From 97ee1be59da06063275d315d1ea5fa4f14eee6b0 Mon Sep 17 00:00:00 2001 From: tmk Date: Thu, 18 Oct 2012 10:41:37 +0900 Subject: Add Sun converter initial files. --- converter/sun_usb/Makefile | 90 ++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 90 insertions(+) create mode 100644 converter/sun_usb/Makefile (limited to 'converter/sun_usb/Makefile') diff --git a/converter/sun_usb/Makefile b/converter/sun_usb/Makefile new file mode 100644 index 0000000000..7c06f26ce8 --- /dev/null +++ b/converter/sun_usb/Makefile @@ -0,0 +1,90 @@ +# +# Makefile for PJRC Teensy +# + + +# Target file name (without extension). +TARGET = sun_usb + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# keyboard dependent files +SRC = keymap.c \ + matrix.c \ + led.c \ + protocol/serial.c + +CONFIG_H = config.h + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +#MCU = at90usb162 # Teensy 1.0 +MCU = atmega32u4 # Teensy 2.0 +#MCU = at90usb646 # Teensy++ 1.0 +#MCU = at90usb1286 # Teensy++ 2.0 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# Build Options +# *Comment out* to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +NKRO_ENABLE = yes # USB Nkey Rollover + + + +#---------------- Programming Options -------------------------- +AVRDUDE = avrdude +# Type: avrdude -c ? to get a full listing. +AVRDUDE_PROGRAMMER = avr109 +AVRDUDE_PORT = /dev/ttyACM0 +AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex +#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep + +# Uncomment the following if you want avrdude's erase cycle counter. +# Note that this counter needs to be initialized first using -Yn, +# see avrdude manual. +#AVRDUDE_ERASE_COUNTER = -y + +# Uncomment the following if you do /not/ wish a verification to be +# performed after programming the device. +#AVRDUDE_NO_VERIFY = -V + +# Increase verbosity level. Please use this when submitting bug +# reports about avrdude. See +# to submit bug reports. +#AVRDUDE_VERBOSE = -v -v + +AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) +#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) +AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) +AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) +AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) + +#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) +#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex +PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + + +include $(TOP_DIR)/protocol/pjrc.mk +include $(TOP_DIR)/protocol.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk -- cgit v1.2.3 From b56717b843859aa3188f9a40532b077241269482 Mon Sep 17 00:00:00 2001 From: tmk Date: Fri, 19 Oct 2012 14:06:18 +0900 Subject: Use software serial for Sun. --- converter/sun_usb/Makefile | 72 +++++++++++++++++++++------------------------- 1 file changed, 32 insertions(+), 40 deletions(-) (limited to 'converter/sun_usb/Makefile') diff --git a/converter/sun_usb/Makefile b/converter/sun_usb/Makefile index 7c06f26ce8..4c79a8d278 100644 --- a/converter/sun_usb/Makefile +++ b/converter/sun_usb/Makefile @@ -1,8 +1,3 @@ -# -# Makefile for PJRC Teensy -# - - # Target file name (without extension). TARGET = sun_usb @@ -16,7 +11,7 @@ TARGET_DIR = . SRC = keymap.c \ matrix.c \ led.c \ - protocol/serial.c + protocol/serial_soft.c CONFIG_H = config.h @@ -37,46 +32,43 @@ MCU = atmega32u4 # Teensy 2.0 F_CPU = 16000000 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + # Build Options # *Comment out* to disable the options. # MOUSEKEY_ENABLE = yes # Mouse keys EXTRAKEY_ENABLE = yes # Audio control and System control -NKRO_ENABLE = yes # USB Nkey Rollover - - - -#---------------- Programming Options -------------------------- -AVRDUDE = avrdude -# Type: avrdude -c ? to get a full listing. -AVRDUDE_PROGRAMMER = avr109 -AVRDUDE_PORT = /dev/ttyACM0 -AVRDUDE_WRITE_FLASH = -U flash:w:$(TARGET).hex -#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep - -# Uncomment the following if you want avrdude's erase cycle counter. -# Note that this counter needs to be initialized first using -Yn, -# see avrdude manual. -#AVRDUDE_ERASE_COUNTER = -y - -# Uncomment the following if you do /not/ wish a verification to be -# performed after programming the device. -#AVRDUDE_NO_VERIFY = -V - -# Increase verbosity level. Please use this when submitting bug -# reports about avrdude. See -# to submit bug reports. -#AVRDUDE_VERBOSE = -v -v +CONSOLE_ENABLE = yes # Console for debug +#NKRO_ENABLE = yes # USB Nkey Rollover -AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER) -#AVRDUDE_FLAGS = -p $(MCU) -c $(AVRDUDE_PROGRAMMER) -AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY) -AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE) -AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER) -#PROGRAM_CMD = $(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM) -#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex -PROGRAM_CMD = dfu-programmer atmega32u4 flash $(TARGET).hex +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOT_SIZE=4096 # Search Path @@ -84,7 +76,7 @@ VPATH += $(TARGET_DIR) VPATH += $(TOP_DIR) -include $(TOP_DIR)/protocol/pjrc.mk +include $(TOP_DIR)/protocol/lufa.mk include $(TOP_DIR)/protocol.mk include $(TOP_DIR)/common.mk include $(TOP_DIR)/rules.mk -- cgit v1.2.3