diff options
Diffstat (limited to 'keyboards/gh60')
| -rw-r--r-- | keyboards/gh60/revc/keymaps/bluezio/rules.mk | 69 | ||||
| -rw-r--r-- | keyboards/gh60/revc/keymaps/dbroqua/config.h | 153 | ||||
| -rw-r--r-- | keyboards/gh60/revc/keymaps/dbroqua/rules.mk | 109 | ||||
| -rw-r--r-- | keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk | 108 | ||||
| -rw-r--r-- | keyboards/gh60/revc/keymaps/robotmaxtron/config.h | 156 | ||||
| -rw-r--r-- | keyboards/gh60/revc/keymaps/robotmaxtron/rules.mk | 108 |
6 files changed, 9 insertions, 694 deletions
diff --git a/keyboards/gh60/revc/keymaps/bluezio/rules.mk b/keyboards/gh60/revc/keymaps/bluezio/rules.mk index 4b820c974b..116d505b7e 100644 --- a/keyboards/gh60/revc/keymaps/bluezio/rules.mk +++ b/keyboards/gh60/revc/keymaps/bluezio/rules.mk @@ -1,68 +1 @@ -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -# CONSOLE_ENABLE = yes # Console for debug(+400) -# COMMAND_ENABLE = yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -# MIDI_ENABLE = YES # MIDI controls -# UNICODE_ENABLE = YES # Unicode -# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID -KEY_LOCK_ENABLE = yes # KC_LOCK - -LAYOUTS = 60_ansi 60_iso 60_ansi_split_bs_rshift +KEY_LOCK_ENABLE = yes diff --git a/keyboards/gh60/revc/keymaps/dbroqua/config.h b/keyboards/gh60/revc/keymaps/dbroqua/config.h index 5d1a777a4b..38e5bb0def 100644 --- a/keyboards/gh60/revc/keymaps/dbroqua/config.h +++ b/keyboards/gh60/revc/keymaps/dbroqua/config.h @@ -15,160 +15,11 @@ You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ -#ifndef CONFIG_USER_H -#define CONFIG_USER_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0001 -#define MANUFACTURER geekhack -#define PRODUCT GH60 - -/* key matrix size */ -#define MATRIX_ROWS 5 -#define MATRIX_COLS 14 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * -*/ -#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } -#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } -#define UNUSED_PINS - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCE 5 - -/* define if matrix has ghost (lacks anti-ghosting diodes) */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 3 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -/* - * Force NKRO - * - * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved - * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the - * makefile for this to work.) - * - * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) - * until the next keyboard reset. - * - * NKRO may prevent your keystrokes from being detected in the BIOS, but it is - * fully operational during normal computer usage. - * - * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) - * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by - * bootmagic, NKRO mode will always be enabled until it is toggled again during a - * power-up. - * - */ -//#define FORCE_NKRO - -/* - * Magic Key Options - * - * Magic keys are hotkey commands that allow control over firmware functions of - * the keyboard. They are best used in combination with the HID Listen program, - * found here: https://www.pjrc.com/teensy/hid_listen.html - * - * The options below allow the magic key functionality to be changed. This is - * useful if your keyboard/keypad is missing keys and you want magic key support. - * - */ - -/* control how magic key switches layers */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false - -/* override magic key keymap */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM -//#define MAGIC_KEY_HELP1 H -//#define MAGIC_KEY_HELP2 SLASH -//#define MAGIC_KEY_DEBUG D -//#define MAGIC_KEY_DEBUG_MATRIX X -//#define MAGIC_KEY_DEBUG_KBD K -//#define MAGIC_KEY_DEBUG_MOUSE M -//#define MAGIC_KEY_VERSION V -//#define MAGIC_KEY_STATUS S -//#define MAGIC_KEY_CONSOLE C -//#define MAGIC_KEY_LAYER0_ALT1 ESC -//#define MAGIC_KEY_LAYER0_ALT2 GRAVE -//#define MAGIC_KEY_LAYER0 0 -//#define MAGIC_KEY_LAYER1 1 -//#define MAGIC_KEY_LAYER2 2 -//#define MAGIC_KEY_LAYER3 3 -//#define MAGIC_KEY_LAYER4 4 -//#define MAGIC_KEY_LAYER5 5 -//#define MAGIC_KEY_LAYER6 6 -//#define MAGIC_KEY_LAYER7 7 -//#define MAGIC_KEY_LAYER8 8 -//#define MAGIC_KEY_LAYER9 9 -//#define MAGIC_KEY_BOOTLOADER PAUSE -//#define MAGIC_KEY_LOCK CAPS -//#define MAGIC_KEY_EEPROM E -//#define MAGIC_KEY_NKRO N -//#define MAGIC_KEY_SLEEP_LED Z - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT -//#define NO_ACTION_MACRO -//#define NO_ACTION_FUNCTION - -/* - * RGB Underglow - * These settings are for the F4 by default: - * - * - * #define ws2812_pin PF4 - * #define RGBLED_NUM 14 // Number of LEDs - * #define RGBLIGHT_HUE_STEP 10 - * #define RGBLIGHT_SAT_STEP 17 - * #define RGBLIGHT_VAL_STEP 17 - * - * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. - * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. - * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c -*/ +#pragma once #define RGB_DI_PIN F4 +#define RGBLED_NUM 11 #define RGBLIGHT_ANIMATIONS -#define RGBLED_NUM 11 // Number of LEDs #define RGBLIGHT_HUE_STEP 8 #define RGBLIGHT_SAT_STEP 8 #define RGBLIGHT_VAL_STEP 8 -#endif diff --git a/keyboards/gh60/revc/keymaps/dbroqua/rules.mk b/keyboards/gh60/revc/keymaps/dbroqua/rules.mk index 21d4b60d96..b56ad10c50 100644 --- a/keyboards/gh60/revc/keymaps/dbroqua/rules.mk +++ b/keyboards/gh60/revc/keymaps/dbroqua/rules.mk @@ -1,107 +1,2 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -# CONSOLE_ENABLE = yes # Console for debug(+400) -# COMMAND_ENABLE = yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -# MIDI_ENABLE = YES # MIDI controls -# UNICODE_ENABLE = YES # Unicode -# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = yes # Enable RGB Underglow - +SLEEP_LED_ENABLE = yes +RGBLIGHT_ENABLE = yes diff --git a/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk b/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk index 21192b1794..9e00b7531a 100644 --- a/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk +++ b/keyboards/gh60/revc/keymaps/dbroqua_7U/rules.mk @@ -1,107 +1 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -# CONSOLE_ENABLE = yes # Console for debug(+400) -# COMMAND_ENABLE = yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -# MIDI_ENABLE = YES # MIDI controls -# UNICODE_ENABLE = YES # Unicode -# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = no # Enable RGB Underglow - +SLEEP_LED_ENABLE = yes diff --git a/keyboards/gh60/revc/keymaps/robotmaxtron/config.h b/keyboards/gh60/revc/keymaps/robotmaxtron/config.h index 7cfcf8d453..955ead1ba2 100644 --- a/keyboards/gh60/revc/keymaps/robotmaxtron/config.h +++ b/keyboards/gh60/revc/keymaps/robotmaxtron/config.h @@ -15,163 +15,11 @@ You should have received a copy of the GNU General Public License along with this program. If not, see <http://www.gnu.org/licenses/>. */ -#ifndef CONFIG_USER_H -#define CONFIG_USER_H - -#include "config_common.h" - -/* USB Device descriptor parameter */ -#define VENDOR_ID 0xFEED -#define PRODUCT_ID 0x6060 -#define DEVICE_VER 0x0001 -#define MANUFACTURER geekhack -#define PRODUCT GH60 - -/* key matrix size */ -#define MATRIX_ROWS 5 -#define MATRIX_COLS 14 - -/* - * Keyboard Matrix Assignments - * - * Change this to how you wired your keyboard - * COLS: AVR pins used for columns, left to right - * ROWS: AVR pins used for rows, top to bottom - * DIODE_DIRECTION: COL2ROW = COL = Anode (+), ROW = Cathode (-, marked on diode) - * ROW2COL = ROW = Anode (+), COL = Cathode (-, marked on diode) - * -*/ - #define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } -// Rev A -// #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B0, B5, B4, D7, D6, B3 } -// Rev B/C - #define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B6, D4, B1, B7, B5, B4, D7, D6, B3 } -#define UNUSED_PINS - -/* COL2ROW or ROW2COL */ -#define DIODE_DIRECTION COL2ROW - -/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */ -#define DEBOUNCE 5 - -/* define if matrix has ghost (lacks anti-ghosting diodes) */ -//#define MATRIX_HAS_GHOST - -/* number of backlight levels */ -#define BACKLIGHT_LEVELS 3 - -/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ -#define LOCKING_SUPPORT_ENABLE -/* Locking resynchronize hack */ -#define LOCKING_RESYNC_ENABLE - -/* - * Force NKRO - * - * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved - * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the - * makefile for this to work.) - * - * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N) - * until the next keyboard reset. - * - * NKRO may prevent your keystrokes from being detected in the BIOS, but it is - * fully operational during normal computer usage. - * - * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N) - * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by - * bootmagic, NKRO mode will always be enabled until it is toggled again during a - * power-up. - * - */ -//#define FORCE_NKRO - -/* - * Magic Key Options - * - * Magic keys are hotkey commands that allow control over firmware functions of - * the keyboard. They are best used in combination with the HID Listen program, - * found here: https://www.pjrc.com/teensy/hid_listen.html - * - * The options below allow the magic key functionality to be changed. This is - * useful if your keyboard/keypad is missing keys and you want magic key support. - * - */ - -/* control how magic key switches layers */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS true -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM false - -/* override magic key keymap */ -//#define MAGIC_KEY_SWITCH_LAYER_WITH_FKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_NKEYS -//#define MAGIC_KEY_SWITCH_LAYER_WITH_CUSTOM -//#define MAGIC_KEY_HELP1 H -//#define MAGIC_KEY_HELP2 SLASH -//#define MAGIC_KEY_DEBUG D -//#define MAGIC_KEY_DEBUG_MATRIX X -//#define MAGIC_KEY_DEBUG_KBD K -//#define MAGIC_KEY_DEBUG_MOUSE M -//#define MAGIC_KEY_VERSION V -//#define MAGIC_KEY_STATUS S -//#define MAGIC_KEY_CONSOLE C -//#define MAGIC_KEY_LAYER0_ALT1 ESC -//#define MAGIC_KEY_LAYER0_ALT2 GRAVE -//#define MAGIC_KEY_LAYER0 0 -//#define MAGIC_KEY_LAYER1 1 -//#define MAGIC_KEY_LAYER2 2 -//#define MAGIC_KEY_LAYER3 3 -//#define MAGIC_KEY_LAYER4 4 -//#define MAGIC_KEY_LAYER5 5 -//#define MAGIC_KEY_LAYER6 6 -//#define MAGIC_KEY_LAYER7 7 -//#define MAGIC_KEY_LAYER8 8 -//#define MAGIC_KEY_LAYER9 9 -//#define MAGIC_KEY_BOOTLOADER PAUSE -//#define MAGIC_KEY_LOCK CAPS -//#define MAGIC_KEY_EEPROM E -//#define MAGIC_KEY_NKRO N -//#define MAGIC_KEY_SLEEP_LED Z - -/* - * Feature disable options - * These options are also useful to firmware size reduction. - */ - -/* disable debug print */ -//#define NO_DEBUG - -/* disable print */ -//#define NO_PRINT - -/* disable action features */ -//#define NO_ACTION_LAYER -//#define NO_ACTION_TAPPING -//#define NO_ACTION_ONESHOT -//#define NO_ACTION_MACRO -//#define NO_ACTION_FUNCTION - -/* - * RGB Underglow - * These settings are for the F4 by default: - * - * - * #define ws2812_pin PF4 - * #define RGBLED_NUM 14 // Number of LEDs - * #define RGBLIGHT_HUE_STEP 10 - * #define RGBLIGHT_SAT_STEP 17 - * #define RGBLIGHT_VAL_STEP 17 - * - * The firmware supports 5 different light effects, and the color (hue, saturation, brightness) can be customized in most effects. - * To control the underglow, you need to modify your keymap file to assign those functions to some keys/key combinations. - * For details, please check this keymap. keyboard/planck/keymaps/yang/keymap.c -*/ +#pragma once #define RGB_DI_PIN F4 +#define RGBLED_NUM 8 #define RGBLIGHT_ANIMATIONS -#define RGBLED_NUM 8 // Number of LEDs #define RGBLIGHT_HUE_STEP 8 #define RGBLIGHT_SAT_STEP 8 #define RGBLIGHT_VAL_STEP 8 -#endif diff --git a/keyboards/gh60/revc/keymaps/robotmaxtron/rules.mk b/keyboards/gh60/revc/keymaps/robotmaxtron/rules.mk index b6761ac9ff..1e3cebb145 100644 --- a/keyboards/gh60/revc/keymaps/robotmaxtron/rules.mk +++ b/keyboards/gh60/revc/keymaps/robotmaxtron/rules.mk @@ -1,107 +1 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make all = Make software. -# -# make clean = Clean out built project files. -# -# make coff = Convert ELF to AVR COFF. -# -# make extcoff = Convert ELF to AVR Extended COFF. -# -# make program = Download the hex file to the device. -# Please customize your programmer settings(PROGRAM_CMD) -# -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -# make dfu = Download the hex file to the device, using dfu-programmer (must -# have dfu-programmer installed). -# -# make flip = Download the hex file to the device, using Atmel FLIP (must -# have Atmel FLIP installed). -# -# make dfu-ee = Download the eeprom file to the device, using dfu-programmer -# (must have dfu-programmer installed). -# -# make flip-ee = Download the eeprom file to the device, using Atmel FLIP -# (must have Atmel FLIP installed). -# -# make debug = Start either simulavr or avarice as specified for debugging, -# with avr-gdb or avr-insight as the front end for debugging. -# -# make filename.s = Just compile filename.c into the assembler code only. -# -# make filename.i = Create a preprocessed source file for use in submitting -# bug reports to the GCC project. -# -# To rebuild project do "make clean" then "make all". -#---------------------------------------------------------------------------- - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -# CONSOLE_ENABLE = yes # Console for debug(+400) -# COMMAND_ENABLE = yes # Commands for debug and configuration -KEYBOARD_LOCK_ENABLE = yes # Allow locking of keyboard via magic key -# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE -# SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work -# BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality -# MIDI_ENABLE = YES # MIDI controls -# UNICODE_ENABLE = YES # Unicode -# BLUETOOTH_ENABLE = yes # Enable Bluetooth with the Adafruit EZ-Key HID -RGBLIGHT_ENABLE = yes # Enable RGB Underglow - +RGBLIGHT_ENABLE = yes |