diff options
Diffstat (limited to 'keyboards/kbd67/rules.mk')
| -rw-r--r-- | keyboards/kbd67/rules.mk | 80 |
1 files changed, 0 insertions, 80 deletions
diff --git a/keyboards/kbd67/rules.mk b/keyboards/kbd67/rules.mk deleted file mode 100644 index 65c82dd7f5..0000000000 --- a/keyboards/kbd67/rules.mk +++ /dev/null @@ -1,80 +0,0 @@ -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Bootloader selection -# Teensy halfkay -# Pro Micro caterina -# Atmel DFU atmel-dfu -# LUFA DFU lufa-dfu -# QMK DFU qmk-dfu -# atmega32a bootloadHID -BOOTLOADER = atmel-dfu - - -# If you don't know the bootloader type, then you can specify the -# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -# OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# change yes to no to disable -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = yes # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -NKRO_ENABLE = no # USB Nkey Rollover -BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality on B7 by default -RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow -MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config) -UNICODE_ENABLE = no # Unicode -BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID -AUDIO_ENABLE = no # Audio output on port C6 -FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches -HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400) |