From 099701dd3130d433244b3a4102f36f547aec25ae Mon Sep 17 00:00:00 2001 From: tmk Date: Fri, 16 Jan 2015 10:21:18 +0900 Subject: hhkb: Integrate RN-42 support, remove hhkb_rn42 --- keyboard/hhkb/Makefile.iwrap | 103 ------------------------------------------- 1 file changed, 103 deletions(-) delete mode 100644 keyboard/hhkb/Makefile.iwrap (limited to 'keyboard/hhkb/Makefile.iwrap') diff --git a/keyboard/hhkb/Makefile.iwrap b/keyboard/hhkb/Makefile.iwrap deleted file mode 100644 index 2d9d82c481..0000000000 --- a/keyboard/hhkb/Makefile.iwrap +++ /dev/null @@ -1,103 +0,0 @@ -# -# Makefile for iWRAP -# - - -# Target file name (without extension). -TARGET = hhkb_iwrap - -# Directory common source filess exist -TOP_DIR = ../.. - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = \ - keymap.c \ - matrix.c \ - led.c - -CONFIG_H = config_iwrap.h - - -# V-USB debug level: To use ps2_usart.c level must be 0 -# ps2_usart.c requires USART to receive PS/2 signal. -OPT_DEFS = -DDEBUG_LEVEL=0 - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -MCU = atmega328p - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 12000000 - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=2048 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration -MOUSEKEY_ENABLE = yes # Mouse keys -EXTRAKEY_ENABLE = yes # Audio control and System control -CONSOLE_ENABLE = yes # Console for debug -COMMAND_ENABLE = yes # Commands for debug and configuration -#NKRO_ENABLE = yes # USB Nkey Rollover - - - -#---------------- Programming Options -------------------------- -AVRDUDE = avrdude -# Type: avrdude -c ? to get a full listing. -AVRDUDE_PROGRAMMER = usbasp -AVRDUDE_PORT = -AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex -#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep - -# Uncomment the following if you want avrdude's erase cycle counter. -# Note that this counter needs to be initialized first using -Yn, -# see avrdude manual. -#AVRDUDE_ERASE_COUNTER = -y - -# Uncomment the following if you do /not/ wish a verification to be -# performed after programming the device. -#AVRDUDE_NO_VERIFY = -V - -# Increase verbosity level. Please use this when submitting bug -# reports about avrdude. See -# to submit bug reports. -#AVRDUDE_VERBOSE = -v -v - -#AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) -AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) -AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) - -PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) - - - -# Search Path -VPATH += $(TARGET_DIR) -VPATH += $(TOP_DIR) - -include $(TOP_DIR)/protocol/iwrap.mk -# TODO: to be selectable: V-USB, LUFA or PJRC -#include $(TOP_DIR)/protocol/vusb.mk -include $(TOP_DIR)/common.mk -include $(TOP_DIR)/rules.mk -- cgit v1.2.3