diff options
Diffstat (limited to 'ps2_vusb/Makefile.orig')
| -rw-r--r-- | ps2_vusb/Makefile.orig | 165 |
1 files changed, 0 insertions, 165 deletions
diff --git a/ps2_vusb/Makefile.orig b/ps2_vusb/Makefile.orig deleted file mode 100644 index 2bd1ed584e..0000000000 --- a/ps2_vusb/Makefile.orig +++ /dev/null @@ -1,165 +0,0 @@ -# Name: Makefile -# Project: hid-mouse example -# Author: Christian Starkjohann -# Creation Date: 2008-04-07 -# Tabsize: 4 -# Copyright: (c) 2008 by OBJECTIVE DEVELOPMENT Software GmbH -# License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt) -# This Revision: $Id: Makefile 692 2008-11-07 15:07:40Z cs $ - -DEVICE = atmega168 -F_CPU = 16000000 # in Hz -FUSE_L = # see below for fuse values for particular devices -FUSE_H = -#AVRDUDE = avrdude -c usbasp -p $(DEVICE) # edit this line for your programmer -AVRDUDE = avrdude -P COM1 -b 19200 -c arduino -p $(DEVICE) - -CFLAGS = -Iusbdrv -I. -DDEBUG_LEVEL=1 -OBJECTS = usbdrv/usbdrv.o usbdrv/usbdrvasm.o usbdrv/oddebug.o main.o - -COMPILE = avr-gcc -Wall -Os -DF_CPU=$(F_CPU) $(CFLAGS) -mmcu=$(DEVICE) - -############################################################################## -# Fuse values for particular devices -############################################################################## -# If your device is not listed here, go to -# http://palmavr.sourceforge.net/cgi-bin/fc.cgi -# and choose options for external crystal clock and no clock divider -# -################################## ATMega8 ################################## -# ATMega8 FUSE_L (Fuse low byte): -# 0x9f = 1 0 0 1 1 1 1 1 -# ^ ^ \ / \--+--/ -# | | | +------- CKSEL 3..0 (external >8M crystal) -# | | +--------------- SUT 1..0 (crystal osc, BOD enabled) -# | +------------------ BODEN (BrownOut Detector enabled) -# +-------------------- BODLEVEL (2.7V) -# ATMega8 FUSE_H (Fuse high byte): -# 0xc9 = 1 1 0 0 1 0 0 1 <-- BOOTRST (boot reset vector at 0x0000) -# ^ ^ ^ ^ ^ ^ ^------ BOOTSZ0 -# | | | | | +-------- BOOTSZ1 -# | | | | + --------- EESAVE (don't preserve EEPROM over chip erase) -# | | | +-------------- CKOPT (full output swing) -# | | +---------------- SPIEN (allow serial programming) -# | +------------------ WDTON (WDT not always on) -# +-------------------- RSTDISBL (reset pin is enabled) -# -############################## ATMega48/88/168 ############################## -# ATMega*8 FUSE_L (Fuse low byte): -# 0xdf = 1 1 0 1 1 1 1 1 -# ^ ^ \ / \--+--/ -# | | | +------- CKSEL 3..0 (external >8M crystal) -# | | +--------------- SUT 1..0 (crystal osc, BOD enabled) -# | +------------------ CKOUT (if 0: Clock output enabled) -# +-------------------- CKDIV8 (if 0: divide by 8) -# ATMega*8 FUSE_H (Fuse high byte): -# 0xde = 1 1 0 1 1 1 1 0 -# ^ ^ ^ ^ ^ \-+-/ -# | | | | | +------ BODLEVEL 0..2 (110 = 1.8 V) -# | | | | + --------- EESAVE (preserve EEPROM over chip erase) -# | | | +-------------- WDTON (if 0: watchdog always on) -# | | +---------------- SPIEN (allow serial programming) -# | +------------------ DWEN (debug wire enable) -# +-------------------- RSTDISBL (reset pin is enabled) -# -############################## ATTiny25/45/85 ############################### -# ATMega*5 FUSE_L (Fuse low byte): -# 0xef = 1 1 1 0 1 1 1 1 -# ^ ^ \+/ \--+--/ -# | | | +------- CKSEL 3..0 (clock selection -> crystal @ 12 MHz) -# | | +--------------- SUT 1..0 (BOD enabled, fast rising power) -# | +------------------ CKOUT (clock output on CKOUT pin -> disabled) -# +-------------------- CKDIV8 (divide clock by 8 -> don't divide) -# ATMega*5 FUSE_H (Fuse high byte): -# 0xdd = 1 1 0 1 1 1 0 1 -# ^ ^ ^ ^ ^ \-+-/ -# | | | | | +------ BODLEVEL 2..0 (brownout trigger level -> 2.7V) -# | | | | +---------- EESAVE (preserve EEPROM on Chip Erase -> not preserved) -# | | | +-------------- WDTON (watchdog timer always on -> disable) -# | | +---------------- SPIEN (enable serial programming -> enabled) -# | +------------------ DWEN (debug wire enable) -# +-------------------- RSTDISBL (disable external reset -> enabled) -# -################################ ATTiny2313 ################################# -# ATTiny2313 FUSE_L (Fuse low byte): -# 0xef = 1 1 1 0 1 1 1 1 -# ^ ^ \+/ \--+--/ -# | | | +------- CKSEL 3..0 (clock selection -> crystal @ 12 MHz) -# | | +--------------- SUT 1..0 (BOD enabled, fast rising power) -# | +------------------ CKOUT (clock output on CKOUT pin -> disabled) -# +-------------------- CKDIV8 (divide clock by 8 -> don't divide) -# ATTiny2313 FUSE_H (Fuse high byte): -# 0xdb = 1 1 0 1 1 0 1 1 -# ^ ^ ^ ^ \-+-/ ^ -# | | | | | +---- RSTDISBL (disable external reset -> enabled) -# | | | | +-------- BODLEVEL 2..0 (brownout trigger level -> 2.7V) -# | | | +-------------- WDTON (watchdog timer always on -> disable) -# | | +---------------- SPIEN (enable serial programming -> enabled) -# | +------------------ EESAVE (preserve EEPROM on Chip Erase -> not preserved) -# +-------------------- DWEN (debug wire enable) - - -# symbolic targets: -help: - @echo "This Makefile has no default rule. Use one of the following:" - @echo "make hex ....... to build main.hex" - @echo "make program ... to flash fuses and firmware" - @echo "make fuse ...... to flash the fuses" - @echo "make flash ..... to flash the firmware (use this on metaboard)" - @echo "make clean ..... to delete objects and hex file" - -hex: main.hex - -program: flash fuse - -# rule for programming fuse bits: -fuse: - @[ "$(FUSE_H)" != "" -a "$(FUSE_L)" != "" ] || \ - { echo "*** Edit Makefile and choose values for FUSE_L and FUSE_H!"; exit 1; } - $(AVRDUDE) -U hfuse:w:$(FUSE_H):m -U lfuse:w:$(FUSE_L):m - -# rule for uploading firmware: -flash: main.hex - $(AVRDUDE) -U flash:w:main.hex:i - -# rule for deleting dependent files (those which can be built by Make): -clean: - rm -f main.hex main.lst main.obj main.cof main.list main.map main.eep.hex main.elf *.o usbdrv/*.o main.s usbdrv/oddebug.s usbdrv/usbdrv.s - -# Generic rule for compiling C files: -.c.o: - $(COMPILE) -c $< -o $@ - -# Generic rule for assembling Assembler source files: -.S.o: - $(COMPILE) -x assembler-with-cpp -c $< -o $@ -# "-x assembler-with-cpp" should not be necessary since this is the default -# file type for the .S (with capital S) extension. However, upper case -# characters are not always preserved on Windows. To ensure WinAVR -# compatibility define the file type manually. - -# Generic rule for compiling C to assembler, used for debugging only. -.c.s: - $(COMPILE) -S $< -o $@ - -# file targets: - -# Since we don't want to ship the driver multipe times, we copy it into this project: -usbdrv: - cp -r ../usbdrv . - -main.elf: usbdrv $(OBJECTS) # usbdrv dependency only needed because we copy it - $(COMPILE) -o main.elf $(OBJECTS) - -main.hex: main.elf - rm -f main.hex main.eep.hex - avr-objcopy -j .text -j .data -O ihex main.elf main.hex - avr-size main.hex - -# debugging targets: - -disasm: main.elf - avr-objdump -d main.elf - -cpp: - $(COMPILE) -E main.c |