically (+60). See bootloader.mk for all options. +BOOTLOADER = caterina + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration +CUSTOM_MATRIX = yes # Remote matrix from the wireless bridge +# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE +# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA +# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +# MIDI_ENABLE = YES # MIDI controls +UNICODE_ENABLE = YES # Unicode +# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID + +USB = /dev/ttyACM0 -- cgit v1.2.3