diff options
Diffstat (limited to 'keyboards/ergodox/ergodone/rules.mk')
| -rw-r--r-- | keyboards/ergodox/ergodone/rules.mk | 91 |
1 files changed, 0 insertions, 91 deletions
diff --git a/keyboards/ergodox/ergodone/rules.mk b/keyboards/ergodox/ergodone/rules.mk deleted file mode 100644 index e7fd4e0aba..0000000000 --- a/keyboards/ergodox/ergodone/rules.mk +++ /dev/null @@ -1,91 +0,0 @@ -#---------------------------------------------------------------------------- -# On command line: -# -# make = Make software. -# -# make clean = Clean out built project files. -# -# That's pretty much all you need. To compile, always go make clean, -# followed by make. -# -# For advanced users only: -# make teensy = Download the hex file to the device, using teensy_loader_cli. -# (must have teensy_loader_cli installed). -# -#---------------------------------------------------------------------------- - -# # project specific files -SRC = \ - twimaster.c \ - matrix.c \ - expander.c \ - -# MCU name -MCU = atmega32u4 - -# Processor frequency. -# This will define a symbol, F_CPU, in all source code files equal to the -# processor frequency in Hz. You can then use this symbol in your source code to -# calculate timings. Do NOT tack on a 'UL' at the end, this will be done -# automatically to create a 32-bit value in your source code. -# -# This will be an integer division of F_USB below, as it is sourced by -# F_USB after it has run through any CPU prescalers. Note that this value -# does not *change* the processor frequency - it should merely be updated to -# reflect the processor speed set externally so that the code can use accurate -# software delays. -F_CPU = 16000000 - -# -# LUFA specific -# -# Target architecture (see library "Board Types" documentation). -ARCH = AVR8 - -# Input clock frequency. -# This will define a symbol, F_USB, in all source code files equal to the -# input clock frequency (before any prescaling is performed) in Hz. This value may -# differ from F_CPU if prescaling is used on the latter, and is required as the -# raw input clock is fed directly to the PLL sections of the AVR for high speed -# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' -# at the end, this will be done automatically to create a 32-bit value in your -# source code. -# -# If no clock division is performed on the input clock inside the AVR (via the -# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. -F_USB = $(F_CPU) - -# Interrupt driven control endpoint task(+60) -OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT - - -# Boot Section Size in *bytes* -# Teensy halfKay 512 -# Teensy++ halfKay 1024 -# Atmel DFU loader 4096 -# LUFA bootloader 4096 -# USBaspLoader 2048 -OPT_DEFS += -DBOOTLOADER_SIZE=4096 - -# Build Options -# comment out to disable the options. -# -BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -MOUSEKEY_ENABLE = yes # Mouse keys(+4700) -EXTRAKEY_ENABLE = yes # Audio control and System control(+450) -CONSOLE_ENABLE = no # Console for debug(+400) -COMMAND_ENABLE = no # Commands for debug and configuration -SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend -NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA -USB_6KRO_ENABLE = no # USB 6key Rollover -BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality -KEYMAP_IN_EEPROM_ENABLE = no # External keymap in eeprom -KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor -SOFTPWM_LED_ENABLE = no # Enable SoftPWM to drive backlight -FADING_LED_ENABLE = no # Enable fading backlight -BREATHING_LED_ENABLE = no # Enable breathing backlight -LEDMAP_ENABLE = no # Enable LED mapping -LEDMAP_IN_EEPROM_ENABLE = no # Read LED mapping from eeprom -ONEHAND_ENABLE = no # Disable Onehand -RGBLIGHT_ENABLE = no -MIDI_ENABLE = no |