diff options
Diffstat (limited to 'keyboard')
| l---------[-rw-r--r--] | keyboard/hbkb/Makefile | 57 | ||||
| -rw-r--r-- | keyboard/hbkb/Makefile.lufa | 119 | ||||
| -rw-r--r-- | keyboard/hbkb/Makefile.pjrc (renamed from keyboard/macway/Makefile) | 7 | ||||
| -rw-r--r-- | keyboard/hbkb/config.h | 3 | ||||
| -rw-r--r-- | keyboard/hhkb/Makefile.lufa | 119 | ||||
| -rw-r--r-- | keyboard/hhkb/Makefile.pjrc | 7 | ||||
| -rw-r--r-- | keyboard/hhkb/config.h (renamed from keyboard/hhkb/config_pjrc.h) | 5 | ||||
| -rw-r--r-- | keyboard/hhkb/keymap.c | 2 | ||||
| -rw-r--r-- | keyboard/hhkb/matrix.c | 10 | ||||
| -rw-r--r-- | keyboard/macway/Makefile.lufa | 119 | ||||
| -rw-r--r-- | keyboard/macway/Makefile.pjrc | 95 | ||||
| -rw-r--r-- | keyboard/macway/config.h | 6 | ||||
| -rw-r--r-- | keyboard/macway/keymap.c | 10 |
13 files changed, 487 insertions, 72 deletions
diff --git a/keyboard/hbkb/Makefile b/keyboard/hbkb/Makefile index 26be322e01..f00d036da3 100644..120000 --- a/keyboard/hbkb/Makefile +++ b/keyboard/hbkb/Makefile @@ -1,56 +1 @@ -# Target file name (without extension). -TARGET = hbk - -# Directory common source filess exist -TOP_DIR = ../.. - -# Directory keyboard dependent files exist -TARGET_DIR = . - -# keyboard dependent files -SRC = main.c \ - keymap.c \ - matrix.c \ - led.c - -CONFIG_H = config.h - - -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 - - -# Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. -F_CPU = 16000000 - - -# Build Options -# comment out to disable the options. -# -MOUSEKEY_ENABLE = yes # Mouse keys -#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support -EXTRAKEY_ENABLE = yes # Audio control and System control -#NKRO_ENABLE = yes # USB Nkey Rollover - - - -#---------------- Programming Options -------------------------- -#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex -PROGRAM_CMD = /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) erase && \ - /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) flash $(TARGET).hex && \ - /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) start - - - -include $(TOP_DIR)/protocol/pjrc.mk -include $(TOP_DIR)/protocol.mk -include $(TOP_DIR)/common.mk -include $(TOP_DIR)/rules.mk +Makefile.lufa
\ No newline at end of file diff --git a/keyboard/hbkb/Makefile.lufa b/keyboard/hbkb/Makefile.lufa new file mode 100644 index 0000000000..c73a0ca7d1 --- /dev/null +++ b/keyboard/hbkb/Makefile.lufa @@ -0,0 +1,119 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = hbkb_lufa + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + + +# List C source files here. (C dependencies are automatically generated.) +SRC += keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support + + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +OPT_DEFS += -DBOOT_SIZE=4096 + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/lufa.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk diff --git a/keyboard/macway/Makefile b/keyboard/hbkb/Makefile.pjrc index afee38b120..159f56b44b 100644 --- a/keyboard/macway/Makefile +++ b/keyboard/hbkb/Makefile.pjrc @@ -1,5 +1,5 @@ # Target file name (without extension). -TARGET = macway +TARGET = hbkb # Directory common source filess exist TOP_DIR = ../.. @@ -43,7 +43,10 @@ EXTRAKEY_ENABLE = yes # Audio control and System control #---------------- Programming Options -------------------------- -PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex +#PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex +PROGRAM_CMD = /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) erase && \ + /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) flash $(TARGET).hex && \ + /opt/dfu-programmer-0.5.2/bin/dfu-programmer $(MCU) start diff --git a/keyboard/hbkb/config.h b/keyboard/hbkb/config.h index 5262399dc3..deaabb2495 100644 --- a/keyboard/hbkb/config.h +++ b/keyboard/hbkb/config.h @@ -24,7 +24,10 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. #define VENDOR_ID 0xFEED #define PRODUCT_ID 0xBB00 #define MANUFACTURER t.m.k. +#define DEVICE_VER 0x0100 #define PRODUCT Happy Buckling Keyboard + + #define DESCRIPTION mod version of IBM Model M keyboard diff --git a/keyboard/hhkb/Makefile.lufa b/keyboard/hhkb/Makefile.lufa new file mode 100644 index 0000000000..cdd68f40ab --- /dev/null +++ b/keyboard/hhkb/Makefile.lufa @@ -0,0 +1,119 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = hhkb_lufa + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + + +# List C source files here. (C dependencies are automatically generated.) +SRC += keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name +MCU = at90usb1286 +#MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support + + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +#OPT_DEFS += -DBOOT_SIZE=4096 + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/lufa.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk diff --git a/keyboard/hhkb/Makefile.pjrc b/keyboard/hhkb/Makefile.pjrc index f6d133eae4..f8836a2ca1 100644 --- a/keyboard/hhkb/Makefile.pjrc +++ b/keyboard/hhkb/Makefile.pjrc @@ -13,12 +13,11 @@ TOP_DIR = ../.. TARGET_DIR = . # keyboard dependent files -SRC = main.c \ - keymap.c \ +SRC = keymap.c \ matrix.c \ led.c -CONFIG_H = config_pjrc.h +CONFIG_H = config.h # MCU name, you MUST set this to match the board you are using @@ -53,8 +52,8 @@ PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex # Search Path VPATH = $(TARGET_DIR) +VPATH = $(TOP_DIR) include $(TOP_DIR)/protocol/pjrc.mk -include $(TOP_DIR)/protocol.mk include $(TOP_DIR)/common.mk include $(TOP_DIR)/rules.mk diff --git a/keyboard/hhkb/config_pjrc.h b/keyboard/hhkb/config.h index fffe3522c7..91446466fe 100644 --- a/keyboard/hhkb/config_pjrc.h +++ b/keyboard/hhkb/config.h @@ -21,11 +21,14 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* controller configuration */ #include "controller_teensy.h" + #define VENDOR_ID 0xFEED -#define PRODUCT_ID 0xCAFE +#define PRODUCT_ID 0xCAFF #define DEVICE_VER 0x0101 #define MANUFACTURER t.m.k. #define PRODUCT HHKB mod + + #define DESCRIPTION t.m.k. keyboard firmware for HHKB mod diff --git a/keyboard/hhkb/keymap.c b/keyboard/hhkb/keymap.c index 85a7c31b7e..88a6737ba2 100644 --- a/keyboard/hhkb/keymap.c +++ b/keyboard/hhkb/keymap.c @@ -110,7 +110,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * |Gui |Alt |Space |Alt |xxx| * `--------------------------------------------' */ - KEYMAP(ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \ + KEYMAP(PWR, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, INS, DEL, \ CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,BRK, UP, NO, BSPC, \ LCTL,VOLD,VOLU,MUTE,NO, NO, PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \ LSFT,NO, NO, NO, NO, NO, PPLS,PMNS,END, PGDN,DOWN,RSFT,FN1, \ diff --git a/keyboard/hhkb/matrix.c b/keyboard/hhkb/matrix.c index 350066b904..79d2d98731 100644 --- a/keyboard/hhkb/matrix.c +++ b/keyboard/hhkb/matrix.c @@ -68,8 +68,8 @@ static bool matrix_has_ghost_in_row(uint8_t row); // key: on: 0/off: 1 // prev: unknown: output previous key state(negated)? -#ifdef HOST_PJRC -// Ports for Teensy +#if defined(__AVR_AT90USB1286__) +// Ports for Teensy++ // row: PB0-2 // col: PB3-5,6 // key: PE6(pull-uped) @@ -90,7 +90,8 @@ static bool matrix_has_ghost_in_row(uint8_t row); #define KEY_PREV_OFF() (PORTE &= ~(1<<7)) #define KEY_POWER_ON() #define KEY_POWER_OFF() -#else + +#elif defined(__AVR_ATmega328P__) // Ports for V-USB // key: PB0(pull-uped) // prev: PB1 @@ -126,6 +127,9 @@ static bool matrix_has_ghost_in_row(uint8_t row); DDRC &= ~0x0F; \ PORTC &= ~0x0F; \ } while (0) + +#else +# error "define code for matrix scan" #endif diff --git a/keyboard/macway/Makefile.lufa b/keyboard/macway/Makefile.lufa new file mode 100644 index 0000000000..9c9388ee20 --- /dev/null +++ b/keyboard/macway/Makefile.lufa @@ -0,0 +1,119 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = macway_lufa + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + + +# List C source files here. (C dependencies are automatically generated.) +SRC += keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support + + +# Boot Section Size in bytes +# Teensy halfKay 512 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +#OPT_DEFS += -DBOOT_SIZE=4096 + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/lufa.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk diff --git a/keyboard/macway/Makefile.pjrc b/keyboard/macway/Makefile.pjrc new file mode 100644 index 0000000000..ecc236e3d0 --- /dev/null +++ b/keyboard/macway/Makefile.pjrc @@ -0,0 +1,95 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + +# Target file name (without extension). +TARGET = macway_pjrc + +# Directory common source filess exist +TOP_DIR = ../.. + +# Directory keyboard dependent files exist +TARGET_DIR = . + +# keyboard dependent files +SRC = keymap.c \ + matrix.c \ + led.c + +CONFIG_H = config.h + + +# MCU name, you MUST set this to match the board you are using +# type "make clean" after changing this, so all files will be rebuilt +#MCU = at90usb162 # Teensy 1.0 +MCU = atmega32u4 # Teensy 2.0 +#MCU = at90usb646 # Teensy++ 1.0 +#MCU = at90usb1286 # Teensy++ 2.0 + + +# Processor frequency. +# Normally the first thing your program should do is set the clock prescaler, +# so your program will run at the correct speed. You should also set this +# variable to same clock speed. The _delay_ms() macro uses this, and many +# examples use this variable to calculate timings. Do not add a "UL" here. +F_CPU = 16000000 + + +# Build Options +# comment out to disable the options. +# +MOUSEKEY_ENABLE = yes # Mouse keys +#PS2_MOUSE_ENABLE = yes # PS/2 mouse(TrackPoint) support +EXTRAKEY_ENABLE = yes # Audio control and System control +#NKRO_ENABLE = yes # USB Nkey Rollover + + + +#---------------- Programming Options -------------------------- +PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex + + + +# Search Path +VPATH += $(TARGET_DIR) +VPATH += $(TOP_DIR) + +include $(TOP_DIR)/protocol/pjrc.mk +include $(TOP_DIR)/common.mk +include $(TOP_DIR)/rules.mk diff --git a/keyboard/macway/config.h b/keyboard/macway/config.h index b68ea20dcf..5503c77e3a 100644 --- a/keyboard/macway/config.h +++ b/keyboard/macway/config.h @@ -21,10 +21,16 @@ along with this program. If not, see <http://www.gnu.org/licenses/>. /* controller configuration */ #include "controller_teensy.h" + +/* USB Device descriptor parameter */ #define VENDOR_ID 0xFEED #define PRODUCT_ID 0xBEE0 +#define DEVICE_VER 0x0202 #define MANUFACTURER t.m.k. #define PRODUCT Macway mod + + +/* message strings */ #define DESCRIPTION t.m.k. keyboard firmware for Macway mod diff --git a/keyboard/macway/keymap.c b/keyboard/macway/keymap.c index 89634e2f41..76c0d8b724 100644 --- a/keyboard/macway/keymap.c +++ b/keyboard/macway/keymap.c @@ -59,7 +59,7 @@ static const uint8_t PROGMEM fn_layer[] = { 3, // Fn3 4, // Fn4 0, // Fn5 - 2, // Fn6 + 3, // Fn6 3 // Fn7 }; @@ -94,7 +94,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { TAB, Q, W, E, R, T, Y, U, I, O, P, LBRC,RBRC,BSLS, \ LCTL,A, S, D, F, G, H, J, K, L, FN3, QUOT,ENT, \ LSFT,Z, X, C, V, B, N, M, COMM,DOT, FN2, RSFT,FN1, \ - FN7, LGUI,LALT,FN4, RALT,BSLS,GRV, FN6, RCTL), + FN7, LGUI,LALT,FN4, RALT,GRV, FN6, FN6, RCTL), /* Layer 1: HHKB mode (HHKB Fn) @@ -110,8 +110,8 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { * | |Gui |Alt | |Alt |Gui| | |Ctr| * `-----------------------------------------------------------' */ - KEYMAP(ESC, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, \ - CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,BRK, UP, NO, NO, \ + KEYMAP(PWR, F1, F2, F3, F4, F5, F6, F7, F8, F9, F10, F11, F12, DEL, \ + CAPS,NO, NO, NO, NO, NO, NO, NO, PSCR,SLCK,BRK, UP, NO, NLCK,\ LCTL,VOLD,VOLU,MUTE,NO, NO, PAST,PSLS,HOME,PGUP,LEFT,RGHT,ENT, \ LSFT,NO, NO, NO, NO, NO, PPLS,PMNS,END, PGDN,DOWN,RSFT,FN1, \ NO, LGUI,LALT,SPC, RALT,NO, NO, NO, RCTL), @@ -155,7 +155,7 @@ static const uint8_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { BSLS,WH_L,WH_D,MS_U,WH_U,WH_R,WH_L,WH_D,WH_U,WH_R,NO, NO, NO, NO, \ LCTL,NO, MS_L,MS_D,MS_R,NO, MS_L,MS_D,MS_U,MS_R,FN3, NO, BSLS, \ LSFT,NO, NO, BTN1,BTN2,BTN3,BTN2,BTN1,NO, NO, NO, RSFT,NO, \ - FN7, LGUI,LALT,BTN1,RALT,NO, NO, NO, NO), + FN7, LGUI,LALT,BTN1,RALT,NO, FN6, FN6, NO), /* Layer 4: Matias half keyboard style (Space) |