diff options
Diffstat (limited to 'converter/adb_usb/Makefile')
| -rw-r--r-- | converter/adb_usb/Makefile | 108 |
1 files changed, 88 insertions, 20 deletions
diff --git a/converter/adb_usb/Makefile b/converter/adb_usb/Makefile index 09f30180a8..372ef6c09a 100644 --- a/converter/adb_usb/Makefile +++ b/converter/adb_usb/Makefile @@ -1,5 +1,45 @@ +#---------------------------------------------------------------------------- +# On command line: +# +# make all = Make software. +# +# make clean = Clean out built project files. +# +# make coff = Convert ELF to AVR COFF. +# +# make extcoff = Convert ELF to AVR Extended COFF. +# +# make program = Download the hex file to the device. +# Please customize your programmer settings(PROGRAM_CMD) +# +# make teensy = Download the hex file to the device, using teensy_loader_cli. +# (must have teensy_loader_cli installed). +# +# make dfu = Download the hex file to the device, using dfu-programmer (must +# have dfu-programmer installed). +# +# make flip = Download the hex file to the device, using Atmel FLIP (must +# have Atmel FLIP installed). +# +# make dfu-ee = Download the eeprom file to the device, using dfu-programmer +# (must have dfu-programmer installed). +# +# make flip-ee = Download the eeprom file to the device, using Atmel FLIP +# (must have Atmel FLIP installed). +# +# make debug = Start either simulavr or avarice as specified for debugging, +# with avr-gdb or avr-insight as the front end for debugging. +# +# make filename.s = Just compile filename.c into the assembler code only. +# +# make filename.i = Create a preprocessed source file for use in submitting +# bug reports to the GCC project. +# +# To rebuild project do "make clean" then "make all". +#---------------------------------------------------------------------------- + # Target file name (without extension). -TARGET = adb_usb +TARGET = adb_usb_lufa # Directory common source filess exist TOP_DIR = ../.. @@ -7,7 +47,7 @@ TOP_DIR = ../.. # Directory keyboard dependent files exist TARGET_DIR = . -# keyboard dependent files +# project specific files SRC = keymap.c \ matrix.c \ led.c \ @@ -16,22 +56,47 @@ SRC = keymap.c \ CONFIG_H = config.h -# MCU name, you MUST set this to match the board you are using -# type "make clean" after changing this, so all files will be rebuilt -#MCU = at90usb162 # Teensy 1.0 -MCU = atmega32u4 # Teensy 2.0 -#MCU = at90usb646 # Teensy++ 1.0 -#MCU = at90usb1286 # Teensy++ 2.0 - +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 # Processor frequency. -# Normally the first thing your program should do is set the clock prescaler, -# so your program will run at the correct speed. You should also set this -# variable to same clock speed. The _delay_ms() macro uses this, and many -# examples use this variable to calculate timings. Do not add a "UL" here. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. F_CPU = 16000000 +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +#OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + # Boot Section Size in *bytes* # Teensy halfKay 512 # Teensy++ halfKay 1024 @@ -44,20 +109,23 @@ OPT_DEFS += -DBOOTLOADER_SIZE=4096 # Build Options # comment out to disable the options. # -#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) -#MOUSEKEY_ENABLE = yes # Mouse keys(+5000) -#EXTRAKEY_ENABLE = yes # Audio control and System control(+600) -#CONSOLE_ENABLE = yes # Console for debug -#COMMAND_ENABLE = yes # Commands for debug and configuration +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = yes # Console for debug(+400) +COMMAND_ENABLE = yes # Commands for debug and configuration #SLEEP_LED_ENABLE = yes # Breathing sleep LED during USB suspend -#NKRO_ENABLE = yes # USB Nkey Rollover(+500) +#NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA + +# Optimize size but this may cause error "relocation truncated to fit" +#EXTRALDFLAGS = -Wl,--relax # Search Path VPATH += $(TARGET_DIR) VPATH += $(TOP_DIR) -include $(TOP_DIR)/protocol/pjrc.mk +include $(TOP_DIR)/protocol/lufa.mk include $(TOP_DIR)/protocol.mk include $(TOP_DIR)/common.mk include $(TOP_DIR)/rules.mk |