From fce99f38757d7ddbcaada0f5f0157ca24b6162b7 Mon Sep 17 00:00:00 2001 From: Mega Mind <68985133+megamind4089@users.noreply.github.com> Date: Sun, 14 Aug 2022 19:27:26 +0800 Subject: [Controller] Added board config for custom controller STeMCell (#16287) Co-authored-by: Mariappan Ramasamy <947300+Mariappan@users.noreply.github.com> Co-authored-by: Mariappan Ramasamy Co-authored-by: Sadek Baroudi --- docs/feature_converters.md | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) (limited to 'docs/feature_converters.md') diff --git a/docs/feature_converters.md b/docs/feature_converters.md index 569cf0f17d..936ab44559 100644 --- a/docs/feature_converters.md +++ b/docs/feature_converters.md @@ -15,6 +15,7 @@ Currently the following converters are available: | `promicro` | `promicro_rp2040` | | `promicro` | `blok` | | `promicro` | `bit_c_pro` | +| `promicro` | `stemcell` | See below for more in depth information on each converter. @@ -56,6 +57,7 @@ If a board currently supported in QMK uses a [Pro Micro](https://www.sparkfun.co | [SparkFun Pro Micro - RP2040](https://www.sparkfun.com/products/18288) | `promicro_rp2040` | | [Blok](https://boardsource.xyz/store/628b95b494dfa308a6581622) | `blok` | | [Bit-C PRO](https://nullbits.co/bit-c-pro) | `bit_c_pro` | +| [STeMCell](https://github.com/megamind4089/STeMCell) | `stemcell` | Converter summary: @@ -66,6 +68,7 @@ Converter summary: | `promicro_rp2040` | `-e CONVERT_TO=promicro_rp2040` | `CONVERT_TO=promicro_rp2040` | `#ifdef CONVERT_TO_PROMICRO_RP2040` | | `blok` | `-e CONVERT_TO=blok` | `CONVERT_TO=blok` | `#ifdef CONVERT_TO_BLOK` | | `bit_c_pro` | `-e CONVERT_TO=bit_c_pro` | `CONVERT_TO=bit_c_pro` | `#ifdef CONVERT_TO_BIT_C_PRO` | +| `stemcell` | `-e CONVERT_TO=stemcell` | `CONVERT_TO=stemcell` | `#ifdef CONVERT_TO_STEMCELL` | ### Proton C :id=proton_c @@ -99,3 +102,22 @@ The following defaults are based on what has been implemented for [RP2040](platf ### SparkFun Pro Micro - RP2040, Blok, and Bit-C PRO :id=promicro_rp2040 Currently identical to [Adafruit KB2040](#kb2040). + +### STeMCell :id=stemcell + +Feature set currently identical to [Proton C](#proton_c). +There are two versions of STeMCell available, with different pinouts: + - v1.0.0 + - v2.0.0 (pre-release v1.0.1, v1.0.2) +Default official firmware only supports v2.0.0 STeMCell. + +STeMCell has support to swap UART and I2C pins, to enable single-wire uart communication in STM chips. + +The following additional flags has to be used while compiling, based on the pin used for split communication. + +| Split Pin | Compile flags | +|-----------|---------------| +| D3 | -e STMC_US=yes| +| D2 | Not needed | +| D1 | -e STMC_IS=yes| +| D0 | Not needed | -- cgit v1.2.3